1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
|
From 4c0b77276307d2cba8ae2595cbae4cc916c84c36 Mon Sep 17 00:00:00 2001
From: Claudiu Beznea <claudiu.beznea@microchip.com>
Date: Wed, 15 Sep 2021 10:48:36 +0300
Subject: [PATCH 233/247] ARM: dts: at91: sama7g5ek: to not touch slew-rate for
SDMMC pins
With commit c709135e576b ("pinctrl: at91-pio4: add support for slew-rate")
and commit cbde6c823bfa ("pinctrl: at91-pio4: Fix slew rate disablement")
the slew-rate is enabled by default for each configured pin. The datasheet
specifies at chapter "Output Driver AC Characteristics" that HSIO
drivers (use in SDMMCx and QSPI0 peripherals), don't have a slewrate
setting but are rather calibrated against an external 1% resistor mounted
on the SDMMCx_CAL or QSPI0_CAL pins. Depending on the target signal
frequency and the external load, it is possible to adjust their target
output impedance. Thus set slew-rate = <0> for SDMMC (QSPI is not enabled
at the moment in device tree).
Fixes: 7540629e2fc7 ("ARM: dts: at91: add sama7g5 SoC DT and sama7g5-ek")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Link: https://lore.kernel.org/r/20210915074836.6574-3-claudiu.beznea@microchip.com
---
arch/arm/boot/dts/at91-sama7g5ek.dts | 6 ++++++
1 file changed, 6 insertions(+)
--- a/arch/arm/boot/dts/at91-sama7g5ek.dts
+++ b/arch/arm/boot/dts/at91-sama7g5ek.dts
@@ -558,6 +558,7 @@
<PIN_PA8__SDMMC0_DAT5>,
<PIN_PA9__SDMMC0_DAT6>,
<PIN_PA10__SDMMC0_DAT7>;
+ slew-rate = <0>;
bias-pull-up;
};
@@ -565,6 +566,7 @@
pinmux = <PIN_PA0__SDMMC0_CK>,
<PIN_PA2__SDMMC0_RSTN>,
<PIN_PA11__SDMMC0_DS>;
+ slew-rate = <0>;
bias-pull-up;
};
};
@@ -576,6 +578,7 @@
<PIN_PC0__SDMMC1_DAT1>,
<PIN_PC1__SDMMC1_DAT2>,
<PIN_PC2__SDMMC1_DAT3>;
+ slew-rate = <0>;
bias-pull-up;
};
@@ -584,6 +587,7 @@
<PIN_PB28__SDMMC1_RSTN>,
<PIN_PC5__SDMMC1_1V8SEL>,
<PIN_PC4__SDMMC1_CD>;
+ slew-rate = <0>;
bias-pull-up;
};
};
@@ -595,11 +599,13 @@
<PIN_PD6__SDMMC2_DAT1>,
<PIN_PD7__SDMMC2_DAT2>,
<PIN_PD8__SDMMC2_DAT3>;
+ slew-rate = <0>;
bias-pull-up;
};
ck {
pinmux = <PIN_PD4__SDMMC2_CK>;
+ slew-rate = <0>;
bias-pull-up;
};
};
|
