1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
|
# Configuration file for the Gigabyte GA-880GA-UD3H,
# contributed by Clipo.
# 2019-02-14
# Updates welcome.
#
# Based on Gigabyte GA-870A-UD3.conf contributed by Gary Myers and Zeke Fast
#
#
# CPU sensor
chip "k10temp-*"
label temp1 "CPU Temp (K10)"
# Motherboard sensors
chip "it8720-isa-*"
### Voltages
label in0 "Vcore"
label in1 "DDR3 1.5V" # as labelled in the BIOS.
label in2 "+3.3V"
label in3 "+5V" # Not shown in BIOS.
label in4 "+12V" # Not shown in BIOS
ignore in5 # Ambiguous - ignoring.
ignore in6 # Ambiguous - ignoring.
label in7 "5VSB" # Not shown in BIOS.
label in8 "Vbat" # Not shown in BIOS.
ignore cpu0_vid
# "Vcore", "DDR3 1.5V", "+3.3V" and "Vbat" are connected directly, so no compute
# line is needed for these. +5V and 5VSB are internal so we use the
# standard scaling factor. Scaling for +12V is apparently not standard
# this value was taken from the donor config file
#
compute in3 @ * (6.8/10+1), @ / (6.8/10+1)
compute in4 @ * 3.963, @ / 3.963
compute in7 @ * (6.8/10+1), @ / (6.8/10+1)
# The BIOS will not set any limit for voltages.
set in0_min 0.825 * 0.95
set in0_max 1.425 * 1.05
set in1_min 1.5 * 0.95
set in1_max 1.5 * 1.05
set in2_min 3.3 * 0.95
set in2_max 3.3 * 1.05
set in3_min 5 * 0.95
set in3_max 5 * 1.05
set in4_min 12 * 0.95
set in4_max 12 * 1.05
set in7_min 5 * 0.95
set in7_max 5 * 1.05
### Temperatures
label temp1 "System Temp"
# This sensor appears to be around or inside the ITE8720F chip.
set temp1_min 0
set temp1_max 40
label temp2 "CPU Temp"
# This sensor can show 2 degrees difference to the K10 sensor.
# The end user can choose which one they prefer.
set temp2_min 0
set temp2_max 60 # Set to match your BIOS "CPU Warning Temperature"
label temp3 "Second CPU Temp?"
#This sensors appears to follow the CPU temp but with a large termal lag and slightly lower value
#
#set temp3 #
### Fans
# Label based on motherboard connectors.
label fan1 "CPU Fan" # M/B label: CPU_FAN (4-pin)
label fan5 "Power Fan" # M/B label: PWR_FAN (3-pin)
label fan2 "System Fan 1" # M/B label: SYS_FAN1 (3-pin)
label fan3 "System Fan 2" # M/B label: SYS_FAN2 (3-pin)
# Minimum fan speeds.
# Comment/un-comment fan headers you are using if you want alarms.
set fan1_min 300 # CPU Fan
set fan5_min 300 # Power Fan
set fan2_min 300 # System Fan 1
set fan3_min 300 # System Fan 2
# Original Sensors output before configuration applied
#
## it8720-isa-0228
#Adapter: ISA adapter
#in0: +1.46 V (min = +0.00 V, max = +4.08 V)
#in1: +1.49 V (min = +0.00 V, max = +4.08 V)
#in2: +3.38 V (min = +0.00 V, max = +4.08 V)
#+5V: +3.02 V (min = +0.00 V, max = +4.08 V)
#in4: +3.09 V (min = +0.00 V, max = +4.08 V)
#in5: +2.85 V (min = +0.00 V, max = +4.08 V)
#in6: +4.08 V (min = +0.00 V, max = +4.08 V)
#5VSB: +2.96 V (min = +0.00 V, max = +4.08 V)
#Vbat: +3.02 V
#fan1: 629 RPM (min = 10 RPM)
#fan2: 950 RPM (min = 10 RPM)
#fan3: 1315 RPM (min = 10 RPM)
#fan5: 1310 RPM (min = 10 RPM)
#temp1: +26.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
#temp2: +32.0°C (low = +127.0°C, high = +60.0°C) sensor = thermal diode
#temp3: +34.0°C (low = +127.0°C, high = +127.0°C) sensor = thermistor
#cpu0_vid: +0.513 V
#intrusion0: ALARM
#
#k10temp-pci-00c3
#Adapter: PCI adapter
#temp1: +32.9°C (high = +70.0°C)
# (crit = +79.0°C, hyst = +77.0°C)
|
