summaryrefslogtreecommitdiff
path: root/drivers/mmc/core/bus.c
Commit message (Collapse)AuthorAgeFilesLines
* driver core: make struct bus_type.uevent() take a const *Greg Kroah-Hartman2023-01-271-2/+2
| | | | | | | | | | | | The uevent() callback in struct bus_type should not be modifying the device that is passed into it, so mark it as a const * and propagate the function signature changes out into all relevant subsystems that use this callback. Acked-by: Rafael J. Wysocki <rafael@kernel.org> Acked-by: Hans de Goede <hdegoede@redhat.com> Link: https://lore.kernel.org/r/20230111113018.459199-16-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* mmc: core: refactor debugfs codeYe Bin2022-12-071-4/+0
| | | | | | | | | Now, CONFIG_DEBUG_FS is scattered in various functions, to make code clean centralized processing CONFIG_DEBUG_FS in mmc debugfs module. Signed-off-by: Ye Bin <yebin10@huawei.com> Link: https://lore.kernel.org/r/20221126102520.2824574-1-yebin@huaweicloud.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: core: Use mmc_card_* macro and add a new for the sd_combo typeSeunghui Lee2022-07-131-2/+2
| | | | | | | | | Add mmc_card_sd_combo() macro for sd combo type card and use the mmc_card_* macro to simplify code instead of comparing card->type. Signed-off-by: Seunghui Lee <sh043.lee@samsung.com> Link: https://lore.kernel.org/r/20220713033635.28432-2-sh043.lee@samsung.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: core: use sysfs_emit() instead of sprintf()Sergey Shtylyov2022-02-281-4/+5
| | | | | | | | | | | | | sprintf() (still used in the MMC core for the sysfs output) is vulnerable to the buffer overflow. Use the new-fangled sysfs_emit() instead. Found by Linux Verification Center (linuxtesting.org) with the SVACE static analysis tool. Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/717729b2-d65b-c72e-9fac-471d28d00b5a@omp.ru Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: core: Remove redundant driver match functionlizhe2021-12-141-11/+0
| | | | | | | | | | | | | If there is no driver match function, the driver core assumes that each candidate pair (driver, device) matches, see driver_match_device(). Drop the mmc bus's match function that always returned 1 and so implements the same behaviour as when there is no match function. Signed-off-by: lizhe <sensor1010@163.com> Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20211207095029.96387-1-sensor1010@163.com Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* bus: Make remove callback return voidUwe Kleine-König2021-07-211-3/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The driver core ignores the return value of this callback because there is only little it can do when a device disappears. This is the final bit of a long lasting cleanup quest where several buses were converted to also return void from their remove callback. Additionally some resource leaks were fixed that were caused by drivers returning an error code in the expectation that the driver won't go away. With struct bus_type::remove returning void it's prevented that newly implemented buses return an ignored error code and so don't anticipate wrong expectations for driver authors. Reviewed-by: Tom Rix <trix@redhat.com> (For fpga) Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org> Reviewed-by: Cornelia Huck <cohuck@redhat.com> (For drivers/s390 and drivers/vfio) Acked-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> (For ARM, Amba and related parts) Acked-by: Mark Brown <broonie@kernel.org> Acked-by: Chen-Yu Tsai <wens@csie.org> (for sunxi-rsb) Acked-by: Pali Rohár <pali@kernel.org> Acked-by: Mauro Carvalho Chehab <mchehab@kernel.org> (for media) Acked-by: Hans de Goede <hdegoede@redhat.com> (For drivers/platform) Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Acked-By: Vinod Koul <vkoul@kernel.org> Acked-by: Juergen Gross <jgross@suse.com> (For xen) Acked-by: Lee Jones <lee.jones@linaro.org> (For mfd) Acked-by: Johannes Thumshirn <jth@kernel.org> (For mcb) Acked-by: Johan Hovold <johan@kernel.org> Acked-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> (For slimbus) Acked-by: Kirti Wankhede <kwankhede@nvidia.com> (For vfio) Acked-by: Maximilian Luz <luzmaximilian@gmail.com> Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com> (For ulpi and typec) Acked-by: Samuel Iglesias Gonsálvez <siglesias@igalia.com> (For ipack) Acked-by: Geoff Levand <geoff@infradead.org> (For ps3) Acked-by: Yehezkel Bernat <YehezkelShB@gmail.com> (For thunderbolt) Acked-by: Alexander Shishkin <alexander.shishkin@linux.intel.com> (For intel_th) Acked-by: Dominik Brodowski <linux@dominikbrodowski.net> (For pcmcia) Acked-by: Rafael J. Wysocki <rafael@kernel.org> (For ACPI) Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org> (rpmsg and apr) Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> (For intel-ish-hid) Acked-by: Dan Williams <dan.j.williams@intel.com> (For CXL, DAX, and NVDIMM) Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com> (For isa) Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (For firewire) Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com> (For hid) Acked-by: Thorsten Scherer <t.scherer@eckelmann.de> (For siox) Acked-by: Sven Van Asbroeck <TheSven73@gmail.com> (For anybuss) Acked-by: Ulf Hansson <ulf.hansson@linaro.org> (For MMC) Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C Acked-by: Sudeep Holla <sudeep.holla@arm.com> Acked-by: Geert Uytterhoeven <geert@linux-m68k.org> Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Acked-by: Finn Thain <fthain@linux-m68k.org> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Link: https://lore.kernel.org/r/20210713193522.1770306-6-u.kleine-koenig@pengutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* mmc: cqhci: Fix random crash when remove mmc module/cardFrank Li2021-03-091-6/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | [ 6684.493350] Unable to handle kernel paging request at virtual address ffff800011c5b0f0 [ 6684.498531] mmc0: card 0001 removed [ 6684.501556] Mem abort info: [ 6684.509681] ESR = 0x96000047 [ 6684.512786] EC = 0x25: DABT (current EL), IL = 32 bits [ 6684.518394] SET = 0, FnV = 0 [ 6684.521707] EA = 0, S1PTW = 0 [ 6684.524998] Data abort info: [ 6684.528236] ISV = 0, ISS = 0x00000047 [ 6684.532986] CM = 0, WnR = 1 [ 6684.536129] swapper pgtable: 4k pages, 48-bit VAs, pgdp=0000000081b22000 [ 6684.543923] [ffff800011c5b0f0] pgd=00000000bffff003, p4d=00000000bffff003, pud=00000000bfffe003, pmd=00000000900e1003, pte=0000000000000000 [ 6684.557915] Internal error: Oops: 96000047 [#1] PREEMPT SMP [ 6684.564240] Modules linked in: sdhci_esdhc_imx(-) sdhci_pltfm sdhci cqhci mmc_block mmc_core fsl_jr_uio caam_jr caamkeyblob_desc caamhash_desc caamalg_desc crypto_engine rng_core authenc libdes crct10dif_ce flexcan can_dev caam error [last unloaded: mmc_core] [ 6684.587281] CPU: 0 PID: 79138 Comm: kworker/0:3H Not tainted 5.10.9-01410-g3ba33182767b-dirty #10 [ 6684.596160] Hardware name: Freescale i.MX8DXL EVK (DT) [ 6684.601320] Workqueue: kblockd blk_mq_run_work_fn [ 6684.606094] pstate: 40000005 (nZcv daif -PAN -UAO -TCO BTYPE=--) [ 6684.612286] pc : cqhci_request+0x148/0x4e8 [cqhci] ^GMessage from syslogd@ at Thu Jan 1 01:51:24 1970 ...[ 6684.617085] lr : cqhci_request+0x314/0x4e8 [cqhci] [ 6684.626734] sp : ffff80001243b9f0 [ 6684.630049] x29: ffff80001243b9f0 x28: ffff00002c3dd000 [ 6684.635367] x27: 0000000000000001 x26: 0000000000000001 [ 6684.640690] x25: ffff00002c451000 x24: 000000000000000f [ 6684.646007] x23: ffff000017e71c80 x22: ffff00002c451000 [ 6684.651326] x21: ffff00002c0f3550 x20: ffff00002c0f3550 [ 6684.656651] x19: ffff000017d46880 x18: ffff00002cea1500 [ 6684.661977] x17: 0000000000000000 x16: 0000000000000000 [ 6684.667294] x15: 000001ee628e3ed1 x14: 0000000000000278 [ 6684.672610] x13: 0000000000000001 x12: 0000000000000001 [ 6684.677927] x11: 0000000000000000 x10: 0000000000000000 [ 6684.683243] x9 : 000000000000002b x8 : 0000000000001000 [ 6684.688560] x7 : 0000000000000010 x6 : ffff00002c0f3678 [ 6684.693886] x5 : 000000000000000f x4 : ffff800011c5b000 [ 6684.699211] x3 : 000000000002d988 x2 : 0000000000000008 [ 6684.704537] x1 : 00000000000000f0 x0 : 0002d9880008102f [ 6684.709854] Call trace: [ 6684.712313] cqhci_request+0x148/0x4e8 [cqhci] [ 6684.716803] mmc_cqe_start_req+0x58/0x68 [mmc_core] [ 6684.721698] mmc_blk_mq_issue_rq+0x460/0x810 [mmc_block] [ 6684.727018] mmc_mq_queue_rq+0x118/0x2b0 [mmc_block] The problem occurs when cqhci_request() get called after cqhci_disable() as it leads to access of allocated memory that has already been freed. Let's fix the problem by calling cqhci_disable() a bit later in the remove path. Signed-off-by: Frank Li <Frank.Li@nxp.com> Diagnosed-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Link: https://lore.kernel.org/r/20210303174248.542175-1-Frank.Li@nxp.com Fixes: f690f4409ddd ("mmc: mmc: Enable CQE's") Cc: stable@vger.kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: sdio: Export SDIO revision and info strings to userspacePali Rohár2020-09-071-0/+12
| | | | | | | | | | | | | | | | | For SDIO functions, SDIO cards and SD COMBO cards are exported revision number and info strings from CISTPL_VERS_1 structure. Revision number should indicate compliance of standard and info strings should contain product information in same format as product information for PCMCIA cards. Product information for PCMCIA cards should contain following strings in this order: Manufacturer, Product Name, Lot number, Programming Conditions. Note that not all SDIO cards export all those info strings in that order as described in PCMCIA Metaformat Specification. Signed-off-by: Pali Rohár <pali@kernel.org> Link: https://lore.kernel.org/r/20200727133837.19086-5-pali@kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: core: Export device/vendor ids from Common CIS for SDIO cardsPali Rohár2020-05-291-0/+7
| | | | | | | | | | | | | | | | | | | | | | | Device/vendor ids from Common CIS (Card Information Structure) may be different as device/vendor ids from CIS on particular SDIO function. Kernel currently exports only device/vendor ids from SDIO functions and not "main" device/vendor ids from Common CIS. This patch exports "main" device/vendor ids for SDIO and SD combo cards at top level mmc device in sysfs hierarchy. Userspace can use e.g. udev rules to correctly match whole SDIO card based on Common CIS device/vendor id and not only one particular SDIO function. Having this information in userspace also helps developers to debug whole SDIO card as e.g. kernel mmc quirks use device/vendor ids from Common CIS and not from particular SDIO function. Also it allows to write userspace applications which list all connected SDIO cards based on CIS ids. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Link: https://lore.kernel.org/r/20200527110858.17504-2-pali@kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: core: Do not export MMC_NAME= and MODALIAS=mmc:block for SDIO cardsPali Rohár2020-05-291-0/+7
| | | | | | | | | | SDIO non-combo cards are not handled by mmc_block driver and do not have accessible CID register which is used for MMC_NAME= construction. Signed-off-by: Pali Rohár <pali@kernel.org> Reviewed-by: Marek Behún <marek.behun@nic.cz> Link: https://lore.kernel.org/r/20200527110858.17504-1-pali@kernel.org Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500Thomas Gleixner2019-06-191-4/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* mmc: core: Remove code no longer needed after the switch to blk-mqAdrian Hunter2017-12-111-2/+0
| | | | | | | | | Remove code no longer needed after the switch to blk-mq. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: core: Do not leave the block driver in a suspended stateAdrian Hunter2017-11-231-0/+3
| | | | | | | | | The block driver must be resumed if the mmc bus fails to suspend the card. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Cc: stable@vger.kernel.org # v3.19+ Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: mmc: Enable CQE'sAdrian Hunter2017-10-301-0/+7
| | | | | | | | Enable or disable CQE when a card is added or removed respectively. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: core: Move public functions from host.h to private headersUlf Hansson2017-02-131-0/+1
| | | | | | | | | | | | | | A significant amount of functions are available through the public mmc host.h header file. Let's slim down this public mmc interface, as to prevent users from abusing it, by moving some of the functions to private mmc host.h header file. This change concentrates on moving the functions into private mmc headers, following changes may continue with additional clean-ups. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
* mmc: core: Move public functions from card.h to private headersUlf Hansson2017-02-131-0/+1
| | | | | | | | | | | | | | A significant amount of functions and other definitions are available through the public mmc card.h header file. Let's slim down this public mmc interface, as to prevent users from abusing it, by moving some of the functions/definitions to private mmc header files. This change concentrates on moving the functions into private mmc headers, following changes may continue with additional clean-ups. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
* mmc: core: implement enhanced strobe supportShawn Lin2016-07-251-1/+2
| | | | | | | | | | | | | | | | | Controllers use data strobe line to latch data from devices under hs400 mode, but not for cmd line. So since emmc 5.1, JEDEC introduces enhanced strobe mode for latching cmd response from emmc devices to host controllers. This new feature is optional, so it depends both on device's cap and host's cap to decide whether to use it or not. Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com> Tested-by: Douglas Anderson <dianders@chromium.org> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: enable MMC/SD/SDIO device to suspend/resume asynchronouslyFu, Zhonghui2015-12-221-0/+2
| | | | | | | | | | | | | | | | | Now, PM core supports asynchronous suspend/resume mode for devices during system suspend/resume, and the power state transition of one device may be completed in separate kernel thread. PM core ensures all power state transition dependency between devices. This patch enables MMC/SD/SDIO card and SDIO function devices to suspend/resume asynchronously. This will take advantage of multicore and improve system suspend/resume speed. After applying this patch and enabling all SDIO function's child devices to suspend/resume asynchronously on ASUS T100TA, the system suspend-to-idle time is reduced from 1645ms to 1108ms, and the system resume time is reduced from 940ms to 918ms. Signed-off-by: Zhonghui Fu <zhonghui.fu@linux.intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* Revert "mmc: core: Convert mmc_driver to device_driver"Ulf Hansson2015-04-171-8/+33
| | | | | | | | | | | | | | | | | | | | This reverts commit 6685ac62b2f0 ("mmc: core: Convert mmc_driver to device_driver") The reverted commit went too far in simplifing the device driver parts for mmc. Let's restore the old mmc_driver to enable driver core to sooner or later to remove the ->probe(), ->remove() and ->shutdown() callbacks from the struct device_driver. Note that, the old ->suspend|resume() callbacks in the struct mmc_driver don't need to be restored, since the mmc block layer has converted to the modern system PM ops. Fixes: 6685ac62b2f0 ("mmc: core: Convert mmc_driver to device_driver") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
* mmc: Add SDIO function devicetree subnode parsingSascha Hauer2015-01-191-0/+4
| | | | | | | | | | | | | | This adds SDIO devicetree subnode parsing to the mmc core. While SDIO devices are runtime probable they sometimes need nonprobable additional information on embedded systems, like an additional gpio interrupt or a clock. This patch makes it possible to supply this information from the devicetree. SDIO drivers will find a pointer to the devicenode in their devices of_node pointer. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> [hdegoede@redhat.com: Misc. cleanups] Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* Merge tag 'pm+acpi-3.19-rc1' of ↵Linus Torvalds2014-12-101-2/+2
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm Pull ACPI and power management updates from Rafael Wysocki: "This time we have some more new material than we used to have during the last couple of development cycles. The most important part of it to me is the introduction of a unified interface for accessing device properties provided by platform firmware. It works with Device Trees and ACPI in a uniform way and drivers using it need not worry about where the properties come from as long as the platform firmware (either DT or ACPI) makes them available. It covers both devices and "bare" device node objects without struct device representation as that turns out to be necessary in some cases. This has been in the works for quite a few months (and development cycles) and has been approved by all of the relevant maintainers. On top of that, some drivers are switched over to the new interface (at25, leds-gpio, gpio_keys_polled) and some additional changes are made to the core GPIO subsystem to allow device drivers to manipulate GPIOs in the "canonical" way on platforms that provide GPIO information in their ACPI tables, but don't assign names to GPIO lines (in which case the driver needs to do that on the basis of what it knows about the device in question). That also has been approved by the GPIO core maintainers and the rfkill driver is now going to use it. Second is support for hardware P-states in the intel_pstate driver. It uses CPUID to detect whether or not the feature is supported by the processor in which case it will be enabled by default. However, it can be disabled entirely from the kernel command line if necessary. Next is support for a platform firmware interface based on ACPI operation regions used by the PMIC (Power Management Integrated Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms. That interface is used for manipulating power resources and for thermal management: sensor temperature reporting, trip point setting and so on. Also the ACPI core is now going to support the _DEP configuration information in a limited way. Basically, _DEP it supposed to reflect off-the-hierarchy dependencies between devices which may be very indirect, like when AML for one device accesses locations in an operation region handled by another device's driver (usually, the device depended on this way is a serial bus or GPIO controller). The support added this time is sufficient to make the ACPI battery driver work on Asus T100A, but it is general enough to be able to cover some other use cases in the future. Finally, we have a new cpufreq driver for the Loongson1B processor. In addition to the above, there are fixes and cleanups all over the place as usual and a traditional ACPICA update to a recent upstream release. As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for Intel platforms should be able to handle power management of the DMA engine correctly, the cpufreq-dt driver should interact with the thermal subsystem in a better way and the ACPI backlight driver should handle some more corner cases, among other things. On top of the ACPICA update there are fixes for race conditions in the ACPICA's interrupt handling code which might lead to some random and strange looking failures on some systems. In the cleanups department the most visible part is the series of commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration option. That was triggered by a discussion regarding the generic power domains code during which we realized that trying to support certain combinations of PM config options was painful and not really worth it, because nobody would use them in production anyway. For this reason, we decided to make CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the conclusion that the latter became redundant and CONFIG_PM could be used instead of it. The material here makes that replacement in a major part of the tree, but there will be at least one more batch of that in the second part of the merge window. Specifics: - Support for retrieving device properties information from ACPI _DSD device configuration objects and a unified device properties interface for device drivers (and subsystems) on top of that. As stated above, this works with Device Trees and ACPI and allows device drivers to be written in a platform firmware (DT or ACPI) agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are now going to use this new interface and the GPIO subsystem is additionally modified to allow device drivers to assign names to GPIO resources returned by ACPI _CRS objects (in case _DSD is not present or does not provide the expected data). The changes in this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam, Geert Uytterhoeven). - Support for Hardware Managed Performance States (HWP) as described in Volume 3, section 14.4, of the Intel SDM in the intel_pstate driver. CPUID is used to detect whether or not the feature is supported by the processor. If supported, it will be enabled automatically unless the intel_pstate=no_hwp switch is present in the kernel command line. From Dirk Brandewie. - New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie). - Support for firmware interface based on ACPI operation regions used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR platforms for power resource control and thermal management (Aaron Lu). - Limited support for retrieving off-the-hierarchy dependencies between devices from ACPI _DEP device configuration objects and deferred probing support for the ACPI battery driver based on the _DEP information to make that driver work on Asus T100A (Lan Tianyu). - New cpufreq driver for the Loongson1B processor (Kelvin Cheung). - ACPICA update to upstream revision 20141107 which only affects tools (Bob Moore). - Fixes for race conditions in the ACPICA's interrupt handling code and in the ACPI code related to system suspend and resume (Lv Zheng and Rafael J Wysocki). - ACPI core fix for an RCU-related issue in the ioremap() regions management code that slowed down significantly after CPUs had been allowed to enter idle states even if they'd had RCU callbakcs queued and triggered some problems in certain proprietary graphics driver (and elsewhere). The fix replaces synchronize_rcu() in that code with synchronize_rcu_expedited() which makes the issue go away. From Konstantin Khlebnikov. - ACPI LPSS (Low-Power Subsystem) driver fix to handle power management of the DMA engine included into the LPSS correctly. The problem is that the DMA engine doesn't have ACPI PM support of its own and it simply is turned off when the last LPSS device having ACPI PM support goes into D3cold. To work around that, the PM domain used by the ACPI LPSS driver is redesigned so at least one device with ACPI PM support will be on as long as the DMA engine is in use. From Andy Shevchenko. - ACPI backlight driver fix to avoid using it on "Win8-compatible" systems where it doesn't work and where it was used by default by mistake (Aaron Lu). - Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki, Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin Chaugule (mostly related to the upcoming ARM64 support). - Intel RAPL (Running Average Power Limit) power capping driver fixes and improvements including new processor IDs (Jacob Pan). - Generic power domains modification to power up domains after attaching devices to them to meet the expectations of device drivers and bus types assuming devices to be accessible at probe time (Ulf Hansson). - Preliminary support for controlling device clocks from the generic power domains core code and modifications of the ARM/shmobile platform to use that feature (Ulf Hansson). - Assorted minor fixes and cleanups of the generic power domains core code (Ulf Hansson, Geert Uytterhoeven). - Assorted minor fixes and cleanups of the device clocks control code in the PM core (Geert Uytterhoeven, Grygorii Strashko). - Consolidation of device power management Kconfig options by making CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter which is now redundant (Rafael J Wysocki and Kevin Hilman). That is the first batch of the changes needed for this purpose. - Core device runtime power management support code cleanup related to the execution of callbacks (Andrzej Hajda). - cpuidle ARM support improvements (Lorenzo Pieralisi). - cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and Bartlomiej Zolnierkiewicz). - New cpufreq driver callback (->ready) to be executed when the cpufreq core is ready to use a given policy object and cpufreq-dt driver modification to use that callback for cooling device registration (Viresh Kumar). - cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James Geboski, Tomeu Vizoso). - Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate, cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao, Stefan Wahren, Petr Cvek). - OPP (Operating Performance Points) framework modification to allow OPPs to be removed too and update of a few cpufreq drivers (cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added during initialization) on driver removal (Viresh Kumar). - Hibernation core fixes and cleanups (Tina Ruchandani and Markus Elfring). - PM Kconfig fix related to CPU power management (Pankaj Dubey). - cpupower tool fix (Prarit Bhargava)" * tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits) i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM tools: cpupower: fix return checks for sysfs_get_idlestate_count() drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM leds: leds-gpio: Fix multiple instances registration without 'label' property iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM hwrandom / exynos / PM: Use CONFIG_PM in #ifdef block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM USB / PM: Drop CONFIG_PM_RUNTIME from the USB core PM: Merge the SET*_RUNTIME_PM_OPS() macros ...
| * MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PMRafael J. Wysocki2014-12-051-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | After commit b2b49ccbdd54 (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks depending on CONFIG_PM_RUNTIME may now be changed to depend on CONFIG_PM. Replace CONFIG_PM_RUNTIME with CONFIG_PM everywhere under drivers/mmc/. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
* | mmc: core: Convert mmc_driver to device_driverUlf Hansson2014-11-101-33/+8
| | | | | | | | | | | | | | | | | | | | | | The struct mmc_driver adds an extra layer on top of the struct device_driver. That would be fine, if there were a good reason, but that's not the case. Let's simplify code by converting to the common struct device_driver instead and thus also removing superfluous overhead. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* | mmc: core: Convert the mmc_driver to use the modern PM opsUlf Hansson2014-11-101-10/+4
|/ | | | | | | Instead of having specific mmc system PM callbacks for the mmc driver, let's convert to use the common ones. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
* mmc: core: Remove redundant runtime_idle callbackUlf Hansson2014-07-091-9/+1
| | | | | | | | The runtime PM core handles a runtime_idle callback set to NULL as one returning 0. So, let's just set it to NULL instead. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
* mmc: add support for HS400 mode of eMMC5.0Seungwon Jeon2014-05-121-0/+1
| | | | | | | | | | | | | | | This patch adds HS400 mode support for eMMC5.0 device. HS400 mode is high speed DDR interface timing from HS200. Clock frequency is up to 200MHz and only 8-bit bus width is supported. In addition, tuning process of HS200 is required to synchronize the command response on the CMD line because CMD input timing for HS400 mode is the same as HS200 mode. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Reviewed-by: Jackey Shen <jackey.shen@amd.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: drop the speed mode of card's stateSeungwon Jeon2014-05-121-4/+4
| | | | | | | | | | | Timing mode identifier has same role and can take the place of speed mode. This change removes all related speed mode. Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* mmc: core: Remove unnecessary validations for bus_ops callbacksUlf Hansson2014-02-131-10/+2
| | | | | | | | | Due to the removal of the Kconfig option MMC_UNSAFE_RESUME, several validations of a present bus_ops callback became redundant. Let's remove these. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <chris@printf.net>
* Merge tag 'mmc-updates-for-3.13-rc1' of ↵Linus Torvalds2013-11-181-1/+1
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc Pull MMC updates from Chris Ball: "MMC highlights for 3.13: Core: - Improve runtime PM support, remove mmc_{suspend,resume}_host(). - Add MMC_CAP_RUNTIME_RESUME, for delaying MMC resume until we're outside of the resume sequence (in runtime_resume) to decrease system resume time. Drivers: - dw_mmc: Support HS200 mode. - sdhci-eshdc-imx: Support SD3.0 SDR clock tuning, DDR on IMX6. - sdhci-pci: Add support for Intel Clovertrail and Merrifield" * tag 'mmc-updates-for-3.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (108 commits) mmc: wbsd: Silence compiler warning mmc: core: Silence compiler warning in __mmc_switch mmc: sh_mmcif: Convert to clk_prepare|unprepare mmc: sh_mmcif: Convert to PM macros when defining dev_pm_ops mmc: dw_mmc: exynos: Revert the sdr_timing assignment mmc: sdhci: Avoid needless loop while handling SDIO interrupts in sdhci_irq mmc: core: Add MMC_CAP_RUNTIME_RESUME to resume at runtime_resume mmc: core: Improve runtime PM support during suspend/resume for sd/mmc mmc: core: Remove redundant mmc_power_up|off at runtime callbacks mmc: Don't force card to active state when entering suspend/shutdown MIPS: db1235: Don't use MMC_CLKGATE mmc: core: Remove deprecated mmc_suspend|resume_host APIs mmc: mmci: Move away from using deprecated APIs mmc: via-sdmmc: Move away from using deprecated APIs mmc: tmio: Move away from using deprecated APIs mmc: sh_mmcif: Move away from using deprecated APIs mmc: sdricoh_cs: Move away from using deprecated APIs mmc: rtsx: Remove redundant suspend and resume callbacks mmc: wbsd: Move away from using deprecated APIs mmc: pxamci: Remove redundant suspend and resume callbacks ...
| * mmc: core: clean up duplicate macrosJackey Shen2013-09-251-1/+1
| | | | | | | | | | | | | | | | | | Clean up the duplicate macros: mmc_sd_card_uhs -> mmc_card_uhs mmc_sd_card_set_uhs -> mmc_card_set_uhs Signed-off-by: Jackey Shen <jackey.shen@amd.com> Signed-off-by: Chris Ball <cjb@laptop.org>
* | MMC: convert bus code to use dev_groupsGreg Kroah-Hartman2013-10-161-5/+7
|/ | | | | | | | | | | | | The dev_attrs field of struct bus_type is going away soon, dev_groups should be used instead. This converts the MMC bus code to use the correct field. Cc: Chris Ball <cjb@laptop.org> Cc: Ulf Hansson <ulf.hansson@linaro.org> Cc: Konstantin Dorfman <kdorfman@codeaurora.org> Cc: Seungwon Jeon <tgih.jun@samsung.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* Merge tag 'mmc-updates-for-3.11-rc1' of ↵Linus Torvalds2013-07-101-5/+47
|\ | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc Pull MMC updates from Chris Ball: "MMC highlights for 3.11: Core: - Add support for eMMC 5.1 devices - Add MMC_CAP_AGGRESSIVE_PM capability for aggressive power management of eMMC/SD between requests, using runtime PM - Add an ioctl to perform the eMMC 4.5 Sanitize command. Sample code at: git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc-utils.git Drivers: - dw_mmc: Add support for Rockchip's Cortex-A9 SoCs - dw_mmc: Add support for Altera SoCFPGAs - sdhci-esdhc-imx: Add support for 8-bit bus width, non-removable cards - sdhci-bcm-kona: New driver for Broadcom Kona (281xx) SoCs - sdhi/tmio: Add DT DMA support" * tag 'mmc-updates-for-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (87 commits) mmc: bcm281xx SDHCI driver mmc: sdhci: add card_event callback to sdhci mmc: core: Fixup Oops for SDIO shutdown mmc: sdhci-pci: add another device id mmc: esdhc: Fix bug when writing to SDHCI_HOST_CONTROL register mmc: esdhc: Add support for 8-bit bus width and non-removable card mmc: core: production year for eMMC 4.41 and later mmc: omap: remove unnecessary #if 0's mmc: sdhci: fix ctrl_2 on super-speed selection mmc: dw_mmc-pltfm: add Rockchip variant mmc: dw_mmc-pltfm: move probe and remove below dt match table mmc: dw_mmc-pltfm: remove static from dw_mci_pltfm_remove mmc: sdhci-acpi: add support for eMMC hardware reset for HID 80860F14 mmc: sdhci-pci: add support for eMMC hardware reset for BYT eMMC. mmc: dw_mmc: Add support DW SD/MMC driver on SOCFPGA mmc: sdhci: fix caps2 for HS200 sdhci-pxav3: Fix runtime PM initialization mmc: core: Add DT-bindings for MMC_CAP2_FULL_PWR_CYCLE mmc: core: Invent MMC_CAP2_FULL_PWR_CYCLE mmc: core: Enable power_off_notify for eMMC shutdown sequence ...
| * mmc: core: Fixup Oops for SDIO shutdownUlf Hansson2013-07-051-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Commit "mmc: core: Handle card shutdown from mmc_bus" introduced an Oops in the shutdown sequence for SDIO. The drv pointer, does not exist for SDIO since the probing of the SDIO card from the mmc_bus perspective is expected to fail by returning -ENODEV. This patch adds the proper check for the pointer before calling it. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Reported-by: Stephen Warren <swarren@wwwdotorg.org> Reported-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com> Tested-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com> Acked-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: core: Extend shutdown sequence to handle bus operationsUlf Hansson2013-06-271-0/+9
| | | | | | | | | | | | | | | | | | By adding an optional .shutdown callback to the bus_ops struct we provide the possibility to let each bus type handle it's shutdown requirements. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: core: Handle card shutdown from mmc_busUlf Hansson2013-06-271-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | Considering shutdown of the card, the responsibility to initate this sequence shall be driven from the mmc_bus. This patch enables the mmc_bus to handle this sequence properly. A new .shutdown callback is added in the mmc_driver struct which is used to shutdown the blk device. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: core: Initiate suspend|resume from mmc bus instead of mmc hostUlf Hansson2013-06-271-3/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The host should be responsible to suspend|resume the host and not the card. This patch changes this behaviour, by moving the responsiblity to the mmc bus instead which already holds the card device. The exported functions mmc_suspend|resume_host are now to be considered as depcrecated. Once all host drivers moves away from using them, we can remove them. As of now, a successful error code is always returned. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Tested-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
| * mmc: core: Add bus_ops for runtime pm callbacksUlf Hansson2013-05-261-2/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SDIO is the only protocol that uses runtime pm for the card device right now. To provide the option for sd and mmc to use runtime pm as well the bus_ops callback are extended with two new functions. One for runtime_suspend and one for runtime_resume. This patch will also implement the callbacks for SDIO to make sure existing functionality is maintained. It also prepares to move away from using the mmc_power_restore_host API, since it is not needed when using runtime PM. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
* | PM / Runtime: Rework the "runtime idle" helper routineRafael J. Wysocki2013-06-031-1/+1
|/ | | | | | | | | | | | | | | | | | | | | | | | | | The "runtime idle" helper routine, rpm_idle(), currently ignores return values from .runtime_idle() callbacks executed by it. However, it turns out that many subsystems use pm_generic_runtime_idle() which checks the return value of the driver's callback and executes pm_runtime_suspend() for the device unless that value is not 0. If that logic is moved to rpm_idle() instead, pm_generic_runtime_idle() can be dropped and its users will not need any .runtime_idle() callbacks any more. Moreover, the PCI, SCSI, and SATA subsystems' .runtime_idle() routines, pci_pm_runtime_idle(), scsi_runtime_idle(), and ata_port_runtime_idle(), respectively, as well as a few drivers' ones may be simplified if rpm_idle() calls rpm_suspend() after 0 has been returned by the .runtime_idle() callback executed by it. To reduce overall code bloat, make the changes described above. Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com> Tested-by: Kevin Hilman <khilman@linaro.org> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Kevin Hilman <khilman@linaro.org> Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Alan Stern <stern@rowland.harvard.edu>
* mmc: fix async request mechanism for sequential read scenariosKonstantin Dorfman2013-02-111-0/+1
| | | | | | | | | | | | | | | | | | | | | When current request is running on the bus and if next request fetched by mmcqd is NULL, mmc context (mmcqd thread) gets blocked until the current request completes. This means that if new request comes in while the mmcqd thread is blocked, this new request can not be prepared in parallel to current ongoing request. This may result in delaying the new request execution and increase it's latency. This change allows to wake up the MMC thread on new request arrival. Now once the MMC thread is woken up, a new request can be fetched and prepared in parallel to the current running request which means this new request can be started immediately after the current running request completes. With this change read throughput is improved by 16%. Signed-off-by: Konstantin Dorfman <kdorfman@codeaurora.org> Reviewed-by: Seungwon Jeon <tgih.jun@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
* mmc: Remove redundant null check before kfree in bus.cSachin Kamat2012-12-061-2/+1
| | | | | | | kfree on a null pointer is a no-op. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
* mmc: core: check PM_SLEEP for mmc_bus_suspend/resume callbacksChuanxiao Dong2012-04-231-0/+2
| | | | | | | | | | If PM_SLEEP is not enabled, mmc.c will give warnning since mmc_bus_suspend/ mmc_bus_resume functions are defined but not used. This patch can fix this warnning. Reported-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
* mmc: remove MMC bus legacy suspend/resume methodChuanxiao Dong2012-04-201-16/+8
| | | | | | | | | | | | | | | | MMC bus is using legacy suspend/resume method, which is not compatible if runtime pm callbacks are used. In this scenario, MMC bus suspend/resume callbacks cannot be called when system entering S3. So change to use the new defined dev_pm_ops for system sleeping mode. Tested on AM335x Platform. Solves major issue/crash reported at http://www.mail-archive.com/linux-omap@vger.kernel.org/msg65425.html Signed-off-by: Chuanxiao Dong <chuanxiao.dong@intel.com> Tested-by: Hebbar, Gururaja <gururaja.hebbar@ti.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Ulf Hansson <ulf.hansson@stericsson.com> Signed-off-by: Chris Ball <cjb@laptop.org>
* mmc: bus: print bus speed mode of UHS-I cardSubhash Jadavani2012-04-051-2/+15
| | | | | | | | | | When UHS-I card is detected also print the bus speed mode in which UHS-I card will be running. Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org> Reviewed-by: Namjae Jeon <linkinjeon@gmail.com> Acked-by: Aaron Lu <aaron.lu@amd.com> Signed-off-by: Chris Ball <cjb@laptop.org>
* mmc: core: HS200 mode support for eMMC 4.5Girish K S2012-01-121-1/+2
| | | | | | | | | | | This patch adds the support of the HS200 bus speed for eMMC 4.5 devices. The eMMC 4.5 devices have support for 200MHz bus speed. The function prototype of the tuning function is modified to handle the tuning command number which is different in sd and mmc case. Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Signed-off-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
* mmc: sdio: support SDIO UHS cardsPhilip Rakity2012-01-111-1/+1
| | | | | | | | | | | | | | | | | | | This patch adds support for sdio UHS cards per the version 3.0 spec. UHS mode is only enabled for version 3.0 cards when both the host and the controller support UHS modes. 1.8v signaling support is removed if both the card and the host do not support UHS. This is done to maintain compatibility and some system/card combinations break when 1.8v signaling is enabled when the host does not support UHS. Signed-off-by: Philip Rakity <prakity@marvell.com> Signed-off-by: Aaron Lu <Aaron.lu@amd.com> Reviewed-by: Arindam Nath <arindam.nath@amd.com> Tested-by: Bing Zhao <bzhao@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
* mmc: Fix implicit use of stat.h header in associated filesPaul Gortmaker2011-10-311-0/+1
| | | | | | | | | Once the implicit use of module.h is prevented, these files will fail to find the stat.h header content. Fix up the implicit usage expectations in advance of the cleanup. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* mmc: Add export.h for EXPORT_SYMBOL/THIS_MODULE as requiredPaul Gortmaker2011-10-311-0/+1
| | | | | | | | These two basic defines were everywhere, simply because module.h was also everywhere. But we are cleaning up the latter. So make the exporters actually call out their need for the include. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
* mmc: replace printk with appropriate display macroGirish K S2011-10-261-3/+3
| | | | | | | | All the files using printk function for displaying kernel messages in the mmc driver have been replaced with corresponding macro. Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
* mmc: sd: report correct speed and capacity of uhs cardsArindam Nath2011-05-241-3/+8
| | | | | | | | | | | | | | | | | Since only UHS-I cards respond with S18A set in response to ACMD41, we set the card as ultra-high-speed after successfull initialization. We need to decide whether a card is SDXC based on the C_SIZE field of CSDv2.0 register. According to Physical Layer spec v3.01, the minimum value of C_SIZE for SDXC card is 00FFFFh. Tested by Zhangfei Gao with a Toshiba uhs card and general hs card, on mmp2 in SDMA mode. Signed-off-by: Arindam Nath <arindam.nath@amd.com> Reviewed-by: Philip Rakity <prakity@marvell.com> Tested-by: Philip Rakity <prakity@marvell.com> Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com> Signed-off-by: Chris Ball <cjb@laptop.org>
* mmc: core: mmc_add_card(): fix missing break in switch statementMichał Mirosław2011-04-271-0/+1
| | | | | | | | Fixes a cosmetic bug that affects printk() for SD-combo cards. Reported-by: Prashanth Bhat <prashanth.bhat@manipal.net> Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Chris Ball <cjb@laptop.org>