diff options
| -rw-r--r-- | drivers/mtd/onenand/onenand_base.c | 54 |
1 files changed, 25 insertions, 29 deletions
diff --git a/drivers/mtd/onenand/onenand_base.c b/drivers/mtd/onenand/onenand_base.c index 5d7965f7e9ce..926cf3a4135d 100644 --- a/drivers/mtd/onenand/onenand_base.c +++ b/drivers/mtd/onenand/onenand_base.c @@ -325,28 +325,11 @@ static int onenand_wait(struct mtd_info *mtd, int state) ctrl = this->read_word(this->base + ONENAND_REG_CTRL_STATUS); - if (ctrl & ONENAND_CTRL_ERROR) { - printk(KERN_ERR "onenand_wait: controller error = 0x%04x\n", ctrl); - if (ctrl & ONENAND_CTRL_LOCK) - printk(KERN_ERR "onenand_wait: it's locked error.\n"); - if (state == FL_READING) { - /* - * A power loss while writing can result in a page - * becoming unreadable. When the device is mounted - * again, reading that page gives controller errors. - * Upper level software like JFFS2 treat -EIO as fatal, - * refusing to mount at all. That means it is necessary - * to treat the error as an ECC error to allow recovery. - * Note that typically in this case, the eraseblock can - * still be erased and rewritten i.e. it has not become - * a bad block. - */ - mtd->ecc_stats.failed++; - return -EBADMSG; - } - return -EIO; - } - + /* + * In the Spec. it checks the controller status first + * However if you get the correct information in case of + * power off recovery (POR) test, it should read ECC status first + */ if (interrupt & ONENAND_INT_READ) { int ecc = this->read_word(this->base + ONENAND_REG_ECC_STATUS); if (ecc) { @@ -364,6 +347,15 @@ static int onenand_wait(struct mtd_info *mtd, int state) return -EIO; } + /* If there's controller error, it's a real error */ + if (ctrl & ONENAND_CTRL_ERROR) { + printk(KERN_ERR "onenand_wait: controller error = 0x%04x\n", + ctrl); + if (ctrl & ONENAND_CTRL_LOCK) + printk(KERN_ERR "onenand_wait: it's locked error.\n"); + return -EIO; + } + return 0; } @@ -1135,22 +1127,26 @@ static int onenand_bbt_wait(struct mtd_info *mtd, int state) interrupt = this->read_word(this->base + ONENAND_REG_INTERRUPT); ctrl = this->read_word(this->base + ONENAND_REG_CTRL_STATUS); - /* Initial bad block case: 0x2400 or 0x0400 */ - if (ctrl & ONENAND_CTRL_ERROR) { - printk(KERN_DEBUG "onenand_bbt_wait: controller error = 0x%04x\n", ctrl); - return ONENAND_BBT_READ_ERROR; - } - if (interrupt & ONENAND_INT_READ) { int ecc = this->read_word(this->base + ONENAND_REG_ECC_STATUS); - if (ecc & ONENAND_ECC_2BIT_ALL) + if (ecc & ONENAND_ECC_2BIT_ALL) { + printk(KERN_INFO "onenand_bbt_wait: ecc error = 0x%04x" + ", controller error 0x%04x\n", ecc, ctrl); return ONENAND_BBT_READ_ERROR; + } } else { printk(KERN_ERR "onenand_bbt_wait: read timeout!" "ctrl=0x%04x intr=0x%04x\n", ctrl, interrupt); return ONENAND_BBT_READ_FATAL_ERROR; } + /* Initial bad block case: 0x2400 or 0x0400 */ + if (ctrl & ONENAND_CTRL_ERROR) { + printk(KERN_DEBUG "onenand_bbt_wait: " + "controller error = 0x%04x\n", ctrl); + return ONENAND_BBT_READ_ERROR; + } + return 0; } |