1 files changed, 0 insertions, 254 deletions
diff --git a/gpxe/src/core/serial.c b/gpxe/src/core/serial.c
deleted file mode 100644
index d35e89e9..00000000
--- a/gpxe/src/core/serial.c
+++ /dev/null
@@ -1,254 +0,0 @@
-/*
- * The serial port interface routines implement a simple polled i/o
- * interface to a standard serial port.  Due to the space restrictions
- * for the boot blocks, no BIOS support is used (since BIOS requires
- * expensive real/protected mode switches), instead the rudimentary
- * BIOS support is duplicated here.
- *
- * The base address and speed for the i/o port are passed from the
- * Makefile in the COMCONSOLE and CONSPEED preprocessor macros.  The
- * line control parameters are currently hard-coded to 8 bits, no
- * parity, 1 stop bit (8N1).  This can be changed in init_serial().
- */
-
-FILE_LICENCE ( GPL2_OR_LATER );
-
-#include "stddef.h"
-#include <gpxe/init.h>
-#include <gpxe/io.h>
-#include <unistd.h>
-#include <gpxe/serial.h>
-#include "config/serial.h"
-
-/* Set default values if none specified */
-
-#ifndef COMCONSOLE
-#define COMCONSOLE	0x3f8
-#endif
-
-#ifndef COMSPEED
-#define COMSPEED	9600
-#endif
-
-#ifndef COMDATA
-#define COMDATA		8
-#endif
-
-#ifndef COMPARITY
-#define COMPARITY	0
-#endif
-
-#ifndef COMSTOP
-#define COMSTOP		1
-#endif
-
-#undef UART_BASE
-#define UART_BASE ( COMCONSOLE )
-
-#undef UART_BAUD
-#define UART_BAUD ( COMSPEED )
-
-#if ((115200%UART_BAUD) != 0)
-#error Bad ttys0 baud rate
-#endif
-
-#define COMBRD (115200/UART_BAUD)
-
-/* Line Control Settings */
-#define UART_LCS ( ( ( (COMDATA) - 5 )	<< 0 ) | \
-		   ( ( (COMPARITY) )	<< 3 ) | \
-		   ( ( (COMSTOP) - 1 )	<< 2 ) )
-
-/* Data */
-#define UART_RBR 0x00
-#define UART_TBR 0x00
-
-/* Control */
-#define UART_IER 0x01
-#define UART_IIR 0x02
-#define UART_FCR 0x02
-#define UART_LCR 0x03
-#define UART_MCR 0x04
-#define UART_DLL 0x00
-#define UART_DLM 0x01
-
-/* Status */
-#define UART_LSR 0x05
-#define  UART_LSR_TEMPT 0x40	/* Transmitter empty */
-#define  UART_LSR_THRE  0x20	/* Transmit-hold-register empty */
-#define  UART_LSR_BI	0x10	/* Break interrupt indicator */
-#define  UART_LSR_FE	0x08	/* Frame error indicator */
-#define  UART_LSR_PE	0x04	/* Parity error indicator */
-#define  UART_LSR_OE	0x02	/* Overrun error indicator */
-#define  UART_LSR_DR	0x01	/* Receiver data ready */
-
-#define UART_MSR 0x06
-#define UART_SCR 0x07
-
-#if defined(UART_MEM)
-#define uart_readb(addr) readb((addr))
-#define uart_writeb(val,addr) writeb((val),(addr))
-#else
-#define uart_readb(addr) inb((addr))
-#define uart_writeb(val,addr) outb((val),(addr))
-#endif
-
-/*
- * void serial_putc(int ch);
- *	Write character `ch' to port UART_BASE.
- */
-void serial_putc ( int ch ) {
-	int i;
-	int status;
-	i = 1000; /* timeout */
-	while(--i > 0) {
-		status = uart_readb(UART_BASE + UART_LSR);
-		if (status & UART_LSR_THRE) { 
-			/* TX buffer emtpy */
-			uart_writeb(ch, UART_BASE + UART_TBR);
-			break;
-		}
-		mdelay(2);
-	}
-}
-
-/*
- * int serial_getc(void);
- *	Read a character from port UART_BASE.
- */
-int serial_getc ( void ) {
-	int status;
-	int ch;
-	do {
-		status = uart_readb(UART_BASE + UART_LSR);
-	} while((status & 1) == 0);
-	ch = uart_readb(UART_BASE + UART_RBR);	/* fetch (first) character */
-	ch &= 0x7f;				/* remove any parity bits we get */
-	if (ch == 0x7f) {			/* Make DEL... look like BS */
-		ch = 0x08;
-	}
-	return ch;
-}
-
-/*
- * int serial_ischar(void);
- *       If there is a character in the input buffer of port UART_BASE,
- *       return nonzero; otherwise return 0.
- */
-int serial_ischar ( void ) {
-	int status;
-	status = uart_readb(UART_BASE + UART_LSR);	/* line status reg; */
-	return status & 1;		/* rx char available */
-}
-
-/*
- * int serial_init(void);
- *	Initialize port UART_BASE to speed COMSPEED, line settings 8N1.
- */
-static void serial_init ( void ) {
-	int status;
-	int divisor, lcs;
-
-	DBG ( "Serial port %#x initialising\n", UART_BASE );
-
-	divisor = COMBRD;
-	lcs = UART_LCS;
-
-
-#ifdef COMPRESERVE
-	lcs = uart_readb(UART_BASE + UART_LCR) & 0x7f;
-	uart_writeb(0x80 | lcs, UART_BASE + UART_LCR);
-	divisor = (uart_readb(UART_BASE + UART_DLM) << 8) | uart_readb(UART_BASE + UART_DLL);
-	uart_writeb(lcs, UART_BASE + UART_LCR);
-#endif
-
-	/* Set Baud Rate Divisor to COMSPEED, and test to see if the
-	 * serial port appears to be present.
-	 */
-	uart_writeb(0x80 | lcs, UART_BASE + UART_LCR);
-	uart_writeb(0xaa, UART_BASE + UART_DLL);
-	if (uart_readb(UART_BASE + UART_DLL) != 0xaa) {
-		DBG ( "Serial port %#x UART_DLL failed\n", UART_BASE );
-		goto out;
-	}
-	uart_writeb(0x55, UART_BASE + UART_DLL);
-	if (uart_readb(UART_BASE + UART_DLL) != 0x55) {
-		DBG ( "Serial port %#x UART_DLL failed\n", UART_BASE );
-		goto out;
-	}
-	uart_writeb(divisor & 0xff, UART_BASE + UART_DLL);
-	if (uart_readb(UART_BASE + UART_DLL) != (divisor & 0xff)) {
-		DBG ( "Serial port %#x UART_DLL failed\n", UART_BASE );
-		goto out;
-	}
-	uart_writeb(0xaa, UART_BASE + UART_DLM);
-	if (uart_readb(UART_BASE + UART_DLM) != 0xaa) {
-		DBG ( "Serial port %#x UART_DLM failed\n", UART_BASE );
-		goto out;
-	}
-	uart_writeb(0x55, UART_BASE + UART_DLM);
-	if (uart_readb(UART_BASE + UART_DLM) != 0x55) {
-		DBG ( "Serial port %#x UART_DLM failed\n", UART_BASE );
-		goto out;
-	}
-	uart_writeb((divisor >> 8) & 0xff, UART_BASE + UART_DLM);
-	if (uart_readb(UART_BASE + UART_DLM) != ((divisor >> 8) & 0xff)) {
-		DBG ( "Serial port %#x UART_DLM failed\n", UART_BASE );
-		goto out;
-	}
-	uart_writeb(lcs, UART_BASE + UART_LCR);
-	
-	/* disable interrupts */
-	uart_writeb(0x0, UART_BASE + UART_IER);
-
-	/* disable fifo's */
-	uart_writeb(0x00, UART_BASE + UART_FCR);
-
-	/* Set clear to send, so flow control works... */
-	uart_writeb((1<<1), UART_BASE + UART_MCR);
-
-
-	/* Flush the input buffer. */
-	do {
-		/* rx buffer reg
-		 * throw away (unconditionally the first time)
-		 */
-	        (void) uart_readb(UART_BASE + UART_RBR);
-		/* line status reg */
-		status = uart_readb(UART_BASE + UART_LSR);
-	} while(status & UART_LSR_DR);
- out:
-	return;
-}
-
-/*
- * void serial_fini(void);
- *	Cleanup our use of the serial port, in particular flush the
- *	output buffer so we don't accidentially lose characters.
- */
-static void serial_fini ( int flags __unused ) {
-	int i, status;
-	/* Flush the output buffer to avoid dropping characters,
-	 * if we are reinitializing the serial port.
-	 */
-	i = 10000; /* timeout */
-	do {
-		status = uart_readb(UART_BASE + UART_LSR);
-	} while((--i > 0) && !(status & UART_LSR_TEMPT));
-	/* Don't mark it as disabled; it's still usable */
-}
-
-/**
- * Serial driver initialisation function
- *
- * Initialise serial port early on so that it is available to capture
- * early debug messages.
- */
-struct init_fn serial_init_fn __init_fn ( INIT_SERIAL ) = {
-	.initialise = serial_init,
-};
-
-/** Serial driver startup function */
-struct startup_fn serial_startup_fn __startup_fn ( STARTUP_EARLY ) = {
-	.shutdown = serial_fini,
-};