1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
|
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
%YAML 1.2
---
$id: http://devicetree.org/schemas/iio/imu/adi,adis16475.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#
title: Analog Devices ADIS16475 and similar IMUs
maintainers:
- Nuno Sá <nuno.sa@analog.com>
description: |
Analog Devices ADIS16475 and similar IMUs
https://www.analog.com/media/en/technical-documentation/data-sheets/ADIS16475.pdf
properties:
compatible:
enum:
- adi,adis16475-1
- adi,adis16475-2
- adi,adis16475-3
- adi,adis16477-1
- adi,adis16477-2
- adi,adis16477-3
- adi,adis16470
- adi,adis16465-1
- adi,adis16465-2
- adi,adis16465-3
- adi,adis16467-1
- adi,adis16467-2
- adi,adis16467-3
- adi,adis16500
- adi,adis16505-1
- adi,adis16505-2
- adi,adis16505-3
- adi,adis16507-1
- adi,adis16507-2
- adi,adis16507-3
reg:
maxItems: 1
spi-cpha: true
spi-cpol: true
spi-max-frequency:
maximum: 2000000
interrupts:
maxItems: 1
clocks:
maxItems: 1
reset-gpios:
description:
Must be the device tree identifier of the RESET pin. If specified,
it will be asserted during driver probe. As the line is active low,
it should be marked GPIO_ACTIVE_LOW.
maxItems: 1
adi,sync-mode:
description:
Configures the device SYNC pin. The following modes are supported
0 - output_sync
1 - direct_sync
2 - scaled_sync
3 - pulse_sync
$ref: /schemas/types.yaml#/definitions/uint32
minimum: 0
maximum: 3
required:
- compatible
- reg
- interrupts
- spi-cpha
- spi-cpol
allOf:
- if:
properties:
compatible:
contains:
enum:
- adi,adis16500
- adi,adis16505-1
- adi,adis16505-2
- adi,adis16505-3
- adi,adis16507-1
- adi,adis16507-2
- adi,adis16507-3
then:
properties:
adi,sync-mode:
minimum: 0
maximum: 2
- if:
properties:
adi,sync-mode:
enum: [1, 2, 3]
then:
dependencies:
adi,sync-mode: [ clocks ]
additionalProperties: false
examples:
- |
#include <dt-bindings/interrupt-controller/irq.h>
spi {
#address-cells = <1>;
#size-cells = <0>;
adis16475: adis16475-3@0 {
compatible = "adi,adis16475-3";
reg = <0>;
spi-cpha;
spi-cpol;
spi-max-frequency = <2000000>;
interrupts = <4 IRQ_TYPE_EDGE_RISING>;
interrupt-parent = <&gpio>;
};
};
...
|
