diff options
Diffstat (limited to 'drivers/net/ixgbe/ixgbe_82599.c')
| -rw-r--r-- | drivers/net/ixgbe/ixgbe_82599.c | 178 |
1 files changed, 175 insertions, 3 deletions
diff --git a/drivers/net/ixgbe/ixgbe_82599.c b/drivers/net/ixgbe/ixgbe_82599.c index 34b04924c8a1..72106898a5cb 100644 --- a/drivers/net/ixgbe/ixgbe_82599.c +++ b/drivers/net/ixgbe/ixgbe_82599.c @@ -42,6 +42,10 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, ixgbe_link_speed speed, bool autoneg, bool autoneg_wait_to_complete); +static s32 ixgbe_setup_mac_link_smartspeed(struct ixgbe_hw *hw, + ixgbe_link_speed speed, + bool autoneg, + bool autoneg_wait_to_complete); s32 ixgbe_start_mac_link_82599(struct ixgbe_hw *hw, bool autoneg_wait_to_complete); s32 ixgbe_setup_mac_link_82599(struct ixgbe_hw *hw, @@ -64,7 +68,13 @@ static void ixgbe_init_mac_link_ops_82599(struct ixgbe_hw *hw) /* Set up dual speed SFP+ support */ mac->ops.setup_link = &ixgbe_setup_mac_link_multispeed_fiber; } else { - mac->ops.setup_link = &ixgbe_setup_mac_link_82599; + if ((mac->ops.get_media_type(hw) == + ixgbe_media_type_backplane) && + (hw->phy.smart_speed == ixgbe_smart_speed_auto || + hw->phy.smart_speed == ixgbe_smart_speed_on)) + mac->ops.setup_link = &ixgbe_setup_mac_link_smartspeed; + else + mac->ops.setup_link = &ixgbe_setup_mac_link_82599; } } @@ -337,6 +347,7 @@ static enum ixgbe_media_type ixgbe_get_media_type_82599(struct ixgbe_hw *hw) media_type = ixgbe_media_type_backplane; break; case IXGBE_DEV_ID_82599_SFP: + case IXGBE_DEV_ID_82599_SFP_EM: media_type = ixgbe_media_type_fiber; break; case IXGBE_DEV_ID_82599_CX4: @@ -479,7 +490,12 @@ s32 ixgbe_setup_mac_link_multispeed_fiber(struct ixgbe_hw *hw, hw->mac.autotry_restart = false; } - /* The controller may take up to 500ms at 10g to acquire link */ + /* + * Wait for the controller to acquire link. Per IEEE 802.3ap, + * Section 73.10.2, we may have to wait up to 500ms if KR is + * attempted. 82599 uses the same timing for 10g SFI. + */ + for (i = 0; i < 5; i++) { /* Wait for the link partner to also set speed */ msleep(100); @@ -567,6 +583,111 @@ out: } /** + * ixgbe_setup_mac_link_smartspeed - Set MAC link speed using SmartSpeed + * @hw: pointer to hardware structure + * @speed: new link speed + * @autoneg: true if autonegotiation enabled + * @autoneg_wait_to_complete: true when waiting for completion is needed + * + * Implements the Intel SmartSpeed algorithm. + **/ +static s32 ixgbe_setup_mac_link_smartspeed(struct ixgbe_hw *hw, + ixgbe_link_speed speed, bool autoneg, + bool autoneg_wait_to_complete) +{ + s32 status = 0; + ixgbe_link_speed link_speed; + s32 i, j; + bool link_up = false; + u32 autoc_reg = IXGBE_READ_REG(hw, IXGBE_AUTOC); + + hw_dbg(hw, "ixgbe_setup_mac_link_smartspeed.\n"); + + /* Set autoneg_advertised value based on input link speed */ + hw->phy.autoneg_advertised = 0; + + if (speed & IXGBE_LINK_SPEED_10GB_FULL) + hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_10GB_FULL; + + if (speed & IXGBE_LINK_SPEED_1GB_FULL) + hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_1GB_FULL; + + if (speed & IXGBE_LINK_SPEED_100_FULL) + hw->phy.autoneg_advertised |= IXGBE_LINK_SPEED_100_FULL; + + /* + * Implement Intel SmartSpeed algorithm. SmartSpeed will reduce the + * autoneg advertisement if link is unable to be established at the + * highest negotiated rate. This can sometimes happen due to integrity + * issues with the physical media connection. + */ + + /* First, try to get link with full advertisement */ + hw->phy.smart_speed_active = false; + for (j = 0; j < IXGBE_SMARTSPEED_MAX_RETRIES; j++) { + status = ixgbe_setup_mac_link_82599(hw, speed, autoneg, + autoneg_wait_to_complete); + if (status) + goto out; + + /* + * Wait for the controller to acquire link. Per IEEE 802.3ap, + * Section 73.10.2, we may have to wait up to 500ms if KR is + * attempted, or 200ms if KX/KX4/BX/BX4 is attempted, per + * Table 9 in the AN MAS. + */ + for (i = 0; i < 5; i++) { + mdelay(100); + + /* If we have link, just jump out */ + hw->mac.ops.check_link(hw, &link_speed, + &link_up, false); + if (link_up) + goto out; + } + } + + /* + * We didn't get link. If we advertised KR plus one of KX4/KX + * (or BX4/BX), then disable KR and try again. + */ + if (((autoc_reg & IXGBE_AUTOC_KR_SUPP) == 0) || + ((autoc_reg & IXGBE_AUTOC_KX4_KX_SUPP_MASK) == 0)) + goto out; + + /* Turn SmartSpeed on to disable KR support */ + hw->phy.smart_speed_active = true; + status = ixgbe_setup_mac_link_82599(hw, speed, autoneg, + autoneg_wait_to_complete); + if (status) + goto out; + + /* + * Wait for the controller to acquire link. 600ms will allow for + * the AN link_fail_inhibit_timer as well for multiple cycles of + * parallel detect, both 10g and 1g. This allows for the maximum + * connect attempts as defined in the AN MAS table 73-7. + */ + for (i = 0; i < 6; i++) { + mdelay(100); + + /* If we have link, just jump out */ + hw->mac.ops.check_link(hw, &link_speed, + &link_up, false); + if (link_up) + goto out; + } + + /* We didn't get link. Turn SmartSpeed back off. */ + hw->phy.smart_speed_active = false; + status = ixgbe_setup_mac_link_82599(hw, speed, autoneg, + autoneg_wait_to_complete); + +out: + return status; +} + +/** * ixgbe_check_mac_link_82599 - Determine link and speed status * @hw: pointer to hardware structure * @speed: pointer to link speed @@ -669,7 +790,8 @@ s32 ixgbe_setup_mac_link_82599(struct ixgbe_hw *hw, if (speed & IXGBE_LINK_SPEED_10GB_FULL) if (orig_autoc & IXGBE_AUTOC_KX4_SUPP) autoc |= IXGBE_AUTOC_KX4_SUPP; - if (orig_autoc & IXGBE_AUTOC_KR_SUPP) + if ((orig_autoc & IXGBE_AUTOC_KR_SUPP) && + (hw->phy.smart_speed_active == false)) autoc |= IXGBE_AUTOC_KR_SUPP; if (speed & IXGBE_LINK_SPEED_1GB_FULL) autoc |= IXGBE_AUTOC_KX_SUPP; @@ -878,6 +1000,10 @@ static s32 ixgbe_reset_hw_82599(struct ixgbe_hw *hw) hw->mac.num_rar_entries--; } + /* Store the alternative WWNN/WWPN prefix */ + hw->mac.ops.get_wwn_prefix(hw, &hw->mac.wwnn_prefix, + &hw->mac.wwpn_prefix); + reset_hw_out: return status; } @@ -2414,6 +2540,51 @@ fw_version_out: return status; } +/** + * ixgbe_get_wwn_prefix_82599 - Get alternative WWNN/WWPN prefix from + * the EEPROM + * @hw: pointer to hardware structure + * @wwnn_prefix: the alternative WWNN prefix + * @wwpn_prefix: the alternative WWPN prefix + * + * This function will read the EEPROM from the alternative SAN MAC address + * block to check the support for the alternative WWNN/WWPN prefix support. + **/ +static s32 ixgbe_get_wwn_prefix_82599(struct ixgbe_hw *hw, u16 *wwnn_prefix, + u16 *wwpn_prefix) +{ + u16 offset, caps; + u16 alt_san_mac_blk_offset; + + /* clear output first */ + *wwnn_prefix = 0xFFFF; + *wwpn_prefix = 0xFFFF; + + /* check if alternative SAN MAC is supported */ + hw->eeprom.ops.read(hw, IXGBE_ALT_SAN_MAC_ADDR_BLK_PTR, + &alt_san_mac_blk_offset); + + if ((alt_san_mac_blk_offset == 0) || + (alt_san_mac_blk_offset == 0xFFFF)) + goto wwn_prefix_out; + + /* check capability in alternative san mac address block */ + offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_CAPS_OFFSET; + hw->eeprom.ops.read(hw, offset, &caps); + if (!(caps & IXGBE_ALT_SAN_MAC_ADDR_CAPS_ALTWWN)) + goto wwn_prefix_out; + + /* get the corresponding prefix for WWNN/WWPN */ + offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWNN_OFFSET; + hw->eeprom.ops.read(hw, offset, wwnn_prefix); + + offset = alt_san_mac_blk_offset + IXGBE_ALT_SAN_MAC_ADDR_WWPN_OFFSET; + hw->eeprom.ops.read(hw, offset, wwpn_prefix); + +wwn_prefix_out: + return 0; +} + static struct ixgbe_mac_operations mac_ops_82599 = { .init_hw = &ixgbe_init_hw_generic, .reset_hw = &ixgbe_reset_hw_82599, @@ -2425,6 +2596,7 @@ static struct ixgbe_mac_operations mac_ops_82599 = { .get_mac_addr = &ixgbe_get_mac_addr_generic, .get_san_mac_addr = &ixgbe_get_san_mac_addr_82599, .get_device_caps = &ixgbe_get_device_caps_82599, + .get_wwn_prefix = &ixgbe_get_wwn_prefix_82599, .stop_adapter = &ixgbe_stop_adapter_generic, .get_bus_info = &ixgbe_get_bus_info_generic, .set_lan_id = &ixgbe_set_lan_id_multi_port_pcie, |