Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC cleanups from Arnd Bergmann:
 "The cleanups for v4.9 are a little larger that usual, but thankfully
  that is almost exclusively due to removing a significant number of
  files that have become obsolete after the still ongoing conversion of
  old board files to devicetree.

   - for mach-omap2, which is still the largest platform in arch/arm/,
     the conversion to DT is finally complete after the Nokia N900 is
     now fully supported there, along with the omap3 LDP, and we can
     remove those two board files. If no regressions are found, another
     large cleanup for the platform will happen as a follow-up, removing
     dead code and restructuring the platform based on being DT-only.

   - In mach-imx, similar work is ongoing, but has not come that far.
     This time, we remove the obsolete board file for the i.MX1
     generation, which like i.MX25, i.MX5, i.MX6, and i.MX7 is now
     DT-only. The remaining board files are for i.MX2 and i.MX3 machines
     based on old ARM926 or ARM1136 cores that should work with DT in
     principle.

   - realview has just been converted from board files to DT, and a lot
     of code gets removed in the process. This is the last
     ARM/Keil/Versatile derived platform that was still using board
     files, the other ones being integrator, versatile and vexpress. We
     can probably merge the remaining code into a single directory in
     the near future.

   - clps711x had completed the conversion in v4.8, but we accidentally
     left the files in place that should have been deleted then"

* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
  ARM: select PCI_DOMAINS config from ARCH_MULTIPLATFORM
  ARM: stop *MIGHT_HAVE_PCI* config from being selected redundantly
  ARM: imx: (trivial) fix typo and grammar
  ARM: clps711x: remove extraneous files
  ARM: imx: use IS_ENABLED() instead of checking for built-in or module
  ARM: OMAP2+: use IS_ENABLED() instead of checking for built-in or module
  ARM: OMAP1: use IS_ENABLED() instead of checking for built-in or module
  ARM: imx: remove platform-mxc_rnga
  ARM: realview: imply device tree boot
  ARM: realview: no need to select SMP_ON_UP explicitly
  ARM: realview: delete the RealView board files
  ARM: imx: no need to select SMP_ON_UP explicitly
  ARM: i.MX: Move SOC_IMX1 into 'Device tree only'
  ARM: i.MX: Remove i.MX1 non-DT support
  ARM: i.MX: Remove i.MX1 Synertronixx SCB9328 board support
  ARM: i.MX: Remove i.MX1 Armadeus APF9328 board support
  ARM: mxs: remove obsolete startup code for TX28
  ARM: i.MX31 iomux: remove duplicates with alternate name
  ARM: i.MX31 iomux: remove plain duplicates
  ARM: OMAP2+: Drop legacy board file for LDP
  ...

1 files changed, 0 insertions, 87 deletions

diff --git a/arch/arm/mach-realview/irqs-pbx.h b/arch/arm/mach-realview/irqs-pbx.h
deleted file mode 100644
index 4ef0567dec32..000000000000
--- a/arch/arm/mach-realview/irqs-pbx.h
+++ /dev/null
@@ -1,87 +0,0 @@
-/*
- * Copyright (C) 2009 ARM Limited
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
- */
-
-#ifndef __MACH_IRQS_PBX_H
-#define __MACH_IRQS_PBX_H
-
-#define IRQ_LOCALTIMER				29
-#define IRQ_PBX_GIC_START			32
-
-/*
- * PBX on-board gic irq sources
- */
-#define IRQ_PBX_WATCHDOG	(IRQ_PBX_GIC_START + 0)	/* Watchdog timer */
-#define IRQ_PBX_SOFT		(IRQ_PBX_GIC_START + 1)	/* Software interrupt */
-#define IRQ_PBX_COMMRx		(IRQ_PBX_GIC_START + 2)	/* Debug Comm Rx interrupt */
-#define IRQ_PBX_COMMTx		(IRQ_PBX_GIC_START + 3)	/* Debug Comm Tx interrupt */
-#define IRQ_PBX_TIMER0_1	(IRQ_PBX_GIC_START + 4)	/* Timer 0/1 (default timer) */
-#define IRQ_PBX_TIMER2_3	(IRQ_PBX_GIC_START + 5)	/* Timer 2/3 */
-#define IRQ_PBX_GPIO0		(IRQ_PBX_GIC_START + 6)	/* GPIO 0 */
-#define IRQ_PBX_GPIO1		(IRQ_PBX_GIC_START + 7)	/* GPIO 1 */
-#define IRQ_PBX_GPIO2		(IRQ_PBX_GIC_START + 8)	/* GPIO 2 */
-								/* 9 reserved */
-#define IRQ_PBX_RTC		(IRQ_PBX_GIC_START + 10)	/* Real Time Clock */
-#define IRQ_PBX_SSP		(IRQ_PBX_GIC_START + 11)	/* Synchronous Serial Port */
-#define IRQ_PBX_UART0		(IRQ_PBX_GIC_START + 12)	/* UART 0 on development chip */
-#define IRQ_PBX_UART1		(IRQ_PBX_GIC_START + 13)	/* UART 1 on development chip */
-#define IRQ_PBX_UART2		(IRQ_PBX_GIC_START + 14)	/* UART 2 on development chip */
-#define IRQ_PBX_UART3		(IRQ_PBX_GIC_START + 15)	/* UART 3 on development chip */
-#define IRQ_PBX_SCI		(IRQ_PBX_GIC_START + 16)	/* Smart Card Interface */
-#define IRQ_PBX_MMCI0A		(IRQ_PBX_GIC_START + 17)	/* Multimedia Card 0A */
-#define IRQ_PBX_MMCI0B		(IRQ_PBX_GIC_START + 18)	/* Multimedia Card 0B */
-#define IRQ_PBX_AACI		(IRQ_PBX_GIC_START + 19)	/* Audio Codec */
-#define IRQ_PBX_KMI0		(IRQ_PBX_GIC_START + 20)	/* Keyboard/Mouse port 0 */
-#define IRQ_PBX_KMI1		(IRQ_PBX_GIC_START + 21)	/* Keyboard/Mouse port 1 */
-#define IRQ_PBX_CHARLCD		(IRQ_PBX_GIC_START + 22)	/* Character LCD */
-#define IRQ_PBX_CLCD		(IRQ_PBX_GIC_START + 23)	/* CLCD controller */
-#define IRQ_PBX_DMAC		(IRQ_PBX_GIC_START + 24)	/* DMA controller */
-#define IRQ_PBX_PWRFAIL		(IRQ_PBX_GIC_START + 25)	/* Power failure */
-#define IRQ_PBX_PISMO		(IRQ_PBX_GIC_START + 26)	/* PISMO interface */
-#define IRQ_PBX_DoC		(IRQ_PBX_GIC_START + 27)	/* Disk on Chip memory controller */
-#define IRQ_PBX_ETH		(IRQ_PBX_GIC_START + 28)	/* Ethernet controller */
-#define IRQ_PBX_USB		(IRQ_PBX_GIC_START + 29)	/* USB controller */
-#define IRQ_PBX_TSPEN		(IRQ_PBX_GIC_START + 30)	/* Touchscreen pen */
-#define IRQ_PBX_TSKPAD		(IRQ_PBX_GIC_START + 31)	/* Touchscreen keypad */
-
-#define IRQ_PBX_PMU_SCU0        (IRQ_PBX_GIC_START + 32)        /* SCU PMU Interrupts (11mp) */
-#define IRQ_PBX_PMU_SCU1        (IRQ_PBX_GIC_START + 33)
-#define IRQ_PBX_PMU_SCU2        (IRQ_PBX_GIC_START + 34)
-#define IRQ_PBX_PMU_SCU3        (IRQ_PBX_GIC_START + 35)
-#define IRQ_PBX_PMU_SCU4        (IRQ_PBX_GIC_START + 36)
-#define IRQ_PBX_PMU_SCU5        (IRQ_PBX_GIC_START + 37)
-#define IRQ_PBX_PMU_SCU6        (IRQ_PBX_GIC_START + 38)
-#define IRQ_PBX_PMU_SCU7        (IRQ_PBX_GIC_START + 39)
-
-#define IRQ_PBX_WATCHDOG1       (IRQ_PBX_GIC_START + 40)        /* Watchdog1 timer */
-#define IRQ_PBX_TIMER4_5        (IRQ_PBX_GIC_START + 41)        /* Timer 0/1 (default timer) */
-#define IRQ_PBX_TIMER6_7        (IRQ_PBX_GIC_START + 42)        /* Timer 2/3 */
-/* ... */
-#define IRQ_PBX_PMU_CPU0        (IRQ_PBX_GIC_START + 44)        /* CPU PMU Interrupts */
-#define IRQ_PBX_PMU_CPU1        (IRQ_PBX_GIC_START + 45)
-#define IRQ_PBX_PMU_CPU2        (IRQ_PBX_GIC_START + 46)
-#define IRQ_PBX_PMU_CPU3        (IRQ_PBX_GIC_START + 47)
-
-/* ... */
-#define IRQ_PBX_PCI0		(IRQ_PBX_GIC_START + 50)
-#define IRQ_PBX_PCI1		(IRQ_PBX_GIC_START + 51)
-#define IRQ_PBX_PCI2		(IRQ_PBX_GIC_START + 52)
-#define IRQ_PBX_PCI3		(IRQ_PBX_GIC_START + 53)
-
-#define IRQ_PBX_SMC		-1
-#define IRQ_PBX_SCTL		-1
-
-#endif	/* __MACH_IRQS_PBX_H */