summaryrefslogtreecommitdiff
Commit message (Collapse)AuthorAgeFilesLines
* misc-utils: flashcp: correct casting for percent displayHEADmastercchoux2023-04-241-2/+2
| | | | | | | | | Add correct casting for written to prevent overflow that size_t is only 32 bits on a 32-bit platform. Signed-off-by: cchoux <chou.cosmo@gmail.com> Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* mtd-utils: flash_speed: Measure read while write latencyMiquel Raynal2022-11-182-4/+127
| | | | | | | | | | | | | | | | | | | | | | | | | The Read While Write (RWW) feature allows to perform reads from the flash array into cache while a program (from cache) or an erase operation happens, provided that the two areas are located on different banks. The main benefit is the possible reduced latency when requesting to read a page while a much longer operation is ongoing, like a write or an erase. We can try to compare the positive impact of such a feature by enhancing the flash_speed test tool with the following test: - Measure the time taken by an eraseblock write in parallel with an eraseblock read. - Measure when the read operation ends. - Compare the two to get the latency saved with the RWW feature. To be sure the mtd_write actually starts (and acquires the necessary locks) before the mtd_read does, we use SCHED_FIFO at rather high (arbitrary) priorities, respectively 42 and 41. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* mtd-utils: flash_speed: Rework the time counting helpersMiquel Raynal2022-11-181-16/+23
| | | | | | | | | | In order to be able to have interleaved measures, let's not use the start and finish global variables from the time helpers directly, provide parameters for these variables so that we can provide either the global entries, or more specific ones when relevant. Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* misc-utils: mtdpart: document partition of size 0Brandon Maier2022-11-071-1/+1
| | | | | | | | | | | If the partition size passed in to the BLKPG_ADD_PARTITION ioctl is 0, Linux will make the partition fill to the end of the device[1]. Document this feature in the help. [1] https://elixir.bootlin.com/linux/v6.0.6/source/drivers/mtd/mtdpart.c#L254 Signed-off-by: Brandon Maier <brandon.maier@collins.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* misc-utils: flashcp: abort on --partition and --erase-allBrandon Maier2022-11-071-0/+3
| | | | | Signed-off-by: Brandon Maier <brandon.maier@collins.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* misc-utils: flashcp: verify data in --partitionBrandon Maier2022-11-071-0/+9
| | | | | | | | The --partition mode is not verifying that data is being written successfully. Signed-off-by: Brandon Maier <brandon.maier@collins.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* misc-utils: flashcp: fix buffer overflowBrandon Maier2022-11-071-8/+13
| | | | | | | | | | | | | | The DIFF_BLOCKS code requires that src and dest buffers be large enough to hold one MTD erasesize. This is because each loop operates on one eraseblock so that it can erase and write one whole sector. But the src and dest buffers are fixed at BUFSIZE, so on platforms where the MTD erasesize are larger then BUFSIZE it will overflow the buffers. Instead allocate the buffers dynamically so that they can be sized to fit the erasesize. Signed-off-by: Brandon Maier <brandon.maier@collins.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* misc-utils: flashcp: simplify loggingBrandon Maier2022-11-071-96/+77
| | | | | | | | | | | | | | | | | Most of the uses of log_printf fall into two styles > if (flags & FLAG_VERBOSE) > log_printf(LOG_NORMAL, ...); or > log_printf(LOG_ERROR, ...) > exit(EXIT_FAILURE); Replace them with log_verbose and log_failure respectively. Signed-off-by: Brandon Maier <brandon.maier@collins.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* misc-utils: flashcp: add safe_memeraseBrandon Maier2022-11-071-23/+15
| | | | | Signed-off-by: Brandon Maier <brandon.maier@collins.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* misc-utils: flashcp: check for lseek errorsBrandon Maier2022-11-071-6/+16
| | | | | | | Add a safe_lseek wrapper to check for lseek errors. Signed-off-by: Brandon Maier <brandon.maier@collins.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* misc-utils: flashcp: add safe_writeBrandon Maier2022-11-071-33/+25
| | | | | | | Share the writing code between the two write implementations. Signed-off-by: Brandon Maier <brandon.maier@collins.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* Release mtd-utils-2.1.5v2.1.5David Oberhollenzer2022-10-071-1/+1
| | | | Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* Fix warning about unaligned pointer in jffs2readerFrederic Germain2022-10-071-2/+3
| | | | | | | | | | gcc 9.3.0-17ubuntu1~20.04 warning on time_t ctime value is : Fix taking address of packed member of ‘struct jffs2_raw_inode’ may result in an unaligned pointer value [-Waddress-of-packed-member]. Signed-off-by: Frederic Germain <frederic.germain@gmail.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* .gitignore: add new ubiscan utilityFrederic Germain2022-10-071-0/+1
| | | | | Signed-off-by: Frederic Germain <frederic.germain@gmail.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* nor-utils: fix memory leakliaohua2022-10-041-1/+1
| | | | | | | | This patch replace "free(rfd.sector_map)" with "free(rfd.header)" to fix memory leak. Signed-off-by: liaohua <liaohua4@huawei.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* libmtd: do not ignore non-zero eraseblock size when MTD_NO_ERASE is setEnrico Jorns2022-09-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In 54d68799, mtd->eb_cnt was enforced to be '1' if MTD_NO_ERASE is set. This was done with the aim of preventing divisions by zero. However, even if MTD_NO_ERASE is set, mtd->eb_size (eraseblock size) can still be set to a non-zero value which would not cause a division by zero. Instead, enforcing an eraseblock count of '1' here even leads to inconsistent eraseblock counting in mtd-utils and lets for example a 'flash_erase' on an mtdnand device fail: | # flash_erase /dev/mtd0 0 0 | Erasing 32768 Kibyte @ 0 -- 0 % complete libmtd: error!: bad eraseblock number 255, mtd0 has 1 eraseblocks | flash_erase: error!: /dev/mtd0: MTD Erase entire chip failureTrying one by one each sector. | error 22 (Invalid argument) | Erasing 128 Kibyte @ 0 -- 0 % complete libmtd: error!: bad eraseblock number 1, mtd0 has 1 eraseblocks | flash_erase: error!: /dev/mtd0: MTD get bad block failed | error 22 (Invalid argument) Also mtdinfo would look inconsistent (eraseblock size vs amount): | # mtdinfo /dev/mtd0 | mtd0 | Name: mtdram test device | Type: ram | Eraseblock size: 131072 bytes, 128.0 KiB | Amount of eraseblocks: 1 (33554432 bytes, 32.0 MiB) | Minimum input/output unit size: 1 byte | Sub-page size: 1 byte | Character device major/minor: 90:0 | Bad blocks are allowed: false | Device is writable: true Fix this by enforcing mtd->eb_cnt to be '1' only when mtd->eb_size is actually zero and would lead to a division by zero otherwise. Fixes: 54d68799 ("libmtd: avoid divide by zero") Signed-off-by: Enrico Jorns <ejo@pengutronix.de> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* mtd-utils: flash_otp_dump make offset optionalMichael Walle2022-09-271-1/+1
| | | | | | | | | | | | Commit 0a5e2fa5c1e4 ("mtd-utils: add optional offset parameter to flash_otp_dump") introduced an offset parameter. This should have been optional, but there was a typo. Fix it. Reported-by: Sergei Antonov <saproj@gmail.com> Fixes: 0a5e2fa5c1e4 ("mtd-utils: add optional offset parameter to flash_otp_dump") Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Sergei Antonov <saproj@gmail.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* mkfs.jffs2: fix spelling of --compression-mode parameter in help textAlex Henrie2022-09-271-1/+2
| | | | | | | --compr-mode is not accepted as an alias of --compression-mode. Signed-off-by: Alex Henrie <alexhenrie24@gmail.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* tests: Remove unused linux/fs.h header from includesKhem Raj2022-08-081-1/+0
| | | | | | | | | | This header is not needed, moreover it includes linux/mount.h which is now in conflict[1] with glibc provided sys/mount.h from glibc 2.36 onwards [1] https://sourceware.org/glibc/wiki/Release/2.36 Signed-off-by: Khem Raj <raj.khem@gmail.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* nandflipbits: fix corrupted oobChristophe Kerello2022-06-271-1/+3
| | | | | | | | | | If a bit is flipped in block 1 or higher, the OOB is corrupted with the OOB of block 0. Mtd_read_oob API has to take into account the block number to be able to calculate the right offset. Fixes: 9fc8db29cf62 ("mtd-utils: Add nandflipbits tool") Signed-off-by: Christophe Kerello <christophe.kerello@foss.st.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* ubinfo: Fix --vol_id return code for absent volume idAndrew Mellor2022-06-131-6/+3
| | | | | | | | When using --vol_id and that volume is missing, it should return non-zero like the --name option does. Signed-off-by: Andrew Mellor <andrew.mellor@casa-systems.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* mtd-utils: nanddump: fix writing big images on 32bit machinesSascha Hauer2022-06-081-1/+1
| | | | | | | | | | | When writing a full 4GiB NAND to a file end_addr becomes 0x100000000. With that writing out the first page to the file doesn't happen because size_left is calculated to 0x100000000 - 0 = 0x100000000 which is then truncated to 32bit and becomes zero. Fix this by using an appropriate 64bit type for size_left. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* nandwrite: warn about writing 0xff blocksRafał Miłecki2022-03-281-1/+12
| | | | | | | | | Such blocks may be incorrectly treated as empty (even though they may have non-erase OOB). Warn about it so people may start useing --skip-all-ffs . Signed-off-by: Rafał Miłecki <rafal@milecki.pl> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* fix test bashismMike Frysinger2022-01-171-3/+3
| | | | | | | Using == with `test` is a bashism. POSIX shell only supports =. Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* Release mtd-utils-2.1.4v2.1.4David Oberhollenzer2022-01-061-1/+1
| | | | Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* Fix: add missing new-line-escape in jffsX-utils Makemodule.amDavid Oberhollenzer2022-01-051-1/+1
| | | | | | | | | | | | | | | In commit a888044525, various header files that were added to the distribution tarball via EXTRA_DIST were instead added to the source lists of their respective programs instead. In the case of jffsX-utils, a missing escape for a new-line in the source list caused the include/linux/jffs2.h header to not be packged in the release tarball. This went undiscovered, as the system on which the release tarball was built, had the same header installed installed in the system include directory, so a `make distcheck` succeeded. Fixes: a888044525 Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* fectest.c: fix buffer overrunRalph Siemsen2021-12-061-1/+1
| | | | | | | | | misc-utils/fectest.c:37:11: warning: iteration 47 invokes undefined behavior [-Waggressive-loop-optimizations] 37 | srcs[i] = buf + (i * PKT_SIZE); | ~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~ Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* mtd-tests: use pages during readtest and stressRalph Siemsen2021-12-062-2/+2
| | | | | | | | | | | | Same fix as a2c6bbc ("mtd-tests: Read and write pages during speed tests") but applied to flash_readtest and flash_stress. Resolves failure of flash_readtest when subpages are present. The test reads a (sub)page followed by the entire OOB. Upon reaching the 2nd subpage, the OOB read fails because it is beyond the end of OOB. Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* mtd-tests: Read and write pages during speed testsMiquel Raynal2021-10-131-1/+1
| | | | | | | | | | | | | | | | | | | The speed test does reads and writes of different sizes: - eraseblock - page - two pages At least this is the theory because, as opposed to the legacy kernel module doing the same measurement, the userspace tool uses the subpage size (hence accessing the same page 4, 8 or 16 times depending on the subpage setting). Of course if the controller does not support subpages, this issue is not visible. Use mtd.min_io_size instead for non-NOR devices in order to get the right bandwidth (at least one that fits the logs). Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* Add ubiscan utilityDiego Ismirlian2021-09-062-1/+322
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ubiscan will scan the PEBs in a specific MTD device and print a summary of the PEB erase counters and (optionally) details about each PEB's status. Example output: # ./ubiscan /dev/mtd6 Summary ========================================================= mtd : 6 type : nand size : 110362624 bytes (105.2 MiB) PEBs : 842 min I/O: 2048 bytes PEB erase counters ========================================================= valid : 834 empty : 0 corrupted: 0 alien : 0 bad : 8 Histogram ========================================================= from to count min avg max --------------------------------------------------------- 0 .. 9: 55 1 4 9 10 .. 99: 174 10 48 99 100 .. 999: 514 103 287 987 1000 .. 9999: 91 1004 1880 2251 10000 .. 99999: 0 0 0 0 100000 .. inf: 0 0 0 0 --------------------------------------------------------- Total : 834 1 392 2251 If the --verbose switch is given, ubiscan will print PEB details: # ./ubiscan --verbose /dev/mtd6 [... same output as before ...] Details ========================================================= PEB 0: 253 PEB 1: 1489 PEB 2: 1 PEB 3: 1 PEB 4: 1 PEB 5: 1 PEB 6: 1 PEB 7: 1 PEB 8: 1 PEB 9: 1 PEB 10: 1 ... PEB 832: 1225 PEB 833: 252 PEB 834: 111 PEB 835: 298 PEB 836: 1264 PEB 837: 11 PEB 838: EB_BAD PEB 839: EB_BAD PEB 840: EB_BAD PEB 841: EB_BAD Signed-off-by: Diego Ismirlian <dismirlian@gmail.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* Release mtd-utils-2.1.3v2.1.3David Oberhollenzer2021-07-251-1/+1
| | | | Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* Add missing filljffs2.sh to EXTRA_DISTDavid Oberhollenzer2021-07-251-1/+1
| | | | Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* misc-utils: flashcp: Add new function that copy only different blocksHarvey Wu2021-06-121-1/+92
| | | | | | | | | | | | - The original flashcp process is erase, write and verify all blocks in one time from file to device. This patch will add a function that only copy different block data from file to device. The function will compare blocks by block between file and device, then erase and write block data from file to device if found different block. Signed-off-by: Harvey Wu <harveywu95@gmail.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* mtd-utils: Add flash_otp_eraseMichael Walle2021-06-124-1/+70
| | | | | | | | On some SPI NOR flashes you can actually erase the OTP region until its fully locked. Add a small utility for that. Signed-off-by: Michael Walle <michael@walle.cc> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* mtd-utils: flash_erase: Add flash erase chipLarisa Ileana Grigore2021-05-053-30/+106
| | | | | | | | | Some flash types support full erase chip command which can reduce the flash erase time. Try first to erase the entire flash and fall back to the old method if the operation fails. Signed-off-by: Larisa Ileana Grigore <larisa.grigore@nxp.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* mkfs.ubifs: Fix runtime assertions when running without cryptoHenri Roosen2021-03-221-2/+2
| | | | | | | | | | | | | | | | | Running mkfs.ubifs which was build without crypto triggered the following assertion: mkfs.ubifs: ubifs-utils/mkfs.ubifs/fscrypt.h:166: inherit_fscrypt_context: Assertion `0' failed. A previous commit-cc4c5e295f54 ("mkfs.ubifs: Enable support for building without crypto") added a check for an existing fscrypt context before calling functions inherit_fscrypt_context() and free_fscrypt_context(), however did not properly do this for each call to these functions. Fixes: cc4c5e295f54 ("mkfs.ubifs: Enable support for building without crypto") Signed-off-by: Henri Roosen <henri.roosen@ginzinger.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* mtd-utils: Use AC_SYS_LARGEFILESascha Hauer2021-02-284-6/+3
| | | | | | | | | | | | Currently mtd-utils on 32bit systems fail on devices >2GiB due to off_t being a signed 32bit type. Add AC_SYS_LARGEFILE to make off_t a 64bit type. Adding AC_SYS_LARGEFILE results in _FILE_OFFSET_BITS being defined to 64 in include/config.h. To let this have an effect we must make sure that include/config.h is included before all other includes which is archieved by adding its inclusion to CPPFLAGS. Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* Fix test binary installationDavid Oberhollenzer2021-01-2015-98/+56
| | | | | | | | | | - Remove "install tests" configure option, we already have an option whether to build tests or not. Don't try to work around autotools semantics that people building the package expect. - Fix the installation path by propperly defining it and using the correct name for the libexec path. Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* Cleanup: Automake: remove single use variablesDavid Oberhollenzer2021-01-2010-64/+18
| | | | | | | | | | | | | | Throughout the Automake files, there is a consistent pattern somewhat like this: FOO_BINS = .... sbin_PROGRAMS += $(FOO_BINS) This commit all such patterns whenever the variable is not used anywhere else and appends to the target directly. Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* Remove headers from EXTRA_DISTDavid Oberhollenzer2021-01-2012-74/+87
| | | | | | | | | | | This commit removes the C header files from the EXTRA_DIST variables and instead assigns them to the SOURCE variable of the respective components they belong to. This takes care of having them distributed in the release tar ball and helps with dependency tracking a little. Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* libmtd: avoid divide by zeroChris Packham2020-11-291-1/+4
| | | | | | | | | | | The concept of erase blocks doesn't apply to mtd-ram devices. Such devices set MTD_NO_ERASE to indicate this and some report 0 for the erase block size. Avoid a divide by zero when calculating the erase block count for such devices. Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz> Acked-by: Richard Weinberger <richard@nod.at> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* mtd-utils: ubihealthd: this tool does not depend on UBIFSJuergen Borleis2020-11-291-2/+4
| | | | | | | | | | | | | | | | | The "need_getrandom" check and result is used only for the "ubihealthd". This tool is very important to have it around at run-time, while the corresponding "mkfs.ubifs" tool is still optional (think about offline generated ubifs images). Since compiling "mkfs.ubifs" adds more dependencies (various shared libraries), buildsystems for embedded devices will add these shared libraries to the root filesystem even if "mkfs.ubifs" isn't used or installed. Thus, handling both tools independently makes sense. The previous behavior is kept, e.g. if UBIFS support is enabled, it enables "ubihealthd" as well. Signed-off-by: Juergen Borleis <jbe@pengutronix.de> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* Add an ubifs mount helperUwe Kleine-König2020-11-182-0/+103
| | | | | | | | | | | | | This abstracts away attaching of the right ubi and then selecting the right ubi device and volume to mount. As described in the comment at the top this allows to mount ubifs volumes directly from /etc/fstab without having to use hardcoded numbers (which depend on mount order and so are unreliable) and extra magic to care for attaching. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* mkfs.ubifs: remove OPENSSL_no_config()Torben Hohn2020-10-181-1/+2
| | | | | | | | | | | | | | Especially for the pkcs11 engine, a configuration is required because the provider has to be configured. Its not clear why OPENSSL_no_config() is called. Remove OPENSSL_no_config() and call OPENSSL_config(NULL) instead. Signed-off-by: Torben Hohn <torben.hohn@linutronix.de> Signed-off-by: Bastian Germann <bage@linutronix.de> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* mtd-utils: Add nandflipbits toolBoris Brezillon2020-10-183-1/+328
| | | | | | | | | | | | | | | | | | | | | | | | | The nandflipbits tool is intended to be used when one need to flip one or several specific bits on a NAND media. It can be useful to manually recover from an unexpected bit flip on a flash device, though the main purpose of this tool is to provide a way to test ECC algorithms robustness. One typical example I used this tool for is testing HW ECC engines behavior when bitflips occur in an erased page: most HW engines do not correctly handle this case, because, most of the time, ECC bits generated for an empty page are not all 1s, and, empty page detection embedded in such engines is only validating that all bits are set to 1s (which is not true when a bit-flip has occurred). Another use of this tool is replacing nandbiterrs test which absolutely do not work with MLC-like chips because of the rewriting of the pages in raw mode to toggle ones into zeroes. Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com> [miquel: Took Boris' work from 2014, addressed comments from Brian made in 2015, updated it, tested more extensively and fixed issues] Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* misc-utils: Add fectest to build systemBastian Germann2020-09-292-1/+5
| | | | | | | | 8f627247f6("mtd-utils: move libmtd source files to lib/ subdirectory") removed fectest.c from the build system 10 years ago. Add it again. Signed-off-by: Bastian Germann <bastiangermann@fishpost.de> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* mkfs.ubifs: Fix build with SELinuxBastian Germann2020-09-231-9/+1
| | | | | | | | | | | | In v2.1.0, SELinux support was introduced. It never compiled with ubifs because it uses the old add_xattr signature that also changed in v2.1.0 with a1bd316e23("mkfs.ubifs: Implement fscrypto context store as xattr"). Add the ubifs_ino_node and name to the call and remove the nm that is contructed in the new function version. Signed-off-by: Bastian Germann <bastiangermann@fishpost.de> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* Fix typos found by Debian's lintian toolBastian Germann2020-09-117-11/+11
| | | | | Signed-off-by: Bastian Germann <bastiangermann@fishpost.de> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* fix build of jffs2reader and jffs2dump if zlib or lzo headers are not in ↵Rolf Eike Beer2020-07-311-0/+2
| | | | | | | default paths Signed-off-by: Rolf Eike Beer <eb@emlix.com> Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
* Release mtd-utils-2.1.2v2.1.2David Oberhollenzer2020-07-131-1/+1
| | | | Signed-off-by: David Oberhollenzer <david.oberhollenzer@sigma-star.at>
View Lorry Controller Status