1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
|
=pod
=head1 NAME
BIO_socket, BIO_bind, BIO_connect, BIO_listen, BIO_accept_ex, BIO_closesocket - BIO
socket communication setup routines
=head1 SYNOPSIS
#include <openssl/bio.h>
int BIO_socket(int domain, int socktype, int protocol, int options);
int BIO_bind(int sock, const BIO_ADDR *addr, int options);
int BIO_connect(int sock, const BIO_ADDR *addr, int options);
int BIO_listen(int sock, const BIO_ADDR *addr, int options);
int BIO_accept_ex(int accept_sock, BIO_ADDR *peer, int options);
int BIO_closesocket(int sock);
=head1 DESCRIPTION
BIO_socket() creates a socket in the domain B<domain>, of type
B<socktype> and B<protocol>. Socket B<options> are currently unused,
but is present for future use.
BIO_bind() binds the source address and service to a socket and
may be useful before calling BIO_connect(). The options may include
B<BIO_SOCK_REUSEADDR>, which is described in L</FLAGS> below.
BIO_connect() connects B<sock> to the address and service given by
B<addr>. Connection B<options> may be zero or any combination of
B<BIO_SOCK_KEEPALIVE>, B<BIO_SOCK_NONBLOCK> and B<BIO_SOCK_NODELAY>.
The flags are described in L</FLAGS> below.
BIO_listen() has B<sock> start listening on the address and service
given by B<addr>. Connection B<options> may be zero or any
combination of B<BIO_SOCK_KEEPALIVE>, B<BIO_SOCK_NONBLOCK>,
B<BIO_SOCK_NODELAY>, B<BIO_SOCK_REUSEADDR> and B<BIO_SOCK_V6_ONLY>.
The flags are described in L</FLAGS> below.
BIO_accept_ex() waits for an incoming connections on the given
socket B<accept_sock>. When it gets a connection, the address and
port of the peer gets stored in B<peer> if that one is non-NULL.
Accept B<options> may be zero or B<BIO_SOCK_NONBLOCK>, and is applied
on the accepted socket. The flags are described in L</FLAGS> below.
BIO_closesocket() closes B<sock>.
=head1 FLAGS
=over 4
=item BIO_SOCK_KEEPALIVE
Enables regular sending of keep-alive messages.
=item BIO_SOCK_NONBLOCK
Sets the socket to nonblocking mode.
=item BIO_SOCK_NODELAY
Corresponds to B<TCP_NODELAY>, and disables the Nagle algorithm. With
this set, any data will be sent as soon as possible instead of being
buffered until there's enough for the socket to send out in one go.
=item BIO_SOCK_REUSEADDR
Try to reuse the address and port combination for a recently closed
port.
=item BIO_SOCK_V6_ONLY
When creating an IPv6 socket, make it only listen for IPv6 addresses
and not IPv4 addresses mapped to IPv6.
=item BIO_SOCK_TFO
Enables TCP Fast Open on the socket. Uses appropriate APIs on
supported operating systems, including Linux, macOS and FreeBSD. Can
be used with BIO_connect(), BIO_set_conn_mode(), BIO_set_bind_mode(),
and BIO_listen().
On Linux kernels before 4.14, use BIO_set_conn_address() to specify
the peer address before starting the TLS handshake.
=back
These flags are bit flags, so they are to be combined with the
C<|> operator, for example:
BIO_connect(sock, addr, BIO_SOCK_KEEPALIVE | BIO_SOCK_NONBLOCK);
=head1 RETURN VALUES
BIO_socket() returns the socket number on success or B<INVALID_SOCKET>
(-1) on error. When an error has occurred, the OpenSSL error stack
will hold the error data and errno has the system error.
BIO_bind(), BIO_connect() and BIO_listen() return 1 on success or 0 on error.
When an error has occurred, the OpenSSL error stack will hold the error
data and errno has the system error.
BIO_accept_ex() returns the accepted socket on success or
B<INVALID_SOCKET> (-1) on error. When an error has occurred, the
OpenSSL error stack will hold the error data and errno has the system
error.
=head1 SEE ALSO
L<BIO_ADDR(3)>
=head1 HISTORY
BIO_gethostname(), BIO_get_port(), BIO_get_host_ip(),
BIO_get_accept_socket() and BIO_accept() were deprecated in OpenSSL 1.1.0.
Use the functions described above instead.
=head1 COPYRIGHT
Copyright 2016-2022 The OpenSSL Project Authors. All Rights Reserved.
Licensed under the Apache License 2.0 (the "License"). You may not use
this file except in compliance with the License. You can obtain a copy
in the file LICENSE in the source distribution or at
L<https://www.openssl.org/source/license.html>.
=cut
|
