powerpc: ppc4xx: remove JSE board support

This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Stephen Williams <steve@icarus.com>

14 files changed, 1 insertions, 1329 deletions

diff --git a/arch/powerpc/cpu/ppc4xx/Kconfig b/arch/powerpc/cpu/ppc4xx/Kconfig
index 5db5e34627..e1512001f1 100644
--- a/arch/powerpc/cpu/ppc4xx/Kconfig
+++ b/arch/powerpc/cpu/ppc4xx/Kconfig
@@ -13,9 +13,6 @@ config TARGET_CSB272
 config TARGET_CSB472
 	bool "Support csb472"
 
-config TARGET_JSE
-	bool "Support JSE"
-
 config TARGET_KORAT
 	bool "Support korat"
 
@@ -204,7 +201,6 @@ source "board/gdsys/405ex/Kconfig"
 source "board/gdsys/dlvision/Kconfig"
 source "board/gdsys/gdppc440etx/Kconfig"
 source "board/gdsys/intip/Kconfig"
-source "board/jse/Kconfig"
 source "board/korat/Kconfig"
 source "board/lwmon5/Kconfig"
 source "board/mosaixtech/icon/Kconfig"
diff --git a/board/jse/Kconfig b/board/jse/Kconfig
deleted file mode 100644
index 48905fa76f..0000000000
--- a/board/jse/Kconfig
+++ /dev/null
@@ -1,9 +0,0 @@
-if TARGET_JSE
-
-config SYS_BOARD
-	default "jse"
-
-config SYS_CONFIG_NAME
-	default "JSE"
-
-endif
diff --git a/board/jse/MAINTAINERS b/board/jse/MAINTAINERS
deleted file mode 100644
index 818a5a0be4..0000000000
--- a/board/jse/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-JSE BOARD
-M:	Stephen Williams <steve@icarus.com>
-S:	Maintained
-F:	board/jse/
-F:	include/configs/JSE.h
-F:	configs/JSE_defconfig
diff --git a/board/jse/Makefile b/board/jse/Makefile
deleted file mode 100644
index feac3a8834..0000000000
--- a/board/jse/Makefile
+++ /dev/null
@@ -1,12 +0,0 @@
-#
-# (C) Copyright 2006
-# Wolfgang Denk, DENX Software Engineering, wd@denx.de.
-#
-# Copyright 2004 Picture Elements, Inc.
-# Stephen Williams <steve@icarus.com>
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	= jse.o sdram.o flash.o host_bridge.o
-obj-y	+= init.o
diff --git a/board/jse/README.txt b/board/jse/README.txt
deleted file mode 100644
index 84497db70f..0000000000
--- a/board/jse/README.txt
+++ /dev/null
@@ -1,48 +0,0 @@
-JSE Configuration Details
-
-Memory Bank 0 -- Flash chip
----------------------------
-
-0xfff00000 - 0xffffffff
-
-The flash chip is really only 512Kbytes, but the high address bit of
-the 1Meg region is ignored, so the flash is replicated through the
-region. Thus, this is consistent with a flash base address 0xfff80000.
-
-The placement at the end is to be consistent with reset behavior,
-where the processor itself initially uses this bus to load the branch
-vector and start running.
-
-On-Chip Memory
---------------
-
-0xf4000000 - 0xf4000fff
-
-The 405GPr includes a 4K on-chip memory that can be placed however
-software chooses. I choose to place the memory at this address, to
-keep it out of the cachable areas.
-
-
-Memory Bank 1 -- SystemACE Controller
--------------------------------------
-
-0xf0000000 - 0xf00fffff
-
-The SystemACE chip is along on peripheral bank CS#1. We don't need
-much space, but 1Meg is the smallest we can configure the chip to
-allocate. We need it far away from the flash region, because this
-region is set to be non-cached.
-
-
-Internal Peripherals
---------------------
-
-0xef600300 - 0xef6008ff
-
-These are scattered various peripherals internal to the PPC405GPr
-chip.
-
-SDRAM
------
-
-0x00000000 - 0x07ffffff  (128 MBytes)
diff --git a/board/jse/flash.c b/board/jse/flash.c
deleted file mode 100644
index a550f7d03e..0000000000
--- a/board/jse/flash.c
+++ /dev/null
@@ -1,491 +0,0 @@
-/*
- * (C) Copyright 2000-2004
- * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * Modified 4/5/2001
- * Wait for completion of each sector erase command issued
- * 4/5/2001
- * Chris Hallinan - DS4.COM, Inc. - clh@net1plus.com
- */
-
-#include <common.h>
-#include <asm/ppc4xx.h>
-#include <asm/processor.h>
-
-#if CONFIG_SYS_MAX_FLASH_BANKS != 1
-#error "CONFIG_SYS_MAX_FLASH_BANKS must be 1"
-#endif
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];	/* info for FLASH chips	*/
-
-/*-----------------------------------------------------------------------
- * Functions
- */
-static ulong flash_get_size (vu_long * addr, flash_info_t * info);
-static int write_word (flash_info_t * info, ulong dest, ulong data);
-static void flash_get_offsets (ulong base, flash_info_t * info);
-
-#define ADDR0		0x5555
-#define ADDR1		0x2aaa
-#define FLASH_WORD_SIZE unsigned char
-
-/*-----------------------------------------------------------------------
- */
-
-unsigned long flash_init (void)
-{
-	unsigned long size_b0;
-
-	/* Init: no FLASHes known */
-	flash_info[0].flash_id = FLASH_UNKNOWN;
-
-	/* Static FLASH Bank configuration here - FIXME XXX */
-
-	size_b0 = flash_get_size ((vu_long *) FLASH_BASE0_PRELIM, &flash_info[0]);
-
-	if (flash_info[0].flash_id == FLASH_UNKNOWN) {
-		printf ("## Unknown FLASH on Bank 0 - Size = 0x%08lx = %ld MB\n",
-			size_b0, size_b0 << 20);
-	}
-
-	/* Only one bank */
-	/* Setup offsets */
-	flash_get_offsets (FLASH_BASE0_PRELIM, &flash_info[0]);
-
-	/* Monitor protection ON by default */
-	(void) flash_protect (FLAG_PROTECT_SET,
-			      FLASH_BASE0_PRELIM,
-			      FLASH_BASE0_PRELIM + monitor_flash_len - 1,
-			      &flash_info[0]);
-	flash_info[0].size = size_b0;
-
-	return size_b0;
-}
-
-
-/*-----------------------------------------------------------------------
- */
-/*
- * This implementation assumes that the flash chips are uniform sector
- * devices. This is true for all likely JSE devices.
- */
-static void flash_get_offsets (ulong base, flash_info_t * info)
-{
-	unsigned idx;
-	unsigned long sector_size = info->size / info->sector_count;
-
-	for (idx = 0; idx < info->sector_count; idx += 1) {
-		info->start[idx] = base + (idx * sector_size);
-	}
-}
-
-/*-----------------------------------------------------------------------
- */
-void flash_print_info (flash_info_t * info)
-{
-	int i;
-	int k;
-	int size;
-	int erased;
-	volatile unsigned long *flash;
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("missing or unknown FLASH type\n");
-		return;
-	}
-
-	switch (info->flash_id & FLASH_VENDMASK) {
-	case FLASH_MAN_AMD:
-		printf ("AMD ");
-		break;
-	case FLASH_MAN_FUJ:
-		printf ("FUJITSU ");
-		break;
-	case FLASH_MAN_SST:
-		printf ("SST ");
-		break;
-	case FLASH_MAN_STM:
-		printf ("ST Micro ");
-		break;
-	default:
-		printf ("Unknown Vendor ");
-		break;
-	}
-
-	  /* (Reduced table of only parts expected in JSE boards.) */
-	switch (info->flash_id) {
-	case FLASH_MAN_AMD | FLASH_AM040:
-		printf ("AM29F040 (512 Kbit, uniform sector size)\n");
-		break;
-	case FLASH_MAN_STM | FLASH_AM040:
-		printf ("MM29W040W (512 Kbit, uniform sector size)\n");
-		break;
-	default:
-		printf ("Unknown Chip Type\n");
-		break;
-	}
-
-	printf ("  Size: %ld KB in %d Sectors\n",
-		info->size >> 10, info->sector_count);
-
-	printf ("  Sector Start Addresses:");
-	for (i = 0; i < info->sector_count; ++i) {
-		/*
-		 * Check if whole sector is erased
-		 */
-		if (i != (info->sector_count - 1))
-			size = info->start[i + 1] - info->start[i];
-		else
-			size = info->start[0] + info->size - info->start[i];
-		erased = 1;
-		flash = (volatile unsigned long *) info->start[i];
-		size = size >> 2;	/* divide by 4 for longword access */
-		for (k = 0; k < size; k++) {
-			if (*flash++ != 0xffffffff) {
-				erased = 0;
-				break;
-			}
-		}
-
-		if ((i % 5) == 0)
-			printf ("\n   ");
-		printf (" %08lX%s%s",
-			info->start[i],
-			erased ? " E" : "  ", info->protect[i] ? "RO " : "   "
-		);
-	}
-	printf ("\n");
-	return;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-
-/*-----------------------------------------------------------------------
- */
-
-/*
- * The following code cannot be run from FLASH!
- */
-static ulong flash_get_size (vu_long * addr, flash_info_t * info)
-{
-	short i;
-	FLASH_WORD_SIZE value;
-	ulong base = (ulong) addr;
-	volatile FLASH_WORD_SIZE *addr2 = (FLASH_WORD_SIZE *) addr;
-
-	/* Write auto select command: read Manufacturer ID */
-	addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA;
-	addr2[ADDR1] = (FLASH_WORD_SIZE) 0x00550055;
-	addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00900090;
-
-	value = addr2[0];
-
-	switch (value) {
-	case (FLASH_WORD_SIZE) AMD_MANUFACT:
-		info->flash_id = FLASH_MAN_AMD;
-		break;
-	case (FLASH_WORD_SIZE) FUJ_MANUFACT:
-		info->flash_id = FLASH_MAN_FUJ;
-		break;
-	case (FLASH_WORD_SIZE) SST_MANUFACT:
-		info->flash_id = FLASH_MAN_SST;
-		break;
-	case (FLASH_WORD_SIZE)STM_MANUFACT:
-		info->flash_id = FLASH_MAN_STM;
-		break;
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		info->sector_count = 0;
-		info->size = 0;
-		printf("Unknown flash manufacturer code: 0x%x\n", value);
-		return (0);	/* no or unknown flash  */
-	}
-
-	value = addr2[1];	/* device ID		*/
-
-	switch (value) {
-	case (FLASH_WORD_SIZE) AMD_ID_F040B:
-		info->flash_id += FLASH_AM040;
-		info->sector_count = 8;
-		info->size = 0x0080000;	/* => 512 ko */
-		break;
-	case (FLASH_WORD_SIZE) AMD_ID_LV040B:
-		info->flash_id += FLASH_AM040;
-		info->sector_count = 8;
-		info->size = 0x0080000;	/* => 512 ko */
-		break;
-	case (FLASH_WORD_SIZE)STM_ID_M29W040B: /* most likele JSE chip */
-		info->flash_id += FLASH_AM040;
-		info->sector_count = 8;
-		info->size = 0x0080000; /* => 512 ko */
-		break;
-	default:
-		info->flash_id = FLASH_UNKNOWN;
-		return (0);	/* => no or unknown flash */
-
-	}
-
-	  /* Calculate the sector offsets (Use JSE Optimized code). */
-	flash_get_offsets(base, info);
-
-	/* check for protected sectors */
-	for (i = 0; i < info->sector_count; i++) {
-		/* read sector protection at sector address, (A7 .. A0) = 0x02 */
-		/* D0 = 1 if protected */
-		addr2 = (volatile FLASH_WORD_SIZE *) (info->start[i]);
-		if ((info->flash_id & FLASH_VENDMASK) == FLASH_MAN_SST)
-			info->protect[i] = 0;
-		else
-			info->protect[i] = addr2[2] & 1;
-	}
-
-	/*
-	 * Prevent writes to uninitialized FLASH.
-	 */
-	if (info->flash_id != FLASH_UNKNOWN) {
-		addr2 = (FLASH_WORD_SIZE *) info->start[0];
-		*addr2 = (FLASH_WORD_SIZE) 0x00F000F0;	/* reset bank */
-	}
-
-	return (info->size);
-}
-
-int wait_for_DQ7 (flash_info_t * info, int sect)
-{
-	ulong start, now, last;
-	volatile FLASH_WORD_SIZE *addr =
-		(FLASH_WORD_SIZE *) (info->start[sect]);
-
-	start = get_timer (0);
-	last = start;
-	while ((addr[0] & (FLASH_WORD_SIZE) 0x00800080) !=
-	       (FLASH_WORD_SIZE) 0x00800080) {
-		if ((now = get_timer (start)) > CONFIG_SYS_FLASH_ERASE_TOUT) {
-			printf ("Timeout\n");
-			return -1;
-		}
-		/* show that we're waiting */
-		if ((now - last) > 1000) {	/* every second */
-			putc ('.');
-			last = now;
-		}
-	}
-	return 0;
-}
-
-/*-----------------------------------------------------------------------
- */
-
-int flash_erase (flash_info_t * info, int s_first, int s_last)
-{
-	volatile FLASH_WORD_SIZE *addr = (FLASH_WORD_SIZE *) (info->start[0]);
-	volatile FLASH_WORD_SIZE *addr2;
-	int flag, prot, sect;
-	int i;
-
-	if ((s_first < 0) || (s_first > s_last)) {
-		if (info->flash_id == FLASH_UNKNOWN) {
-			printf ("- missing\n");
-		} else {
-			printf ("- no sectors to erase\n");
-		}
-		return 1;
-	}
-
-	if (info->flash_id == FLASH_UNKNOWN) {
-		printf ("Can't erase unknown flash type - aborted\n");
-		return 1;
-	}
-
-	prot = 0;
-	for (sect = s_first; sect <= s_last; ++sect) {
-		if (info->protect[sect]) {
-			prot++;
-		}
-	}
-
-	if (prot) {
-		printf ("- Warning: %d protected sectors will not be erased!\n", prot);
-	} else {
-		printf ("\n");
-	}
-
-	/* Disable interrupts which might cause a timeout here */
-	flag = disable_interrupts ();
-
-	/* Start erase on unprotected sectors */
-	for (sect = s_first; sect <= s_last; sect++) {
-		if (info->protect[sect] == 0) {	/* not protected */
-			addr2 = (FLASH_WORD_SIZE *) (info->start[sect]);
-			printf ("Erasing sector %p\n", addr2);	/* CLH */
-
-			if ((info->flash_id & FLASH_VENDMASK) ==
-			    FLASH_MAN_SST) {
-				addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA;
-				addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055;
-				addr[ADDR0] = (FLASH_WORD_SIZE) 0x00800080;
-				addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA;
-				addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055;
-				addr2[0] = (FLASH_WORD_SIZE) 0x00500050;	/* block erase */
-				for (i = 0; i < 50; i++)
-					udelay (1000);	/* wait 1 ms */
-			} else {
-				addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA;
-				addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055;
-				addr[ADDR0] = (FLASH_WORD_SIZE) 0x00800080;
-				addr[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA;
-				addr[ADDR1] = (FLASH_WORD_SIZE) 0x00550055;
-				addr2[0] = (FLASH_WORD_SIZE) 0x00300030;	/* sector erase */
-			}
-			/*
-			 * Wait for each sector to complete, it's more
-			 * reliable.  According to AMD Spec, you must
-			 * issue all erase commands within a specified
-			 * timeout.  This has been seen to fail, especially
-			 * if printf()s are included (for debug)!!
-			 */
-			wait_for_DQ7 (info, sect);
-		}
-	}
-
-	/* re-enable interrupts if necessary */
-	if (flag)
-		enable_interrupts ();
-
-	/* wait at least 80us - let's wait 1 ms */
-	udelay (1000);
-
-	/* reset to read mode */
-	addr = (FLASH_WORD_SIZE *) info->start[0];
-	addr[0] = (FLASH_WORD_SIZE) 0x00F000F0;	/* reset bank */
-
-	printf (" done\n");
-	return 0;
-}
-
-/*-----------------------------------------------------------------------
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-
-int write_buff (flash_info_t * info, uchar * src, ulong addr, ulong cnt)
-{
-	ulong cp, wp, data;
-	int i, l, rc;
-
-	wp = (addr & ~3);	/* get lower word aligned address */
-
-	/*
-	 * handle unaligned start bytes
-	 */
-	if ((l = addr - wp) != 0) {
-		data = 0;
-		for (i = 0, cp = wp; i < l; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *) cp);
-		}
-		for (; i < 4 && cnt > 0; ++i) {
-			data = (data << 8) | *src++;
-			--cnt;
-			++cp;
-		}
-		for (; cnt == 0 && i < 4; ++i, ++cp) {
-			data = (data << 8) | (*(uchar *) cp);
-		}
-
-		if ((rc = write_word (info, wp, data)) != 0) {
-			return (rc);
-		}
-		wp += 4;
-	}
-
-	/*
-	 * handle word aligned part
-	 */
-	while (cnt >= 4) {
-		data = 0;
-		for (i = 0; i < 4; ++i) {
-			data = (data << 8) | *src++;
-		}
-		if ((rc = write_word (info, wp, data)) != 0) {
-			return (rc);
-		}
-		wp += 4;
-		cnt -= 4;
-	}
-
-	if (cnt == 0) {
-		return (0);
-	}
-
-	/*
-	 * handle unaligned tail bytes
-	 */
-	data = 0;
-	for (i = 0, cp = wp; i < 4 && cnt > 0; ++i, ++cp) {
-		data = (data << 8) | *src++;
-		--cnt;
-	}
-	for (; i < 4; ++i, ++cp) {
-		data = (data << 8) | (*(uchar *) cp);
-	}
-
-	return (write_word (info, wp, data));
-}
-
-/*-----------------------------------------------------------------------
- * Write a word to Flash, returns:
- * 0 - OK
- * 1 - write timeout
- * 2 - Flash not erased
- */
-static int write_word (flash_info_t * info, ulong dest, ulong data)
-{
-	volatile FLASH_WORD_SIZE *addr2 =
-		(FLASH_WORD_SIZE *) (info->start[0]);
-	volatile FLASH_WORD_SIZE *dest2 = (FLASH_WORD_SIZE *) dest;
-	volatile FLASH_WORD_SIZE *data2 = (FLASH_WORD_SIZE *) & data;
-	ulong start;
-	int i;
-
-	/* Check if Flash is (sufficiently) erased */
-	if ((*((volatile FLASH_WORD_SIZE *) dest) &
-	    (FLASH_WORD_SIZE) data) != (FLASH_WORD_SIZE) data) {
-		return (2);
-	}
-
-	for (i = 0; i < 4 / sizeof (FLASH_WORD_SIZE); i++) {
-		int flag;
-
-		/* Disable interrupts which might cause a timeout here */
-		flag = disable_interrupts ();
-
-		addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00AA00AA;
-		addr2[ADDR1] = (FLASH_WORD_SIZE) 0x00550055;
-		addr2[ADDR0] = (FLASH_WORD_SIZE) 0x00A000A0;
-
-		dest2[i] = data2[i];
-
-		/* re-enable interrupts if necessary */
-		if (flag)
-			enable_interrupts ();
-
-		/* data polling for D7 */
-		start = get_timer (0);
-		while ((dest2[i] & (FLASH_WORD_SIZE) 0x00800080) !=
-		       (data2[i] & (FLASH_WORD_SIZE) 0x00800080)) {
-
-			if (get_timer (start) > CONFIG_SYS_FLASH_WRITE_TOUT) {
-				return (1);
-			}
-		}
-	}
-
-	return (0);
-}
diff --git a/board/jse/host_bridge.c b/board/jse/host_bridge.c
deleted file mode 100644
index 76c07b0c35..0000000000
--- a/board/jse/host_bridge.c
+++ /dev/null
@@ -1,77 +0,0 @@
-/*
- * Copyright (c) 2004 Picture Elements, Inc.
- *    Stephen Williams (steve@icarus.com)
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-#ident "$Id:$"
-
-# include  <common.h>
-# include  <pci.h>
-# include  "jse_priv.h"
-
-/*
- * The JSE board has an Intel 21555 non-transparent bridge for
- * communication with the host. We need to render it harmless on the
- * JSE side, but leave it alone on the host (primary) side. Normally,
- * this will all be done before the host BIOS can gain access to the
- * board, due to the Primary Access Lockout bit.
- *
- * The host_bridge_init function is called as a late initialization
- * function, after most of the board is set up, including a PCI scan.
- */
-
-void host_bridge_init (void)
-{
-	/* The bridge chip is at a fixed location. */
-	pci_dev_t dev = PCI_BDF (0, 10, 0);
-
-	/* Set PCI Class code --
-	   The primary side sees this class code at 0x08 in the
-	   primary config space. This must be something other then a
-	   bridge, or MS Windows starts doing weird stuff to me. */
-	pci_write_config_dword (dev, 0x48, 0x04800000);
-
-	/* Set subsystem ID --
-	   The primary side sees this value at 0x2c. We set it here so
-	   that the host can tell what sort of device this is:
-	   We are a Picture Elements [0x12c5] JSE [0x008a]. */
-	pci_write_config_dword (dev, 0x6c, 0x008a12c5);
-
-	/* Downstream (Primary-to-Secondary) BARs are set up mostly
-	   off. We need only the Memory-0 Bar so that the host can get
-	   at the CSR region to set up tables and the lot. */
-
-	/* Downstream Memory 0 setup (4K for CSR) */
-	pci_write_config_dword (dev, 0xac, 0xfffff000);
-	/* Downstream Memory 1 setup (off) */
-	pci_write_config_dword (dev, 0xb0, 0x00000000);
-	/* Downstream Memory 2 setup (off) */
-	pci_write_config_dword (dev, 0xb4, 0x00000000);
-	/* Downstream Memory 3 setup (off) */
-	pci_write_config_dword (dev, 0xb8, 0x00000000);
-
-	/* Upstream (Secondary-to-Primary) BARs are used to get at
-	   host memory from the JSE card. Create two regions: a small
-	   one to manage individual word reads/writes, and a larger
-	   one for doing bulk frame moves. */
-
-	/* Upstream Memory 0 Setup -- (BAR2) 4K non-prefetchable */
-	pci_write_config_dword (dev, 0xc4, 0xfffff000);
-	/* Upstream Memory 1 setup -- (BAR3) 4K non-prefetchable */
-	pci_write_config_dword (dev, 0xc8, 0xfffff000);
-
-	/* Upstream Memory 2 (BAR4) uses page translation, and is set
-	   up in CCR1. Configure for 4K pages. */
-
-	/* Set CCR1,0 reigsters. This clears the Primary PCI Lockout
-	   bit as well, so we are done configuring after this
-	   point. Therefore, this must be the last step.
-
-	   CC1[15:12]= 0  (disable I2O message unit)
-	   CC1[11:8] = 0x5 (4K page size)
-	   CC0[11]   = 1  (Secondary Clock Disable: disable clock)
-	   CC0[10]   = 0  (Primary Access Lockout: allow primary access)
-	 */
-	pci_write_config_dword (dev, 0xcc, 0x05000800);
-}
diff --git a/board/jse/init.S b/board/jse/init.S
deleted file mode 100644
index 4e449fef20..0000000000
--- a/board/jse/init.S
+++ /dev/null
@@ -1,75 +0,0 @@
-/*
- * SPDX-License-Identifier:	GPL-2.0	IBM-pibs
- */
-/*------------------------------------------------------------------------- */
-/* Function:     ext_bus_cntlr_init */
-/* Description:  Initializes the External Bus Controller for the external */
-/*		peripherals. IMPORTANT: For pass1 this code must run from */
-/*		cache since you can not reliably change a peripheral banks */
-/*		timing register (pbxap) while running code from that bank. */
-/*		For ex., since we are running from ROM on bank 0, we can NOT */
-/*		execute the code that modifies bank 0 timings from ROM, so */
-/*		we run it from cache. */
-/*                                    */
-/*                                    */
-/* The layout for the PEI JSE board:  */
-/*	Bank 0 - Flash and SRAM       */
-/*	Bank 1 - SystemACE            */
-/*	Bank 2 - not used             */
-/*	Bank 3 - not used             */
-/*	Bank 4 - not used             */
-/*	Bank 5 - not used             */
-/*	Bank 6 - not used             */
-/*	Bank 7 - not used             */
-/*------------------------------------------------------------------------- */
-#include <asm/ppc4xx.h>
-
-#include <ppc_asm.tmpl>
-#include <ppc_defs.h>
-
-#include <asm/cache.h>
-#include <asm/mmu.h>
-
-	.globl	ext_bus_cntlr_init
-ext_bus_cntlr_init:
-	mflr    r4                      /* save link register */
-	bl      ..getAddr
-..getAddr:
-	mflr    r3                      /* get address of ..getAddr */
-	mtlr    r4                      /* restore link register */
-	addi    r4,0,14                 /* set ctr to 10; used to prefetch */
-	mtctr   r4                      /* 10 cache lines to fit this function */
-					/* in cache (gives us 8x10=80 instrctns) */
-..ebcloop:
-	icbt    r0,r3                   /* prefetch cache line for addr in r3 */
-	addi    r3,r3,32		/* move to next cache line */
-	bdnz    ..ebcloop               /* continue for 10 cache lines */
-
-	/*----------------------------------------------------------------- */
-	/* Delay to ensure all accesses to ROM are complete before changing */
-	/* bank 0 timings. 200usec should be enough. */
-	/*   200,000,000 (cycles/sec) X .000200 (sec) = 0x9C40 cycles */
-	/*----------------------------------------------------------------- */
-	addis	r3,0,0x0
-	ori     r3,r3,0xA000          /* ensure 200usec have passed since reset */
-	mtctr   r3
-..spinlp:
-	bdnz    ..spinlp                /* spin loop */
-
-	/*----------------------------------------------------------------- */
-	/* Memory Bank 0 (Flash) initialization */
-	/*----------------------------------------------------------------- */
-
-	addi    r4,0,PB1AP
-	mtdcr   EBC0_CFGADDR,r4
-	addis   r4,0,0x9B01
-	ori     r4,r4,0x5480
-	mtdcr   EBC0_CFGDATA,r4
-
-	addi    r4,0,PB0CR
-	mtdcr   EBC0_CFGADDR,r4
-	addis   r4,0,0xFFF1           /* BAS=0xFFF,BS=0x0(1MB),BU=0x3(R/W), */
-	ori     r4,r4,0x8000          /* BW=0x0( 8 bits) */
-	mtdcr   EBC0_CFGDATA,r4
-
-	blr
diff --git a/board/jse/jse.c b/board/jse/jse.c
deleted file mode 100644
index a0913c33f0..0000000000
--- a/board/jse/jse.c
+++ /dev/null
@@ -1,147 +0,0 @@
-/*
- * Copyright (c) 2004 Picture Elements, Inc.
- *    Stephen Williams (steve@icarus.com)
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-# include  <common.h>
-# include  <asm/ppc4xx.h>
-# include  <asm/processor.h>
-# include  <asm/io.h>
-# include  "jse_priv.h"
-
-/*
- * This function is run very early, out of flash, and before devices are
- * initialized. It is called by arch/powerpc/lib/board.c:board_init_f by virtue
- * of being in the init_sequence array.
- *
- * The SDRAM has been initialized already -- start.S:start called
- * init.S:init_sdram early on -- but it is not yet being used for
- * anything, not even stack. So be careful.
- */
-int board_early_init_f (void)
-{
-   /*-------------------------------------------------------------------------+
-   | Interrupt controller setup for the JSE board.
-   | Note: IRQ 0-15  405GP internally generated; active high; level sensitive
-   |       IRQ 16    405GP internally generated; active low; level sensitive
-   |       IRQ 17-24 RESERVED/UNUSED
-   |       IRQ 25 (EXT IRQ 0) PCI SLOT 0; active low; level sensitive
-   |       IRQ 26 (EXT IRQ 1) PCI SLOT 1; active low; level sensitive
-   |       IRQ 27 (EXT IRQ 2) JP2C CHIP ; active low; level sensitive
-   |       IRQ 28 (EXT IRQ 3) PCI bridge; active low; level sensitive
-   |       IRQ 29 (EXT IRQ 4) SystemACE IRQ; active high
-   |       IRQ 30 (EXT IRQ 5) SystemACE BRdy (unused)
-   |       IRQ 31 (EXT IRQ 6) (unused)
-   +-------------------------------------------------------------------------*/
-	mtdcr (UIC0SR, 0xFFFFFFFF);	/* clear all ints */
-	mtdcr (UIC0ER, 0x00000000);	/* disable all ints */
-	mtdcr (UIC0CR, 0x00000000);	/* set all to be non-critical */
-	mtdcr (UIC0PR, 0xFFFFFF87);	/* set int polarities */
-	mtdcr (UIC0TR, 0x10000000);	/* set int trigger levels */
-	mtdcr (UIC0SR, 0xFFFFFFFF);	/* clear all ints */
-
-	/* Configure the interface to the SystemACE MCU port.
-	   The SystemACE is fast, but there is no reason to have
-	   excessivly tight timings. So the settings are slightly
-	   generous. */
-
-	/* EBC0_B1AP: BME=1, TWT=2, CSN=0, OEN=1,
-	   WBN=0, WBF=1, TH=0,  RE=0,  SOR=0, BEM=0, PEN=0 */
-	mtdcr (EBC0_CFGADDR, PB1AP);
-	mtdcr (EBC0_CFGDATA, 0x01011000);
-
-	/* EBC0_B1CR: BAS=x, BS=0(1MB), BU=3(R/W), BW=0(8bits) */
-	mtdcr (EBC0_CFGADDR, PB1CR);
-	mtdcr (EBC0_CFGDATA, CONFIG_SYS_SYSTEMACE_BASE | 0x00018000);
-
-	/* Enable the /PerWE output as /PerWE, instead of /PCIINT. */
-	/* CPC0_CR1 |= PCIPW */
-	mtdcr (0xb2, mfdcr (0xb2) | 0x00004000);
-
-	return 0;
-}
-
-#ifdef CONFIG_BOARD_PRE_INIT
-int board_pre_init (void)
-{
-	return board_early_init_f ();
-}
-
-#endif
-
-/*
- * This function is also called by arch/powerpc/lib/board.c:board_init_f (it is
- * also in the init_sequence array) but later. Many more things are
- * configured, but we are still running from flash.
- */
-int checkboard (void)
-{
-	unsigned vers, status;
-
-	/* check that the SystemACE chip is alive. */
-	printf ("ACE:   ");
-	vers = readw (CONFIG_SYS_SYSTEMACE_BASE + 0x16);
-	printf ("SystemACE %u.%u (build %u)",
-		(vers >> 12) & 0x0f, (vers >> 8) & 0x0f, vers & 0xff);
-
-	status = readl (CONFIG_SYS_SYSTEMACE_BASE + 0x04);
-#ifdef DEBUG
-	printf (" STATUS=0x%08x", status);
-#endif
-	/* If the flash card is present and there is an initial error,
-	   then force a restart of the program. */
-	if (status & 0x00000010) {
-		printf (" CFDETECT");
-
-		if (status & 0x04) {
-			/* CONTROLREG = CFGPROG */
-			writew (0x1000, CONFIG_SYS_SYSTEMACE_BASE + 0x18);
-			udelay (500);
-			/* CONTROLREG = CFGRESET */
-			writew (0x0080, CONFIG_SYS_SYSTEMACE_BASE + 0x18);
-			udelay (500);
-			writew (0x0000, CONFIG_SYS_SYSTEMACE_BASE + 0x18);
-			/* CONTROLREG = CFGSTART */
-			writew (0x0020, CONFIG_SYS_SYSTEMACE_BASE + 0x18);
-
-			status = readl (CONFIG_SYS_SYSTEMACE_BASE + 0x04);
-		}
-	}
-
-	/* Wait for the SystemACE to program its chain of devices. */
-	while ((status & 0x84) == 0x00) {
-		udelay (500);
-		status = readl (CONFIG_SYS_SYSTEMACE_BASE + 0x04);
-	}
-
-	if (status & 0x04)
-		printf (" CFG-ERROR");
-	if (status & 0x80)
-		printf (" CFGDONE");
-
-	printf ("\n");
-
-	/* Force /RTS to active. The board it not wired quite
-	   correctly to use cts/rtc flow control, so just force the
-	   /RST active and forget about it. */
-	writeb (readb (0xef600404) | 0x03, 0xef600404);
-
-	printf ("JSE:   ready\n");
-
-	return 0;
-}
-
-/* **** No more functions called by board_init_f. **** */
-
-/*
- * This function is called by arch/powerpc/lib/board.c:board_init_r. At this
- * point, basic setup is done, U-Boot has been moved into SDRAM and
- * PCI has been set up. From here we done late setup.
- */
-int misc_init_r (void)
-{
-	host_bridge_init ();
-	return 0;
-}
diff --git a/board/jse/jse_priv.h b/board/jse/jse_priv.h
deleted file mode 100644
index f61204bbae..0000000000
--- a/board/jse/jse_priv.h
+++ /dev/null
@@ -1,12 +0,0 @@
-#ifndef __jse_priv_H
-#define __jse_prov_H
-/*
- * Copyright (c) 2004 Picture Elements, Inc.
- *    Stephen Williams (steve@icarus.com)
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-extern void host_bridge_init(void);
-
-#endif
diff --git a/board/jse/sdram.c b/board/jse/sdram.c
deleted file mode 100644
index 5639beddce..0000000000
--- a/board/jse/sdram.c
+++ /dev/null
@@ -1,169 +0,0 @@
-/*
- * Copyright (c) 2004 Picture Elements, Inc.
- *    Stephen Williams (steve@icarus.com)
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <asm/ppc4xx.h>
-#include <asm/processor.h>
-
-# define SDRAM_LEN 0x08000000
-
-/*
- * this is even after checkboard. It returns the size of the SDRAM
- * that we have installed. This function is called by board_init_f
- * in arch/powerpc/lib/board.c to initialize the memory and return what I
- * found.
- */
-phys_size_t initdram (int board_type)
-{
-	/* Configure the SDRAMS */
-
-	/* disable memory controller */
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
-	mtdcr (SDRAM0_CFGDATA, 0x00000000);
-
-	udelay (500);
-
-	/* Clear SDRAM0_BESR0 (Bus Error Syndrome Register) */
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_BESR0);
-	mtdcr (SDRAM0_CFGDATA, 0xffffffff);
-
-	/* Clear SDRAM0_BESR1 (Bus Error Syndrome Register) */
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_BESR1);
-	mtdcr (SDRAM0_CFGDATA, 0xffffffff);
-
-	/* Clear SDRAM0_ECCCFG (disable ECC) */
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCCFG);
-	mtdcr (SDRAM0_CFGDATA, 0x00000000);
-
-	/* Clear SDRAM0_ECCESR (ECC Error Syndrome Register) */
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_ECCESR);
-	mtdcr (SDRAM0_CFGDATA, 0xffffffff);
-
-	/* Timing register: CASL=2, PTA=2, CTP=2, LDF=1, RFTA=5, RCD=2 */
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_TR);
-	mtdcr (SDRAM0_CFGDATA, 0x010a4016);
-
-	/* Memory Bank 0 Config == BA=0x00000000, SZ=64M, AM=3, BE=1 */
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
-	mtdcr (SDRAM0_CFGDATA, 0x00084001);
-
-	/* Memory Bank 1 Config == BA=0x04000000, SZ=64M, AM=3, BE=1 */
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
-	mtdcr (SDRAM0_CFGDATA, 0x04084001);
-
-	/* Memory Bank 2 Config ==  BE=0 */
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_B2CR);
-	mtdcr (SDRAM0_CFGDATA, 0x00000000);
-
-	/* Memory Bank 3 Config ==  BE=0 */
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_B3CR);
-	mtdcr (SDRAM0_CFGDATA, 0x00000000);
-
-	/* refresh timer = 0x400  */
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
-	mtdcr (SDRAM0_CFGDATA, 0x04000000);
-
-	/* Power management idle timer set to the default. */
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_PMIT);
-	mtdcr (SDRAM0_CFGDATA, 0x07c00000);
-
-	udelay (500);
-
-	/* Enable banks (DCE=1, BPRF=1, ECCDD=1, EMDUL=1) */
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
-	mtdcr (SDRAM0_CFGDATA, 0x80e00000);
-
-	return SDRAM_LEN;
-}
-
-/*
- * The U-Boot core, as part of the initialization to prepare for
- * loading the monitor into SDRAM, requests of this function that the
- * memory be tested. Return 0 if the memory tests OK.
- */
-int testdram (void)
-{
-	unsigned long idx;
-	unsigned val;
-	unsigned errors;
-	volatile unsigned long *sdram;
-
-#ifdef DEBUG
-	printf ("SDRAM Controller Registers --\n");
-
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_CFG);
-	val = mfdcr (SDRAM0_CFGDATA);
-	printf ("    SDRAM0_CFG   : 0x%08x\n", val);
-
-	mtdcr (SDRAM0_CFGADDR, 0x24);
-	val = mfdcr (SDRAM0_CFGDATA);
-	printf ("    SDRAM0_STATUS: 0x%08x\n", val);
-
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_B0CR);
-	val = mfdcr (SDRAM0_CFGDATA);
-	printf ("    SDRAM0_B0CR  : 0x%08x\n", val);
-
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_B1CR);
-	val = mfdcr (SDRAM0_CFGDATA);
-	printf ("    SDRAM0_B1CR  : 0x%08x\n", val);
-
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_TR);
-	val = mfdcr (SDRAM0_CFGDATA);
-	printf ("    SDRAM0_TR    : 0x%08x\n", val);
-
-	mtdcr (SDRAM0_CFGADDR, SDRAM0_RTR);
-	val = mfdcr (SDRAM0_CFGDATA);
-	printf ("    SDRAM0_RTR   : 0x%08x\n", val);
-#endif
-
-	/* Wait for memory to be ready by testing MRSCMPbit
-	   bit. Really, there should already have been plenty of time,
-	   given it was started long ago. But, best to check. */
-	for (idx = 0; idx < 1000000; idx += 1) {
-		mtdcr (SDRAM0_CFGADDR, 0x24);
-		val = mfdcr (SDRAM0_CFGDATA);
-		if (val & 0x80000000)
-			break;
-	}
-
-	if (!(val & 0x80000000)) {
-		printf ("SDRAM ERROR: SDRAM0_STATUS never set!\n");
-		return 1;
-	}
-
-	/* Start memory test. */
-	printf ("test: %u MB - ", SDRAM_LEN / 1048576);
-
-	sdram = (unsigned long *) CONFIG_SYS_SDRAM_BASE;
-
-	printf ("write - ");
-	for (idx = 2; idx < SDRAM_LEN / 4; idx += 2) {
-		sdram[idx + 0] = idx;
-		sdram[idx + 1] = ~idx;
-	}
-
-	printf ("read - ");
-	errors = 0;
-	for (idx = 2; idx < SDRAM_LEN / 4; idx += 2) {
-		if (sdram[idx + 0] != idx)
-			errors += 1;
-		if (sdram[idx + 1] != ~idx)
-			errors += 1;
-		if (errors > 0)
-			break;
-	}
-
-	if (errors > 0) {
-		printf ("NOT OK\n");
-		printf ("FIRST ERROR at %p: 0x%08lx:0x%08lx != 0x%08lx:0x%08lx\n",
-			sdram + idx, sdram[idx + 0], sdram[idx + 1], idx, ~idx);
-		return 1;
-	}
-
-	printf ("ok\n");
-	return 0;
-}
diff --git a/configs/JSE_defconfig b/configs/JSE_defconfig
deleted file mode 100644
index 14c9c2feea..0000000000
--- a/configs/JSE_defconfig
+++ /dev/null
@@ -1,3 +0,0 @@
-CONFIG_PPC=y
-CONFIG_4xx=y
-CONFIG_TARGET_JSE=y
diff --git a/doc/README.scrapyard b/doc/README.scrapyard
index 481f4d8fdd..668431c57a 100644
--- a/doc/README.scrapyard
+++ b/doc/README.scrapyard
@@ -12,6 +12,7 @@ The list should be sorted in reverse chronological order.
 
 Board            Arch        CPU            Commit      Removed     Last known maintainer/contact
 =================================================================================================
+JSE              powerpc     ppc4xx         -           -           Stephen Williams <steve@icarus.com>
 BC3450           powerpc     mpc5xxx        -           -
 hawkboard        arm         arm926ejs      cb957cda    2015-02-24  Syed Mohammed Khasim <sm.khasim@gmail.com>:Sughosh Ganu <urwithsughosh@gmail.com>
 tnetv107x        arm         arm1176        50b82c4b    2015-02-24  Chan-Taek Park <c-park@ti.com>
diff --git a/include/configs/JSE.h b/include/configs/JSE.h
deleted file mode 100644
index 5cc25576ae..0000000000
--- a/include/configs/JSE.h
+++ /dev/null
@@ -1,276 +0,0 @@
-/*
- * (C) Copyright 2003 Picture Elements, Inc.
- * Stephen Williams <steve@icarus.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-/*
- * board/config.h - configuration options, board specific
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-/*
- * High Level Configuration Options for the JSE board
- * (Theoretically easy to change, but the board is fixed.)
- */
-
-#define CONFIG_JSE 1
-  /* JSE has a PPC405GPr */
-#define CONFIG_405GP 1
-  /* ... with a 33MHz OSC. connected to the SysCLK input */
-#define CONFIG_SYS_CLK_FREQ	33333333
-  /* ... with on-chip memory here (4KBytes) */
-#define CONFIG_SYS_OCM_DATA_ADDR 0xF4000000
-#define CONFIG_SYS_OCM_DATA_SIZE 0x00001000
-  /* Do not set up locked dcache as init ram. */
-#undef CONFIG_SYS_INIT_DCACHE_CS
-
-#define	CONFIG_SYS_TEXT_BASE	0xFFF80000
-
-  /* Map the SystemACE chip (CS#1) here. (Must be a multiple of 1Meg) */
-#define CONFIG_SYSTEMACE 1
-#define CONFIG_SYS_SYSTEMACE_BASE 0xf0000000
-#define CONFIG_SYS_SYSTEMACE_WIDTH 8
-#define CONFIG_DOS_PARTITION 1
-
-  /* Use the On-Chip-Memory (OCM) as a temporary stack for the startup code. */
-#define CONFIG_SYS_TEMP_STACK_OCM 1
-  /* ... place INIT RAM in the OCM address */
-# define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR
-  /* ... give it the whole init ram */
-# define CONFIG_SYS_INIT_RAM_SIZE	CONFIG_SYS_OCM_DATA_SIZE
-  /* ... Shave a bit off the end for global data */
-# define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
-  /* ... and place the stack pointer at the top of what's left. */
-# define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
-
-  /* Enable board_pre_init function */
-#define CONFIG_BOARD_PRE_INIT	1
-#define CONFIG_BOARD_EARLY_INIT_F 1
-  /* Disable post-clk setup init function */
-#undef CONFIG_BOARD_POSTCLK_INIT
-  /* Disable call to post_init_f: late init function. */
-#undef CONFIG_POST
-  /* Enable DRAM test. */
-#define CONFIG_SYS_DRAM_TEST 1
-  /* Enable misc_init_r function. */
-#define CONFIG_MISC_INIT_R 1
-
-  /* JSE has EEPROM chips that are good for environment. */
-#undef	CONFIG_ENV_IS_IN_NVRAM
-#undef	CONFIG_ENV_IS_IN_FLASH
-#define CONFIG_ENV_IS_IN_EEPROM 1
-#undef	CONFIG_ENV_IS_NOWHERE
-
-  /* This is the 7bit address of the device, not including P. */
-#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
-  /* After the device address, need one more address byte. */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
-  /* The EEPROM is 512 bytes. */
-#define CONFIG_SYS_EEPROM_SIZE 512
-  /* The EEPROM can do 16byte ( 1 << 4 ) page writes. */
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10
-  /* Put the environment in the second half. */
-#define CONFIG_ENV_OFFSET	0x00
-#define CONFIG_ENV_SIZE	512
-
-  /* The JSE connects UART1 to the console tap connector. */
-#define CONFIG_CONS_INDEX	2
-#define CONFIG_SYS_NS16550
-#define CONFIG_SYS_NS16550_SERIAL
-#define CONFIG_SYS_NS16550_REG_SIZE	1
-#define CONFIG_SYS_NS16550_CLK		get_serial_clock()
-
-  /* Set console baudrate to 9600 */
-#define CONFIG_BAUDRATE		9600
-
-/*
- * Configuration related to auto-boot.
- *
- * CONFIG_BOOTDELAY sets the delay (in seconds) that U-Boot will wait
- * before resorting to autoboot. This value can be overridden by the
- * bootdelay environment variable.
- *
- * CONFIG_AUTOBOOT_PROMPT is the string that U-Boot emits to warn the
- * user that an autoboot will happen.
- *
- * CONFIG_BOOTCOMMAND is the sequence of commands that U-Boot will
- * execute to boot the JSE. This loads the uimage and initrd.img files
- * from CompactFlash into memory, then boots them from memory.
- *
- * CONFIG_BOOTARGS is the arguments passed to the Linux kernel to get
- * it going on the JSE.
- */
-#define CONFIG_BOOTDELAY	5
-#define CONFIG_BOOTARGS		"root=/dev/ram0 init=/linuxrc rw"
-#define CONFIG_BOOTCOMMAND	"fatload ace 0 2000000 uimage; fatload ace 0 2100000 initrd.img; bootm 2000000 2100000"
-
-
-#define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
-#define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change	*/
-
-#define CONFIG_PPC4xx_EMAC
-#define CONFIG_MII		1	/* MII PHY management		*/
-#define CONFIG_PHY_ADDR		1	/* PHY address			*/
-
-
-/*
- * BOOTP options
- */
-#define CONFIG_BOOTP_BOOTFILESIZE
-#define CONFIG_BOOTP_BOOTPATH
-#define CONFIG_BOOTP_GATEWAY
-#define CONFIG_BOOTP_HOSTNAME
-
-
-/*
- * Command line configuration.
- */
-#include <config_cmd_default.h>
-
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_EEPROM
-#define CONFIG_CMD_ELF
-#define CONFIG_CMD_FAT
-#define CONFIG_CMD_FLASH
-#define CONFIG_CMD_IRQ
-#define CONFIG_CMD_MII
-#define CONFIG_CMD_NET
-#define CONFIG_CMD_PCI
-#define CONFIG_CMD_PING
-
-
-  /* watchdog disabled */
-#undef CONFIG_WATCHDOG
-  /* SPD EEPROM (sdram speed config) disabled */
-#undef CONFIG_SPD_EEPROM
-#undef SPD_EEPROM_ADDRESS
-
-/*
- * Miscellaneous configurable options
- */
-#define CONFIG_SYS_LONGHELP			/* undef to save memory		*/
-
-#define CONFIG_SYS_HUSH_PARSER			/* use "hush" command parser	*/
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_SYS_CBSIZE	1024		/* Console I/O Buffer Size	*/
-#else
-#define CONFIG_SYS_CBSIZE	256		/* Console I/O Buffer Size	*/
-#endif
-#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
-#define CONFIG_SYS_MAXARGS	16		/* max number of command args	*/
-#define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
-
-#define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
-#define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/
-
-/*
- * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
- * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
- * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
- * The Linux BASE_BAUD define should match this configuration.
- *    baseBaud = cpuClock/(uartDivisor*16)
- * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
- * set Linux BASE_BAUD to 403200.
- */
-#undef	CONFIG_SYS_EXT_SERIAL_CLOCK	       /* external serial clock */
-#undef	CONFIG_SYS_405_UART_ERRATA_59	       /* 405GP/CR Rev. D silicon */
-#define CONFIG_SYS_BASE_BAUD	    691200
-
-/* The following table includes the supported baudrates */
-#define CONFIG_SYS_BAUDRATE_TABLE  \
-    {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 57600, 115200, 230400}
-
-#define CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address */
-#define CONFIG_SYS_EXTBDINFO		1	/* To use extended board_into (bd_t) */
-
-#define CONFIG_SYS_I2C
-#define CONFIG_SYS_I2C_PPC4XX
-#define CONFIG_SYS_I2C_PPC4XX_CH0
-#define CONFIG_SYS_I2C_PPC4XX_SPEED_0		400000
-#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0		0x7F
-
-
-/*-----------------------------------------------------------------------
- * PCI stuff
- *-----------------------------------------------------------------------
- */
-#define PCI_HOST_ADAPTER 0		/* configure ar pci adapter	*/
-#define PCI_HOST_FORCE	1		/* configure as pci host	*/
-#define PCI_HOST_AUTO	2		/* detected via arbiter enable	*/
-
-#define CONFIG_PCI			/* include pci support		*/
-#define CONFIG_PCI_INDIRECT_BRIDGE	/* indirect PCI bridge support */
-#define CONFIG_PCI_HOST PCI_HOST_FORCE	/* select pci host function	*/
-#undef	CONFIG_PCI_PNP			/* do pci plug-and-play		*/
-					/* resource configuration	*/
-
-#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x0000	/* PCI Vendor ID: to-do!!!	*/
-#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0000	/* PCI Device ID: to-do!!!	*/
-#define CONFIG_SYS_PCI_PTM1LA	0x00000000	/* point to sdram		*/
-#define CONFIG_SYS_PCI_PTM1MS	0x80000001	/* 2GB, enable hard-wired to 1	*/
-#define CONFIG_SYS_PCI_PTM1PCI 0x00000000	/* Host: use this pci address	*/
-#define CONFIG_SYS_PCI_PTM2LA	0x00000000	/* disabled			*/
-#define CONFIG_SYS_PCI_PTM2MS	0x00000000	/* disabled			*/
-#define CONFIG_SYS_PCI_PTM2PCI 0x04000000	/* Host: use this pci address	*/
-
-/*-----------------------------------------------------------------------
- * External peripheral base address
- *-----------------------------------------------------------------------
- */
-#undef	CONFIG_IDE_LED			/* no led for ide supported	*/
-#undef	CONFIG_IDE_RESET		/* no reset for ide supported	*/
-
-#define CONFIG_SYS_KEY_REG_BASE_ADDR	0xF0100000
-#define CONFIG_SYS_IR_REG_BASE_ADDR	0xF0200000
-#define CONFIG_SYS_FPGA_REG_BASE_ADDR	0xF0300000
-
-/*-----------------------------------------------------------------------
- * Start addresses for the final memory configuration
- * (Set up by the startup code)
- * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
- */
-#define CONFIG_SYS_SDRAM_BASE		0x00000000
-#define CONFIG_SYS_FLASH_BASE		0xFFF80000
-#define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
-#define CONFIG_SYS_MONITOR_LEN		(256 * 1024)	/* Reserve 256 kB for Monitor	*/
-#define CONFIG_SYS_MALLOC_LEN		(128 * 1024)	/* Reserve 128 kB for malloc()	*/
-
-/*
- * For booting Linux, the board info and command line data
- * have to be in the first 8 MB of memory, since this is
- * the maximum mapped by the Linux kernel during initialization.
- */
-#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
-
-/*-----------------------------------------------------------------------
- * FLASH organization
- */
-#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip	*/
-
-#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
-
-/*
- * Init Memory Controller:
- *
- * BR0/1 and OR0/1 (FLASH)
- */
-
-#define FLASH_BASE0_PRELIM	CONFIG_SYS_FLASH_BASE	/* FLASH bank #0	*/
-#define FLASH_BASE1_PRELIM	0		/* FLASH bank #1	*/
-
-
-/* Configuration Port location */
-#define CONFIG_PORT_ADDR	0xF0000500
-
-#if defined(CONFIG_CMD_KGDB)
-#define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
-#endif
-#endif	/* __CONFIG_H */