diff options
Diffstat (limited to 'drivers/staging')
| -rw-r--r-- | drivers/staging/Kconfig | 2 | ||||
| -rw-r--r-- | drivers/staging/Makefile | 1 | ||||
| -rw-r--r-- | drivers/staging/memrar/memrar_handler.c | 3 | ||||
| -rw-r--r-- | drivers/staging/rar_register/Kconfig | 30 | ||||
| -rw-r--r-- | drivers/staging/rar_register/Makefile | 2 | ||||
| -rw-r--r-- | drivers/staging/rar_register/rar_register.c | 675 | ||||
| -rw-r--r-- | drivers/staging/rar_register/rar_register.h | 44 |
7 files changed, 1 insertions, 756 deletions
diff --git a/drivers/staging/Kconfig b/drivers/staging/Kconfig index 929651725855..0e4122ed1b36 100644 --- a/drivers/staging/Kconfig +++ b/drivers/staging/Kconfig @@ -109,8 +109,6 @@ source "drivers/staging/hv/Kconfig" source "drivers/staging/vme/Kconfig" -source "drivers/staging/rar_register/Kconfig" - source "drivers/staging/memrar/Kconfig" source "drivers/staging/sep/Kconfig" diff --git a/drivers/staging/Makefile b/drivers/staging/Makefile index 6c5b5237ccb9..ecfb0bb990b6 100644 --- a/drivers/staging/Makefile +++ b/drivers/staging/Makefile @@ -36,7 +36,6 @@ obj-$(CONFIG_VT6656) += vt6656/ obj-$(CONFIG_FB_UDL) += udlfb/ obj-$(CONFIG_HYPERV) += hv/ obj-$(CONFIG_VME_BUS) += vme/ -obj-$(CONFIG_RAR_REGISTER) += rar_register/ obj-$(CONFIG_MRST_RAR_HANDLER) += memrar/ obj-$(CONFIG_DX_SEP) += sep/ obj-$(CONFIG_IIO) += iio/ diff --git a/drivers/staging/memrar/memrar_handler.c b/drivers/staging/memrar/memrar_handler.c index efa7fd62d390..41876f2b0e54 100644 --- a/drivers/staging/memrar/memrar_handler.c +++ b/drivers/staging/memrar/memrar_handler.c @@ -47,8 +47,7 @@ #include <linux/mm.h> #include <linux/ioport.h> #include <linux/io.h> - -#include "../rar_register/rar_register.h" +#include <linux/rar_register.h> #include "memrar.h" #include "memrar_allocator.h" diff --git a/drivers/staging/rar_register/Kconfig b/drivers/staging/rar_register/Kconfig deleted file mode 100644 index e9c27738199b..000000000000 --- a/drivers/staging/rar_register/Kconfig +++ /dev/null @@ -1,30 +0,0 @@ -# -# RAR device configuration -# - -menu "RAR Register Driver" -# -# Restricted Access Register Manager -# -config RAR_REGISTER - tristate "Restricted Access Region Register Driver" - depends on PCI - default n - ---help--- - This driver allows other kernel drivers access to the - contents of the restricted access region control registers. - - The restricted access region control registers - (rar_registers) are used to pass address and - locking information on restricted access regions - to other drivers that use restricted access regions. - - The restricted access regions are regions of memory - on the Intel MID Platform that are not accessible to - the x86 processor, but are accessible to dedicated - processors on board peripheral devices. - - The purpose of the restricted access regions is to - protect sensitive data from compromise by unauthorized - programs running on the x86 processor. -endmenu diff --git a/drivers/staging/rar_register/Makefile b/drivers/staging/rar_register/Makefile deleted file mode 100644 index d5954ccc16c9..000000000000 --- a/drivers/staging/rar_register/Makefile +++ /dev/null @@ -1,2 +0,0 @@ -EXTRA_CFLAGS += -DLITTLE__ENDIAN -obj-$(CONFIG_RAR_REGISTER) += rar_register.o diff --git a/drivers/staging/rar_register/rar_register.c b/drivers/staging/rar_register/rar_register.c deleted file mode 100644 index 618503f422ef..000000000000 --- a/drivers/staging/rar_register/rar_register.c +++ /dev/null @@ -1,675 +0,0 @@ -/* - * rar_register.c - An Intel Restricted Access Region register driver - * - * Copyright(c) 2009 Intel Corporation. All rights reserved. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of the GNU General Public License as - * published by the Free Software Foundation; either version 2 of the - * License, or (at your option) any later version. - * - * This program is distributed in the hope that it will be useful, - * but WITHOUT ANY WARRANTY; without even the implied warranty of - * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU - * General Public License for more details. - * - * You should have received a copy of the GNU General Public License - * along with this program; if not, write to the Free Software - * Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA - * 02111-1307, USA. - * - * ------------------------------------------------------------------- - * 20091204 Mark Allyn <mark.a.allyn@intel.com> - * Ossama Othman <ossama.othman@intel.com> - * Cleanup per feedback from Alan Cox and Arjan Van De Ven - * - * 20090806 Ossama Othman <ossama.othman@intel.com> - * Return zero high address if upper 22 bits is zero. - * Cleaned up checkpatch errors. - * Clarified that driver is dealing with bus addresses. - * - * 20090702 Ossama Othman <ossama.othman@intel.com> - * Removed unnecessary include directives - * Cleaned up spinlocks. - * Cleaned up logging. - * Improved invalid parameter checks. - * Fixed and simplified RAR address retrieval and RAR locking - * code. - * - * 20090626 Mark Allyn <mark.a.allyn@intel.com> - * Initial publish - */ - -#define DEBUG 1 - -#include "rar_register.h" - -#include <linux/module.h> -#include <linux/pci.h> -#include <linux/spinlock.h> -#include <linux/device.h> -#include <linux/kernel.h> - -/* === Lincroft Message Bus Interface === */ -#define LNC_MCR_OFFSET 0xD0 /* Message Control Register */ -#define LNC_MDR_OFFSET 0xD4 /* Message Data Register */ - -/* Message Opcodes */ -#define LNC_MESSAGE_READ_OPCODE 0xD0 -#define LNC_MESSAGE_WRITE_OPCODE 0xE0 - -/* Message Write Byte Enables */ -#define LNC_MESSAGE_BYTE_WRITE_ENABLES 0xF - -/* B-unit Port */ -#define LNC_BUNIT_PORT 0x3 - -/* === Lincroft B-Unit Registers - Programmed by IA32 firmware === */ -#define LNC_BRAR0L 0x10 -#define LNC_BRAR0H 0x11 -#define LNC_BRAR1L 0x12 -#define LNC_BRAR1H 0x13 -/* Reserved for SeP */ -#define LNC_BRAR2L 0x14 -#define LNC_BRAR2H 0x15 - -/* Moorestown supports three restricted access regions. */ -#define MRST_NUM_RAR 3 - -/* RAR Bus Address Range */ -struct rar_addr { - dma_addr_t low; - dma_addr_t high; -}; - -/* - * We create one of these for each RAR - */ -struct client { - int (*callback)(unsigned long data); - unsigned long driver_priv; - bool busy; -}; - -static DEFINE_MUTEX(rar_mutex); -static DEFINE_MUTEX(lnc_reg_mutex); - -/* - * One per RAR device (currently only one device) - */ -struct rar_device { - struct rar_addr rar_addr[MRST_NUM_RAR]; - struct pci_dev *rar_dev; - bool registered; - bool allocated; - struct client client[MRST_NUM_RAR]; -}; - -/* Current platforms have only one rar_device for 3 rar regions */ -static struct rar_device my_rar_device; - -/* - * Abstract out multiple device support. Current platforms only - * have a single RAR device. - */ - -/** - * alloc_rar_device - return a new RAR structure - * - * Return a new (but not yet ready) RAR device object - */ -static struct rar_device *alloc_rar_device(void) -{ - if (my_rar_device.allocated) - return NULL; - my_rar_device.allocated = 1; - return &my_rar_device; -} - -/** - * free_rar_device - free a RAR object - * @rar: the RAR device being freed - * - * Release a RAR object and any attached resources - */ -static void free_rar_device(struct rar_device *rar) -{ - pci_dev_put(rar->rar_dev); - rar->allocated = 0; -} - -/** - * _rar_to_device - return the device handling this RAR - * @rar: RAR number - * @off: returned offset - * - * Internal helper for looking up RAR devices. This and alloc are the - * two functions that need touching to go to multiple RAR devices. - */ -static struct rar_device *_rar_to_device(int rar, int *off) -{ - if (rar >= 0 && rar <= 3) { - *off = rar; - return &my_rar_device; - } - return NULL; -} - - -/** - * rar_to_device - return the device handling this RAR - * @rar: RAR number - * @off: returned offset - * - * Return the device this RAR maps to if one is present, otherwise - * returns NULL. Reports the offset relative to the base of this - * RAR device in off. - */ -static struct rar_device *rar_to_device(int rar, int *off) -{ - struct rar_device *rar_dev = _rar_to_device(rar, off); - if (rar_dev == NULL || !rar_dev->registered) - return NULL; - return rar_dev; -} - -/** - * rar_to_client - return the client handling this RAR - * @rar: RAR number - * - * Return the client this RAR maps to if a mapping is known, otherwise - * returns NULL. - */ -static struct client *rar_to_client(int rar) -{ - int idx; - struct rar_device *r = _rar_to_device(rar, &idx); - if (r != NULL) - return &r->client[idx]; - return NULL; -} - -/** - * rar_read_addr - retrieve a RAR mapping - * @pdev: PCI device for the RAR - * @offset: offset for message - * @addr: returned address - * - * Reads the address of a given RAR register. Returns 0 on success - * or an error code on failure. - */ -static int rar_read_addr(struct pci_dev *pdev, int offset, dma_addr_t *addr) -{ - /* - * ======== The Lincroft Message Bus Interface ======== - * Lincroft registers may be obtained via PCI from - * the host bridge using the Lincroft Message Bus - * Interface. That message bus interface is generally - * comprised of two registers: a control register (MCR, 0xDO) - * and a data register (MDR, 0xD4). - * - * The MCR (message control register) format is the following: - * 1. [31:24]: Opcode - * 2. [23:16]: Port - * 3. [15:8]: Register Offset - * 4. [7:4]: Byte Enables (use 0xF to set all of these bits - * to 1) - * 5. [3:0]: reserved - * - * Read (0xD0) and write (0xE0) opcodes are written to the - * control register when reading and writing to Lincroft - * registers, respectively. - * - * We're interested in registers found in the Lincroft - * B-unit. The B-unit port is 0x3. - * - * The six B-unit RAR register offsets we use are listed - * earlier in this file. - * - * Lastly writing to the MCR register requires the "Byte - * enables" bits to be set to 1. This may be achieved by - * writing 0xF at bit 4. - * - * The MDR (message data register) format is the following: - * 1. [31:0]: Read/Write Data - * - * Data being read from this register is only available after - * writing the appropriate control message to the MCR - * register. - * - * Data being written to this register must be written before - * writing the appropriate control message to the MCR - * register. - */ - - int result; - u32 addr32; - - /* Construct control message */ - u32 const message = - (LNC_MESSAGE_READ_OPCODE << 24) - | (LNC_BUNIT_PORT << 16) - | (offset << 8) - | (LNC_MESSAGE_BYTE_WRITE_ENABLES << 4); - - dev_dbg(&pdev->dev, "Offset for 'get' LNC MSG is %x\n", offset); - - /* - * We synchronize access to the Lincroft MCR and MDR registers - * until BOTH the command is issued through the MCR register - * and the corresponding data is read from the MDR register. - * Otherwise a race condition would exist between accesses to - * both registers. - */ - - mutex_lock(&lnc_reg_mutex); - - /* Send the control message */ - result = pci_write_config_dword(pdev, LNC_MCR_OFFSET, message); - if (!result) { - /* Read back the address as a 32bit value */ - result = pci_read_config_dword(pdev, LNC_MDR_OFFSET, &addr32); - *addr = (dma_addr_t)addr32; - } - mutex_unlock(&lnc_reg_mutex); - return result; -} - -/** - * rar_set_addr - Set a RAR mapping - * @pdev: PCI device for the RAR - * @offset: offset for message - * @addr: address to set - * - * Sets the address of a given RAR register. Returns 0 on success - * or an error code on failure. - */ -static int rar_set_addr(struct pci_dev *pdev, - int offset, - dma_addr_t addr) -{ - /* - * Data being written to this register must be written before - * writing the appropriate control message to the MCR - * register. - * See rar_get_addrs() for a description of the - * message bus interface being used here. - */ - - int result; - - /* Construct control message */ - u32 const message = (LNC_MESSAGE_WRITE_OPCODE << 24) - | (LNC_BUNIT_PORT << 16) - | (offset << 8) - | (LNC_MESSAGE_BYTE_WRITE_ENABLES << 4); - - /* - * We synchronize access to the Lincroft MCR and MDR registers - * until BOTH the command is issued through the MCR register - * and the corresponding data is read from the MDR register. - * Otherwise a race condition would exist between accesses to - * both registers. - */ - - mutex_lock(&lnc_reg_mutex); - - /* Send the control message */ - result = pci_write_config_dword(pdev, LNC_MDR_OFFSET, addr); - if (!result) - /* And address */ - result = pci_write_config_dword(pdev, LNC_MCR_OFFSET, message); - - mutex_unlock(&lnc_reg_mutex); - return result; -} - -/* - * rar_init_params - Initialize RAR parameters - * @rar: RAR device to initialise - * - * Initialize RAR parameters, such as bus addresses, etc. Returns 0 - * on success, or an error code on failure. - */ -static int init_rar_params(struct rar_device *rar) -{ - struct pci_dev *pdev = rar->rar_dev; - unsigned int i; - int result = 0; - int offset = 0x10; /* RAR 0 to 2 in order low/high/low/high/... */ - - /* Retrieve RAR start and end bus addresses. - * Access the RAR registers through the Lincroft Message Bus - * Interface on PCI device: 00:00.0 Host bridge. - */ - - for (i = 0; i < MRST_NUM_RAR; ++i) { - struct rar_addr *addr = &rar->rar_addr[i]; - - result = rar_read_addr(pdev, offset++, &addr->low); - if (result != 0) - return result; - - result = rar_read_addr(pdev, offset++, &addr->high); - if (result != 0) - return result; - - - /* - * Only the upper 22 bits of the RAR addresses are - * stored in their corresponding RAR registers so we - * must set the lower 10 bits accordingly. - - * The low address has its lower 10 bits cleared, and - * the high address has all its lower 10 bits set, - * e.g.: - * low = 0x2ffffc00 - */ - - addr->low &= (dma_addr_t)0xfffffc00u; - - /* - * Set bits 9:0 on uppser address if bits 31:10 are non - * zero; otherwize clear all bits - */ - - if ((addr->high & 0xfffffc00u) == 0) - addr->high = 0; - else - addr->high |= 0x3ffu; - } - /* Done accessing the device. */ - - if (result == 0) { - for (i = 0; i != MRST_NUM_RAR; ++i) { - /* - * "BRAR" refers to the RAR registers in the - * Lincroft B-unit. - */ - dev_info(&pdev->dev, "BRAR[%u] bus address range = " - "[%lx, %lx]\n", i, - (unsigned long)rar->rar_addr[i].low, - (unsigned long)rar->rar_addr[i].high); - } - } - return result; -} - -/** - * rar_get_address - get the bus address in a RAR - * @start: return value of start address of block - * @end: return value of end address of block - * - * The rar_get_address function is used by other device drivers - * to obtain RAR address information on a RAR. It takes three - * parameters: - * - * The function returns a 0 upon success or an error if there is no RAR - * facility on this system. - */ -int rar_get_address(int rar_index, dma_addr_t *start, dma_addr_t *end) -{ - int idx; - struct rar_device *rar = rar_to_device(rar_index, &idx); - - if (rar == NULL) { - WARN_ON(1); - return -ENODEV; - } - - *start = rar->rar_addr[idx].low; - *end = rar->rar_addr[idx].high; - return 0; -} -EXPORT_SYMBOL(rar_get_address); - -/** - * rar_lock - lock a RAR register - * @rar_index: RAR to lock (0-2) - * - * The rar_lock function is ued by other device drivers to lock an RAR. - * once a RAR is locked, it stays locked until the next system reboot. - * - * The function returns a 0 upon success or an error if there is no RAR - * facility on this system, or the locking fails - */ -int rar_lock(int rar_index) -{ - struct rar_device *rar; - int result; - int idx; - dma_addr_t low, high; - - rar = rar_to_device(rar_index, &idx); - - if (rar == NULL) { - WARN_ON(1); - return -EINVAL; - } - - low = rar->rar_addr[idx].low & 0xfffffc00u; - high = rar->rar_addr[idx].high & 0xfffffc00u; - - /* - * Only allow I/O from the graphics and Langwell; - * not from the x86 processor - */ - - if (rar_index == RAR_TYPE_VIDEO) { - low |= 0x00000009; - high |= 0x00000015; - } else if (rar_index == RAR_TYPE_AUDIO) { - /* Only allow I/O from Langwell; nothing from x86 */ - low |= 0x00000008; - high |= 0x00000018; - } else - /* Read-only from all agents */ - high |= 0x00000018; - - /* - * Now program the register using the Lincroft message - * bus interface. - */ - result = rar_set_addr(rar->rar_dev, - 2 * idx, low); - - if (result == 0) - result = rar_set_addr(rar->rar_dev, - 2 * idx + 1, high); - - return result; -} -EXPORT_SYMBOL(rar_lock); - -/** - * register_rar - register a RAR handler - * @num: RAR we wish to register for - * @callback: function to call when RAR support is available - * @data: data to pass to this function - * - * The register_rar function is to used by other device drivers - * to ensure that this driver is ready. As we cannot be sure of - * the compile/execute order of drivers in ther kernel, it is - * best to give this driver a callback function to call when - * it is ready to give out addresses. The callback function - * would have those steps that continue the initialization of - * a driver that do require a valid RAR address. One of those - * steps would be to call rar_get_address() - * - * This function return 0 on success an error code on failure. - */ -int register_rar(int num, int (*callback)(unsigned long data), - unsigned long data) -{ - /* For now we hardcode a single RAR device */ - struct rar_device *rar; - struct client *c; - int idx; - int retval = 0; - - mutex_lock(&rar_mutex); - - /* Do we have a client mapping for this RAR number ? */ - c = rar_to_client(num); - if (c == NULL) { - retval = -ERANGE; - goto done; - } - /* Is it claimed ? */ - if (c->busy) { - retval = -EBUSY; - goto done; - } - c->busy = 1; - - /* See if we have a handler for this RAR yet, if we do then fire it */ - rar = rar_to_device(num, &idx); - - if (rar) { - /* - * if the driver already registered, then we can simply - * call the callback right now - */ - (*callback)(data); - goto done; - } - - /* Arrange to be called back when the hardware is found */ - c->callback = callback; - c->driver_priv = data; -done: - mutex_unlock(&rar_mutex); - return retval; -} -EXPORT_SYMBOL(register_rar); - -/** - * unregister_rar - release a RAR allocation - * @num: RAR number - * - * Releases a RAR allocation, or pending allocation. If a callback is - * pending then this function will either complete before the unregister - * returns or not at all. - */ - -void unregister_rar(int num) -{ - struct client *c; - - mutex_lock(&rar_mutex); - c = rar_to_client(num); - if (c == NULL || !c->busy) - WARN_ON(1); - else - c->busy = 0; - mutex_unlock(&rar_mutex); -} -EXPORT_SYMBOL(unregister_rar); - -/** - * rar_callback - Process callbacks - * @rar: new RAR device - * - * Process the callbacks for a newly found RAR device. - */ - -static void rar_callback(struct rar_device *rar) -{ - struct client *c = &rar->client[0]; - int i; - - mutex_lock(&rar_mutex); - - rar->registered = 1; /* Ensure no more callbacks queue */ - - for (i = 0; i < MRST_NUM_RAR; i++) { - if (c->callback && c->busy) { - c->callback(c->driver_priv); - c->callback = NULL; - } - c++; - } - mutex_unlock(&rar_mutex); -} - -/** - * rar_probe - PCI probe callback - * @dev: PCI device - * @id: matching entry in the match table - * - * A RAR device has been discovered. Initialise it and if successful - * process any pending callbacks that can now be completed. - */ -static int rar_probe(struct pci_dev *dev, const struct pci_device_id *id) -{ - int error; - struct rar_device *rar; - - dev_dbg(&dev->dev, "PCI probe starting\n"); - - rar = alloc_rar_device(); - if (rar == NULL) - return -EBUSY; - - /* Enable the device */ - error = pci_enable_device(dev); - if (error) { - dev_err(&dev->dev, - "Error enabling RAR register PCI device\n"); - goto end_function; - } - - /* Fill in the rar_device structure */ - rar->rar_dev = pci_dev_get(dev); - pci_set_drvdata(dev, rar); - - /* - * Initialize the RAR parameters, which have to be retrieved - * via the message bus interface. - */ - error = init_rar_params(rar); - if (error) { - pci_disable_device(dev); - dev_err(&dev->dev, "Error retrieving RAR addresses\n"); - goto end_function; - } - /* now call anyone who has registered (using callbacks) */ - rar_callback(rar); - return 0; -end_function: - free_rar_device(rar); - return error; -} - -const struct pci_device_id rar_pci_id_tbl[] = { - { PCI_VDEVICE(INTEL, 0x4110) }, - { 0 } -}; - -MODULE_DEVICE_TABLE(pci, rar_pci_id_tbl); - -const struct pci_device_id *my_id_table = rar_pci_id_tbl; - -/* field for registering driver to PCI device */ -static struct pci_driver rar_pci_driver = { - .name = "rar_register_driver", - .id_table = rar_pci_id_tbl, - .probe = rar_probe, - /* Cannot be unplugged - no remove */ -}; - -static int __init rar_init_handler(void) -{ - return pci_register_driver(&rar_pci_driver); -} - -static void __exit rar_exit_handler(void) -{ - pci_unregister_driver(&rar_pci_driver); -} - -module_init(rar_init_handler); -module_exit(rar_exit_handler); - -MODULE_LICENSE("GPL"); -MODULE_DESCRIPTION("Intel Restricted Access Region Register Driver"); diff --git a/drivers/staging/rar_register/rar_register.h b/drivers/staging/rar_register/rar_register.h deleted file mode 100644 index ffa805780f85..000000000000 --- a/drivers/staging/rar_register/rar_register.h +++ /dev/null @@ -1,44 +0,0 @@ -/* - * Copyright (C) 2010 Intel Corporation. All rights reserved. - * - * This program is free software; you can redistribute it and/or - * modify it under the terms of version 2 of the GNU General - * Public License as published by the Free Software Foundation. - * - * This program is distributed in the hope that it will be - * useful, but WITHOUT ANY WARRANTY; without even the implied - * warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR - * PURPOSE. See the GNU General Public License for more details. - * You should have received a copy of the GNU General Public - * License along with this program; if not, write to the Free - * Software Foundation, Inc., 59 Temple Place - Suite 330, - * Boston, MA 02111-1307, USA. - * The full GNU General Public License is included in this - * distribution in the file called COPYING. - */ - - -#ifndef _RAR_REGISTER_H -#define _RAR_REGISTER_H - -#include <linux/types.h> - -/* following are used both in drivers as well as user space apps */ - -#define RAR_TYPE_VIDEO 0 -#define RAR_TYPE_AUDIO 1 -#define RAR_TYPE_IMAGE 2 -#define RAR_TYPE_DATA 3 - -#ifdef __KERNEL__ - -struct rar_device; - -int register_rar(int num, - int (*callback)(unsigned long data), unsigned long data); -void unregister_rar(int num); -int rar_get_address(int rar_index, dma_addr_t *start, dma_addr_t *end); -int rar_lock(int rar_index); - -#endif /* __KERNEL__ */ -#endif /* _RAR_REGISTER_H */ |