path: root/INSTALL.md

How to Install Open vSwitch on Linux, FreeBSD and NetBSD
========================================================

This document describes how to build and install Open vSwitch on a
generic Linux, FreeBSD, or NetBSD host. For specifics around installation
on a specific platform, please see one of these files:

  - [INSTALL.Debian.md]
  - [INSTALL.Fedora.md]
  - [INSTALL.RHEL.md]
  - [INSTALL.XenServer.md]
  - [INSTALL.NetBSD.md]
  - [INSTALL.Windows.md]
  - [INSTALL.DPDK.md]

Build Requirements
------------------

To compile the userspace programs in the Open vSwitch distribution,
you will need the following software:

  - GNU make.

  - A C compiler, such as:

      * GCC 4.x.

      * Clang.  Clang 3.4 and later provide useful static semantic
        analysis and thread-safety checks.  For Ubuntu, there are
        nightly built packages available on clang's website.

      * MSVC 2013.  See [INSTALL.Windows] for additional Windows build
        instructions.

    While OVS may be compatible with other compilers, optimal
    support for atomic operations may be missing, making OVS very
    slow (see lib/ovs-atomic.h).

  - libssl, from OpenSSL, is optional but recommended if you plan to
    connect the Open vSwitch to an OpenFlow controller.  libssl is
    required to establish confidentiality and authenticity in the
    connections from an Open vSwitch to an OpenFlow controller.  If
    libssl is installed, then Open vSwitch will automatically build
    with support for it.

  - libcap-ng, written by Steve Grubb, is optional but recommended.  It
    is required to run OVS daemons as a non-root user with dropped root
    privileges.  If libcap-ng is installed, then Open vSwitch will
    automatically build with support for it.

  - Python 2.7. You must also have the Python six library.

On Linux, you may choose to compile the kernel module that comes with
the Open vSwitch distribution or to use the kernel module built into
the Linux kernel (version 3.3 or later).  See the [FAQ.md] question
"What features are not available in the Open vSwitch kernel datapath that
ships as part of the upstream Linux kernel?" for more information on
this trade-off.  You may also use the userspace-only implementation,
at some cost in features and performance (see [INSTALL.userspace.md]
for details).  To compile the kernel module on Linux, you must also
install the following:

  - A supported Linux kernel version.  Please refer to [README.md] for a
    list of supported versions.

    For optional support of ingress policing, you must enable kernel
    configuration options NET_CLS_BASIC, NET_SCH_INGRESS, and
    NET_ACT_POLICE, either built-in or as modules.  (NET_CLS_POLICE is
    obsolete and not needed.)

    On kernels before 3.11, the ip_gre module, for GRE tunnels over IP
    (NET_IPGRE), must not be loaded or compiled in.

    To configure HTB or HFSC quality of service with Open vSwitch,
    you must enable the respective configuration options.

    To use Open vSwitch support for TAP devices, you must enable
    CONFIG_TUN.

  - To build a kernel module, you need the same version of GCC that
    was used to build that kernel.

  - A kernel build directory corresponding to the Linux kernel image
    the module is to run on.  Under Debian and Ubuntu, for example,
    each linux-image package containing a kernel binary has a
    corresponding linux-headers package with the required build
    infrastructure.

If you are working from a Git tree or snapshot (instead of from a
distribution tarball), or if you modify the Open vSwitch build system
or the database schema, you will also need the following software:

  - Autoconf version 2.63 or later.

  - Automake version 1.10 or later.

  - libtool version 2.4 or later.  (Older versions might work too.)

To run the unit tests, you also need:

  - Perl.  Version 5.10.1 is known to work.  Earlier versions should
    also work.

The datapath tests for userspace and Linux datapaths also rely upon:

  - pyftpdlib. Version 1.2.0 is known to work. Earlier versions should
    also work.

  - GNU wget. Version 1.16 is known to work. Earlier versions should
    also work.

The ovs-vswitchd.conf.db(5) manpage will include an E-R diagram, in
formats other than plain text, only if you have the following:

  - "dot" from graphviz (http://www.graphviz.org/).

  - Perl.  Version 5.10.1 is known to work.  Earlier versions should
    also work.

If you are going to extensively modify Open vSwitch, please consider
installing the following to obtain better warnings:

  - "sparse" version 0.4.4 or later
    (http://www.kernel.org/pub/software/devel/sparse/dist/).

  - GNU make.

  - clang, version 3.4 or later

  - “flake8”, version 2.X, along with the “hacking” flake8 plugin (for Python
    code).  The automatic flake8 check that runs against Python code has some
    warnings enabled that come from the "hacking" flake8 plugin.  If it's not
    installed, the warnings just won't occur until it's run on a system with
    "hacking" installed.  Note that there are problems with flake8 3.0 and the
    “hacking” plugin.  To ensure you get flake8 2.X, you can use
    “pip install ‘flake8<3.0’”.

Also, you may find the ovs-dev script found in utilities/ovs-dev.py useful.

Installation Requirements
-------------------------

The machine on which Open vSwitch is to be installed must have the
following software:

  - libc compatible with the libc used for build.

  - libssl compatible with the libssl used for build, if OpenSSL was
    used for the build.

  - On Linux, the same kernel version configured as part of the build.

  - For optional support of ingress policing on Linux, the "tc" program
    from iproute2 (part of all major distributions and available at
    http://www.linux-foundation.org/en/Net:Iproute2).

  - Python 2.7. You must also have the Python six library.

On Linux you should ensure that /dev/urandom exists.  To support TAP
devices, you must also ensure that /dev/net/tun exists.

Building and Installing Open vSwitch for Linux, FreeBSD or NetBSD
=================================================================

Once you have installed all the prerequisites listed above in the
Base Prerequisites section, follow the procedures below to bootstrap,
to configure and to build the code.

Bootstrapping the Sources
-------------------------

This step is not needed if you have downloaded a released tarball.
If you pulled the sources directly from an Open vSwitch Git tree or
got a Git tree snapshot, then run boot.sh in the top source directory
to build the "configure" script.

      `% ./boot.sh`


Configuring the Sources
-----------------------

Configure the package by running the configure script.  You can
usually invoke configure without any arguments.  For example:

      `% ./configure`

By default all files are installed under /usr/local.  Open vSwitch also
expects to find its database in /usr/local/etc/openvswitch by default.
If you want to install all files into, e.g., /usr and /var instead of
/usr/local and /usr/local/var and expect to use /etc/openvswitch as the default
database directory, add options as shown here:

      `% ./configure --prefix=/usr --localstatedir=/var --sysconfdir=/etc`

Note that the Open vSwitch installed with packages like .rpm (e.g. via 'yum
install' or 'rpm -ivh') and .deb (e.g. via 'apt-get install' or 'dpkg -i') use
the above configure options.

By default, static libraries are built and linked against. If you
want to use shared libraries instead:

      `% ./configure --enable-shared`

To use a specific C compiler for compiling Open vSwitch user
programs, also specify it on the configure command line, like so:

      `% ./configure CC=gcc-4.2`

To use 'clang' compiler:

      `% ./configure CC=clang`

To supply special flags to the C compiler, specify them as CFLAGS on
the configure command line.  If you want the default CFLAGS, which
include "-g" to build debug symbols and "-O2" to enable optimizations,
you must include them yourself.  For example, to build with the
default CFLAGS plus "-mssse3", you might run configure as follows:

      `% ./configure CFLAGS="-g -O2 -mssse3"`

For efficient hash computation special flags can be passed to leverage
built-in intrinsics.  For example on X86_64 with SSE4.2 instruction set
support, CRC32 intrinsics can be used by passing '-msse4.2'.

      `% ./configure CFLAGS="-g -O2 -msse4.2"`

If you are on a different processor and don't know what flags to choose, it
is recommended to use '-march=native' settings.

      `% ./configure CFLAGS="-g -O2 -march=native"`

With this, GCC will detect the processor and automatically set appropriate
flags for it.  This should not be used if you are compiling OVS outside the
target machine.

Note that these CFLAGS are not applied when building the Linux
kernel module.  Custom CFLAGS for the kernel module are supplied
using the EXTRA_CFLAGS variable when running make.  So, for example:

      `% make EXTRA_CFLAGS="-Wno-error=date-time"`

To build the Linux kernel module, so that you can run the
kernel-based switch, pass the location of the kernel build
directory on --with-linux.  For example, to build for a running
instance of Linux:

      `% ./configure --with-linux=/lib/modules/`uname -r`/build`

If --with-linux requests building for an unsupported version of
Linux, then "configure" will fail with an error message.  Please
refer to the [FAQ.md] for advice in that case.

If you wish to build the kernel module for an architecture other
than the architecture of the machine used for the build, you may
specify the kernel architecture string using the KARCH variable
when invoking the configure script.  For example, to build for MIPS
with Linux:

      `% ./configure --with-linux=/path/to/linux KARCH=mips`

If you plan to do much Open vSwitch development, you might want to
add --enable-Werror, which adds the -Werror option to the compiler
command line, turning warnings into errors.  That makes it
impossible to miss warnings generated by the build.

To build with gcov code coverage support, add --enable-coverage,
e.g.:

      `% ./configure --enable-coverage`

The configure script accepts a number of other options and honors
additional environment variables.  For a full list, invoke
configure with the --help option.

You can also run configure from a separate build directory.  This
is helpful if you want to build Open vSwitch in more than one way
from a single source directory, e.g. to try out both GCC and Clang
builds, or to build kernel modules for more than one Linux version.
Here is an example:

      `% mkdir _gcc && (cd _gcc && ../configure CC=gcc)`
      `% mkdir _clang && (cd _clang && ../configure CC=clang)`

Under certains loads the ovsdb-server and other components perform
better when using the jemalloc memory allocator, instead of the glibc
memory allocator.

If you wish to link with jemalloc add it to LIBS:

      `% ./configure LIBS=-ljemalloc`

Building the Sources
--------------------

1. Run GNU make in the build directory, e.g.:

      `% make`

   or if GNU make is installed as "gmake":

      `% gmake`

   If you used a separate build directory, run make or gmake from that
   directory, e.g.:

      `% make -C _gcc`
      `% make -C _clang`

   For improved warnings if you installed "sparse" (see "Prerequisites"),
   add C=1 to the command line.

   Some versions of Clang and ccache are not completely compatible.
   If you see unusual warnings when you use both together, consider
   disabling ccache for use with Clang.

2. Consider running the testsuite.  Refer to "Running the Testsuite"
   below, for instructions.

3. Become root by running "su" or another program.

4. Run "make install" to install the executables and manpages into the
   running system, by default under /usr/local.

5. If you built kernel modules, you may install and load them, e.g.:

      `% make modules_install`
      `% /sbin/modprobe openvswitch`

   To verify that the modules have been loaded, run "/sbin/lsmod" and
   check that openvswitch is listed.

   If the `modprobe` operation fails, look at the last few kernel log
   messages (e.g. with `dmesg | tail`):

      - Otherwise, the most likely problem is that Open vSwitch was
        built for a kernel different from the one into which you are
        trying to load it.  Run `modinfo` on openvswitch.ko and on
        a module built for the running kernel, e.g.:

           ```
           % /sbin/modinfo openvswitch.ko
           % /sbin/modinfo /lib/modules/`uname -r`/kernel/net/bridge/bridge.ko
           ```

        Compare the "vermagic" lines output by the two commands.  If
        they differ, then Open vSwitch was built for the wrong kernel.

      - If you decide to report a bug or ask a question related to
        module loading, please include the output from the `dmesg` and
        `modinfo` commands mentioned above.

6. Initialize the configuration database using ovsdb-tool, e.g.:

      `% mkdir -p /usr/local/etc/openvswitch`
      `% ovsdb-tool create /usr/local/etc/openvswitch/conf.db vswitchd/vswitch.ovsschema`

Startup
=======

Before starting ovs-vswitchd itself, you need to start its
configuration database, ovsdb-server.  Each machine on which Open
vSwitch is installed should run its own copy of ovsdb-server.
Configure it to use the database you created during installation (as
explained above), to listen on a Unix domain socket, to connect to any
managers specified in the database itself, and to use the SSL
configuration in the database:

      ```
      % ovsdb-server --remote=punix:/usr/local/var/run/openvswitch/db.sock \
                     --remote=db:Open_vSwitch,Open_vSwitch,manager_options \
                     --private-key=db:Open_vSwitch,SSL,private_key \
                     --certificate=db:Open_vSwitch,SSL,certificate \
                     --bootstrap-ca-cert=db:Open_vSwitch,SSL,ca_cert \
                     --pidfile --detach
      ```

(If you built Open vSwitch without SSL support, then omit
--private-key, --certificate, and --bootstrap-ca-cert.)

Then initialize the database using ovs-vsctl.  This is only
necessary the first time after you create the database with
ovsdb-tool (but running it at any time is harmless):

      `% ovs-vsctl --no-wait init`

Then start the main Open vSwitch daemon, telling it to connect to the
same Unix domain socket:

      `% ovs-vswitchd --pidfile --detach`

Now you may use ovs-vsctl to set up bridges and other Open vSwitch
features.  For example, to create a bridge named br0 and add ports
eth0 and vif1.0 to it:

      `% ovs-vsctl add-br br0`
      `% ovs-vsctl add-port br0 eth0`
      `% ovs-vsctl add-port br0 vif1.0`

Please refer to ovs-vsctl(8) for more details.

Upgrading
=========

When you upgrade Open vSwitch from one version to another, you should
also upgrade the database schema:

1. Stop the Open vSwitch daemons, e.g.:

      ```
      % kill `cd /usr/local/var/run/openvswitch && cat ovsdb-server.pid ovs-vswitchd.pid`
      ```

2. Install the new Open vSwitch release by using the same configure options as
was used for installing the previous version. If you do not use the same
configure options, you can end up with two different versions of Open vSwitch
executables installed in different locations.

3. Upgrade the database, in one of the following two ways:

      - If there is no important data in your database, then you may
        delete the database file and recreate it with ovsdb-tool,
        following the instructions under "Building and Installing Open
        vSwitch for Linux, FreeBSD or NetBSD".

      - If you want to preserve the contents of your database, back it
        up first, then use "ovsdb-tool convert" to upgrade it, e.g.:

        `% ovsdb-tool convert /usr/local/etc/openvswitch/conf.db vswitchd/vswitch.ovsschema`

4. Start the Open vSwitch daemons as described under "Building and
   Installing Open vSwitch for Linux, FreeBSD or NetBSD" above.

Hot Upgrading
=============
Upgrading Open vSwitch from one version to the next version with minimum
disruption of traffic going through the system that is using that Open vSwitch
needs some considerations:

1. If the upgrade only involves upgrading the userspace utilities and daemons
of Open vSwitch, make sure that the new userspace version is compatible with
the previously loaded kernel module.

2. An upgrade of userspace daemons means that they have to be restarted.
Restarting the daemons means that the OpenFlow flows in the ovs-vswitchd daemon
will be lost.  One way to restore the flows is to let the controller
re-populate it.  Another way is to save the previous flows using a utility
like ovs-ofctl and then re-add them after the restart. Restoring the old flows
is accurate only if the new Open vSwitch interfaces retain the old 'ofport'
values.

3. When the new userspace daemons get restarted, they automatically flush
the old flows setup in the kernel. This can be expensive if there are hundreds
of new flows that are entering the kernel but userspace daemons are busy
setting up new userspace flows from either the controller or an utility like
ovs-ofctl. Open vSwitch database provides an option to solve this problem
through the other_config:flow-restore-wait column of the Open_vSwitch table.
Refer to the ovs-vswitchd.conf.db(5) manpage for details.

4. If the upgrade also involves upgrading the kernel module, the old kernel
module needs to be unloaded and the new kernel module should be loaded. This
means that the kernel network devices belonging to Open vSwitch is recreated
and the kernel flows are lost. The downtime of the traffic can be reduced
if the userspace daemons are restarted immediately and the userspace flows
are restored as soon as possible.

The ovs-ctl utility's "restart" function only restarts the userspace daemons,
makes sure that the 'ofport' values remain consistent across restarts, restores
userspace flows using the ovs-ofctl utility and also uses the
other_config:flow-restore-wait column to keep the traffic downtime to the
minimum. The ovs-ctl utility's "force-reload-kmod" function does all of the
above, but also replaces the old kernel module with the new one. Open vSwitch
startup scripts for Debian, XenServer and RHEL use ovs-ctl's functions and it
is recommended that these functions be used for other software platforms too.

Testsuites
==========

This section describe Open vSwitch's built-in support for various test
suites.  You must bootstrap, configure and build Open vSwitch (steps are
in "Building and Installing Open vSwitch for Linux, FreeBSD or NetBSD"
above) before you run the tests described here.  You do not need to
install Open vSwitch or to build or load the kernel module to run
these test suites.  You do not need supervisor privilege to run these
test suites.

Self-Tests
----------

Open vSwitch includes a suite of self-tests.  Before you submit patches
upstream, we advise that you run the tests and ensure that they pass.
If you add new features to Open vSwitch, then adding tests for those
features will ensure your features don't break as developers modify
other areas of Open vSwitch.

Refer to "Testsuites" above for prerequisites.

To run all the unit tests in Open vSwitch, one at a time:
      `make check`
This takes under 5 minutes on a modern desktop system.

To run all the unit tests in Open vSwitch, up to 8 in parallel:
      `make check TESTSUITEFLAGS=-j8`
This takes under a minute on a modern 4-core desktop system.

To see a list of all the available tests, run:
      `make check TESTSUITEFLAGS=--list`

To run only a subset of tests, e.g. test 123 and tests 477 through 484:
      `make check TESTSUITEFLAGS='123 477-484'`
(Tests do not have inter-dependencies, so you may run any subset.)

To run tests matching a keyword, e.g. "ovsdb":
      `make check TESTSUITEFLAGS='-k ovsdb'`

To see a complete list of test options:
      `make check TESTSUITEFLAGS=--help`

The results of a testing run are reported in tests/testsuite.log.
Please report test failures as bugs and include the testsuite.log in
your report.

If the build was configured with "--enable-coverage" and the "lcov"
utility is installed, you can run the testsuite and generate a code
coverage report by using "make check-lcov". All of the options for
TESTSUITEFLAGS are available, so you can e.g.:
      `make check-lcov TESTSUITEFLAGS=-j8 -k ovn`

If you have "valgrind" installed, then you can also run the testsuite
under valgrind by using "make check-valgrind" in place of "make
check".  All the same options are available via TESTSUITEFLAGS.  When
you do this, the "valgrind" results for test `<N>` are reported in files
named `tests/testsuite.dir/<N>/valgrind.*`.  You may find that the
valgrind results are easier to interpret if you put "-q" in
~/.valgrindrc, since that reduces the amount of output.

Sometimes a few tests may fail on some runs but not others.  This is
usually a bug in the testsuite, not a bug in Open vSwitch itself.  If
you find that a test fails intermittently, please report it, since the
developers may not have noticed.  You can make the testsuite
automatically rerun tests that fail, by adding RECHECK=yes to the
"make" command line, e.g.:
      `make check TESTSUITEFLAGS=-j8 RECHECK=yes`

OFTest
------

OFTest is an OpenFlow protocol testing suite.  Open vSwitch includes a
Makefile target to run OFTest with Open vSwitch in "dummy mode".  In
this mode of testing, no packets travel across physical or virtual
networks.  Instead, Unix domain sockets stand in as simulated
networks.  This simulation is imperfect, but it is much easier to set
up, does not require extra physical or virtual hardware, and does not
require supervisor privileges.

To run OFTest with Open vSwitch, first read and follow the
instructions under "Testsuites" above.  Second, obtain a copy of
OFTest and install its prerequisites.  You need a copy of OFTest that
includes commit 406614846c5 (make ovs-dummy platform work again).
This commit was merged into the OFTest repository on Feb 1, 2013, so
any copy of OFTest more recent than that should work.  Testing OVS in
dummy mode does not require root privilege, so you may ignore that
requirement.

Optionally, add the top-level OFTest directory (containing the "oft"
program) to your $PATH.  This slightly simplifies running OFTest later.

To run OFTest in dummy mode, run the following command from your Open
vSwitch build directory:
    `make check-oftest OFT=<oft-binary>`
where `<oft-binary>` is the absolute path to the "oft" program in
OFTest.

If you added "oft" to your $PATH, you may omit the OFT variable
assignment:
    `make check-oftest`
By default, "check-oftest" passes "oft" just enough options to enable
dummy mode.  You can use OFTFLAGS to pass additional options.  For
example, to run just the basic.Echo test instead of all tests (the
default) and enable verbose logging:
    `make check-oftest OFT=<oft-binary> OFTFLAGS='--verbose -T basic.Echo'`

If you use OFTest that does not include commit 4d1f3eb2c792 (oft:
change default port to 6653), merged into the OFTest repository in
October 2013, then you need to add an option to use the IETF-assigned
controller port:
    `make check-oftest OFT=<oft-binary> OFTFLAGS='--port=6653'`

Please interpret OFTest results cautiously.  Open vSwitch can fail a
given test in OFTest for many reasons, including bugs in Open vSwitch,
bugs in OFTest, bugs in the "dummy mode" integration, and differing
interpretations of the OpenFlow standard and other standards.

Open vSwitch has not been validated against OFTest.  Please do report
test failures that you believe to represent bugs in Open vSwitch.
Include the precise versions of Open vSwitch and OFTest in your bug
report, plus any other information needed to reproduce the problem.

Ryu
---

Ryu is an OpenFlow controller written in Python that includes an
extensive OpenFlow testsuite.  Open vSwitch includes a Makefile target
to run Ryu in "dummy mode".  See "OFTest" above for an explanation of
dummy mode.

To run Ryu tests with Open vSwitch, first read and follow the
instructions under "Testsuites" above.  Second, obtain a copy of Ryu,
install its prerequisites, and build it.  You do not need to install
Ryu (some of the tests do not get installed, so it does not help).

To run Ryu tests, run the following command from your Open vSwitch
build directory:
    `make check-ryu RYUDIR=<ryu-source-dir>`
where `<ryu-source-dir>` is the absolute path to the root of the Ryu
source distribution.  The default `<ryu-source-dir>` is `$srcdir/../ryu`
where $srcdir is your Open vSwitch source directory, so if this
default is correct then you make simply run `make check-ryu`.

Open vSwitch has not been validated against Ryu.  Please do report
test failures that you believe to represent bugs in Open vSwitch.
Include the precise versions of Open vSwitch and Ryu in your bug
report, plus any other information needed to reproduce the problem.

Datapath testing
----------------

Open vSwitch also includes a suite of tests specifically for datapath
functionality, which can be run against the userspace or kernel datapaths.
If you are developing datapath features, it is recommended that you use
these tests and build upon them to verify your implementation.

The datapath tests make some assumptions about the environment. They
must be run under root privileges on a Linux system with support for
network namespaces. For ease of use, the OVS source tree includes a
vagrant box to invoke these tests. Running the tests inside Vagrant
provides kernel isolation, protecting your development host from kernel
panics or configuration conflicts in the testsuite. If you wish to run
the tests without using the vagrant box, there are further instructions
below.

### Vagrant

*Requires Vagrant (version 1.7.0 or later) and a compatible hypervisor*

You must bootstrap and configure the sources (steps are in "Building
and Installing Open vSwitch for Linux, FreeBSD or NetBSD" above) before
you run the steps described here.

A Vagrantfile is provided allowing to compile and provision the source
tree as found locally in a virtual machine using the following command:

	vagrant up

This will bring up a Fedora 23 VM by default. If you wish to use a
different box or a vagrant backend not supported by the default box,
the `Vagrantfile` can be modified to use a different box as base.

The VM can be reprovisioned at any time:

	vagrant provision

OVS out-of-tree compilation environment can be set up with:

	./boot.sh
	vagrant provision --provision-with configure_ovs,build_ovs

This will set up an out-of-tree build environment inside the VM in
/root/build. The source code can be found in /vagrant.

To recompile and reinstall OVS in the VM using RPM:

	./boot.sh
	vagrant provision --provision-with configure_ovs,install_rpm

Two provisioners are included to run system tests with the OVS kernel
module or with a userspace datapath.  This tests are different from
the self-tests mentioned above.  To run them:

	./boot.sh
	vagrant provision --provision-with configure_ovs,test_ovs_kmod,test_ovs_system_userspace

The results of the testsuite reside in the VM root user's home directory:

        vagrant ssh
        sudo -s
        cd /root/build
        ls tests/system*

### Native

The datapath testsuite as invoked by Vagrant above may also be run
manually on a Linux system with root privileges. These tests may take
several minutes to complete, and cannot be run in parallel.

#### Userspace datapath

To invoke the datapath testsuite with the userspace datapath:

        make check-system-userspace

The results of the testsuite are in tests/system-userspace-traffic.dir/.

#### Kernel datapath

Make targets are also provided for testing the Linux kernel module.
Note that these tests operate by inserting modules into the running
Linux kernel, so if the tests are able to trigger a bug in the OVS
kernel module or in the upstream kernel then the kernel may panic.

To run the testsuite against the kernel module which is currently
installed on your system:

        make check-kernel

To install the kernel module from the current build directory and
run the testsuite against that kernel module:

        make check-kmod

The results of the testsuite are in tests/system-kmod-traffic.dir/.

Continuous Integration with Travis-CI
-------------------------------------

A .travis.yml file is provided to automatically build Open vSwitch with
various build configurations and run the testsuite using travis-ci.
Builds will be performed with gcc, sparse and clang with the -Werror
compiler flag included, therefore the build will fail if a new warning
has been introduced.

The CI build is triggered via git push (regardless of the specific
branch) or pull request against any Open vSwitch GitHub repository that
is linked to travis-ci.

Instructions to setup travis-ci for your GitHub repository:

1. Go to http://travis-ci.org/ and sign in using your GitHub ID.
2. Go to the "Repositories" tab and enable the ovs repository. You
   may disable builds for pushes or pull requests.
3. In order to avoid forks sending build failures to the upstream
   mailing list, the notification email recipient is encrypted. If you
   want to receive email notification for build failures, replace the
   the encrypted string:
   3.1) Install the travis-ci CLI (Requires ruby >=2.0):
           gem install travis
   3.2) In your Open vSwitch repository:
           travis encrypt mylist@mydomain.org
   3.3) Add/replace the notifications section in .travis.yml and fill
        in the secure string as returned by travis encrypt:

         notifications:
           email:
             recipients:
               - secure: "....."

   (You may remove/omit the notifications section to fall back to
    default notification behaviour which is to send an email directly
    to the author and committer of the failing commit. Note that the
    email is only sent if the author/committer have commit rights for
    the particular GitHub repository).

4. Pushing a commit to the repository which breaks the build or the
   testsuite will now trigger a email sent to mylist@mydomain.org

Static Code Analysis
--------------------

Static Analysis is a method of debugging Software by examining code rather
than actually executing it. This can be done through 'scan-build' commandline
utility which internally uses clang (or) gcc to compile the code and also
invokes a static analyzer to do the code analysis. At the end of the build, the
reports are aggregated in to a common folder and can later be analyzed using
'scan-view'.

Open vSwitch includes a Makefile target to trigger static code Analysis and
the instructions are below.

1. ./boot.sh
2. ./configure CC=clang (when using clang compiler)
   ./configure CC=gcc CFLAGS="-std=gnu99" (when using GCC)
3. make clang-analyze

You should invoke scan-view to view analysis results. The last line of output
from 'make clang-analyze' shall list the command (containing results directory)
that you should invoke to view the results on a browser.

Bug Reporting
=============

Please report problems to bugs@openvswitch.org.

[README.md]:README.md
[INSTALL.Debian.md]:INSTALL.Debian.md
[INSTALL.Fedora.md]:INSTALL.Fedora.md
[INSTALL.RHEL.md]:INSTALL.RHEL.md
[INSTALL.XenServer.md]:INSTALL.XenServer.md
[INSTALL.NetBSD.md]:INSTALL.NetBSD.md
[INSTALL.Windows.md]:INSTALL.Windows.md
[INSTALL.DPDK.md]:INSTALL.DPDK.md
[INSTALL.userspace.md]:INSTALL.userspace.md
[FAQ.md]:FAQ.md