arm: Remove wireless_space board

This board has not been converted to generic board by the deadline.
Remove it.

Signed-off-by: Simon Glass <sjg@chromium.org>

8 files changed, 0 insertions, 455 deletions

diff --git a/arch/arm/mach-kirkwood/Kconfig b/arch/arm/mach-kirkwood/Kconfig
index c053602a50..aab5d19b5f 100644
--- a/arch/arm/mach-kirkwood/Kconfig
+++ b/arch/arm/mach-kirkwood/Kconfig
@@ -34,9 +34,6 @@ config TARGET_NET2BIG_V2
 config TARGET_NETSPACE_V2
 	bool "LaCie netspace_v2 Board"
 
-config TARGET_WIRELESS_SPACE
-	bool "LaCie Wireless_space Board"
-
 config TARGET_IB62X0
 	bool "ib62x0 Board"
 
@@ -64,7 +61,6 @@ source "board/iomega/iconnect/Kconfig"
 source "board/keymile/km_arm/Kconfig"
 source "board/LaCie/net2big_v2/Kconfig"
 source "board/LaCie/netspace_v2/Kconfig"
-source "board/LaCie/wireless_space/Kconfig"
 source "board/raidsonic/ib62x0/Kconfig"
 source "board/Seagate/dockstar/Kconfig"
 source "board/Seagate/goflexhome/Kconfig"
diff --git a/board/LaCie/wireless_space/Kconfig b/board/LaCie/wireless_space/Kconfig
deleted file mode 100644
index 75a2fc5a75..0000000000
--- a/board/LaCie/wireless_space/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_WIRELESS_SPACE
-
-config SYS_BOARD
-	default "wireless_space"
-
-config SYS_VENDOR
-	default "LaCie"
-
-config SYS_CONFIG_NAME
-	default "wireless_space"
-
-endif
diff --git a/board/LaCie/wireless_space/MAINTAINERS b/board/LaCie/wireless_space/MAINTAINERS
deleted file mode 100644
index c32ecb8b73..0000000000
--- a/board/LaCie/wireless_space/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-WIRELESS_SPACE BOARD
-M:	Albert ARIBAUD <albert.u.boot@aribaud.net>
-S:	Maintained
-F:	board/LaCie/wireless_space/
-F:	include/configs/wireless_space.h
-F:	configs/wireless_space_defconfig
diff --git a/board/LaCie/wireless_space/Makefile b/board/LaCie/wireless_space/Makefile
deleted file mode 100644
index 90a84f4892..0000000000
--- a/board/LaCie/wireless_space/Makefile
+++ /dev/null
@@ -1,12 +0,0 @@
-#
-# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
-#
-# Based on Kirkwood support:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-
-obj-y	:= wireless_space.o ../common/common.o
diff --git a/board/LaCie/wireless_space/kwbimage.cfg b/board/LaCie/wireless_space/kwbimage.cfg
deleted file mode 100644
index 037248b3c6..0000000000
--- a/board/LaCie/wireless_space/kwbimage.cfg
+++ /dev/null
@@ -1,71 +0,0 @@
-#
-# Copyright (C) 2012 Albert ARIBAUD <albert.u.boot@aribaud.net>
-#
-# Based on netspace_v2 kwbimage.cfg:
-# Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
-#
-# Based on Kirkwood support:
-# (C) Copyright 2009
-# Marvell Semiconductor <www.marvell.com>
-# Written-by: Prafulla Wadaskar <prafulla@marvell.com>
-#
-# SPDX-License-Identifier:	GPL-2.0+
-#
-# Refer doc/README.kwbimage for more details about how-to configure
-# and create kirkwood boot image
-#
-
-# Boot Media configurations
-BOOT_FROM	nand	# Boot from NAND flash
-NAND_PAGE_SIZE 800
-
-# SOC registers configuration using bootrom header extension
-# Maximum KWBIMAGE_MAX_CONFIG configurations allowed
-
-# Values taken from image original LaCie U-Boot header dump!
-
-# Configure RGMII-0 interface pad voltage to 1.8V
-DATA 0xFFD100e0 0x1B1B1B9B
-
-#Dram initalization for SINGLE x16 CL=5 @ 400MHz
-DATA 0xFFD01400 0x43000c30	# DDR Configuration register
-
-DATA 0xFFD01404 0x37743000	# DDR Controller Control Low
-
-DATA 0xFFD01408 0x11012228	# DDR Timing (Low) (active cycles value +1)
-
-DATA 0xFFD0140C 0x00000A19	#  DDR Timing (High)
-
-DATA 0xFFD01410 0x0000CCCC	#  DDR Address Control
-
-DATA 0xFFD01414 0x00000000	#  DDR Open Pages Control
-
-DATA 0xFFD01418 0x00000000	#  DDR Operation
-
-DATA 0xFFD0141C 0x00000662	#  DDR Mode
-
-DATA 0xFFD01420 0x00000004	#  DDR Extended Mode
-
-DATA 0xFFD01424 0x0000F07F	#  DDR Controller Control High
-
-DATA 0xFFD01428 0x00096630	# DDR2 ODT Read Timing (default values)
-
-DATA 0xFFD0147C 0x00009663	# DDR2 ODT Write Timing (default values)
-
-DATA 0xFFD01504 0x0FFFFFF1	# CS[0]n Size
-DATA 0xFFD01508 0x00000000	# CS[1]n Base address to 0x0
-DATA 0xFFD0150C 0x00000000	# CS[1]n Size, window disabled
-DATA 0xFFD01514 0x00000000	# CS[2]n Size, window disabled
-DATA 0xFFD0151C 0x00000000	# CS[3]n Size, window disabled
-DATA 0xFFD01494 0x00120012	#  DDR ODT Control (Low)
-DATA 0xFFD01498 0x00000000	#  DDR ODT Control (High)
-DATA 0xFFD0149C 0x0000E40F	# CPU ODT Control
-DATA 0xFFD01480 0x00000001	# DDR Initialization Control
-DATA 0xFFD20134 0x66666666
-DATA 0xFFD20138 0x66666666
-DATA 0xFFD10000 0x01112222
-DATA 0xFFD1000C 0x00000000
-DATA 0xFFD10104 0x00000000
-DATA 0xFFD10100 0x40000000
-# End of Header extension
-DATA 0x0 0x0
diff --git a/board/LaCie/wireless_space/wireless_space.c b/board/LaCie/wireless_space/wireless_space.c
deleted file mode 100644
index 8620e4b5d1..0000000000
--- a/board/LaCie/wireless_space/wireless_space.c
+++ /dev/null
@@ -1,165 +0,0 @@
-/*
- * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
- *
- * Based on Kirkwood support:
- * (C) Copyright 2009
- * Marvell Semiconductor <www.marvell.com>
- * Written-by: Prafulla Wadaskar <prafulla@marvell.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#include <common.h>
-#include <command.h>
-#include <asm/arch/cpu.h>
-#include <asm/arch/soc.h>
-#include <asm/arch/mpp.h>
-#include <asm/arch/gpio.h>
-
-#include "../common/common.h"
-#include "netdev.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/* GPIO configuration: start FAN at low speed, USB and HDD */
-
-#define WIRELESS_SPACE_OE_LOW		0xFF006808
-#define WIRELESS_SPACE_OE_HIGH		0x0000F989
-#define WIRELESS_SPACE_OE_VAL_LOW	0x00010080
-#define WIRELESS_SPACE_OE_VAL_HIGH	0x00000240
-
-#define WIRELESS_SPACE_REAR_BUTTON	13
-#define WIRELESS_SPACE_FRONT_BUTTON	43
-
-const u32 kwmpp_config[] = {
-	MPP0_NF_IO2,
-	MPP1_NF_IO3,
-	MPP2_NF_IO4,
-	MPP3_NF_IO5,
-	MPP4_NF_IO6,
-	MPP5_NF_IO7,
-	MPP6_SYSRST_OUTn,
-	MPP7_GPO,		/* Fan speed (bit 1) */
-	MPP8_TW_SDA,
-	MPP9_TW_SCK,
-	MPP10_UART0_TXD,
-	MPP11_UART0_RXD,
-	MPP13_GPIO,		/* Red led */
-	MPP14_GPIO,		/* USB fuse */
-	MPP15_SATA0_ACTn,
-	MPP16_GPIO,		/* SATA 0 power */
-	MPP17_GPIO,		/* SATA 1 power */
-	MPP18_NF_IO0,
-	MPP19_NF_IO1,
-	MPP20_GE1_0,		/* Gigabit Ethernet 1 */
-	MPP21_GE1_1,
-	MPP22_GE1_2,
-	MPP23_GE1_3,
-	MPP24_GE1_4,
-	MPP25_GE1_5,
-	MPP26_GE1_6,
-	MPP27_GE1_7,
-	MPP28_GE1_8,
-	MPP29_GE1_9,
-	MPP30_GE1_10,
-	MPP31_GE1_11,
-	MPP32_GE1_12,
-	MPP33_GE1_13,
-	MPP34_GE1_14,
-	MPP35_GE1_15,
-	MPP36_GPIO,		/* Fan speed (bit 2) */
-	MPP37_GPIO,		/* Fan speed (bit 0) */
-	MPP38_GPIO,		/* Fan power */
-	MPP39_GPIO,		/* Fan rotation fail */
-	MPP40_GPIO,		/* Ethernet switch link */
-	MPP41_GPIO,		/* USB enable host vbus */
-	MPP42_GPIO,		/* LED clock control */
-	MPP43_GPIO,		/* WPS button (0=Pushed, 1=Released) */
-	MPP44_GPIO,		/* Red LED on/off */
-	MPP45_GPIO,		/* Red LED timer blink (on=off=100ms) */
-	MPP46_GPIO,		/* Green LED on/off */
-	MPP47_GPIO,		/* LED (blue, green) SATA activity blink */
-	MPP48_GPIO,		/* Blue LED on/off */
-	0
-};
-
-struct mv88e61xx_config swcfg = {
-	.name = "egiga0",
-	.vlancfg = MV88E61XX_VLANCFG_ROUTER,
-	.rgmii_delay = MV88E61XX_RGMII_DELAY_EN,
-	.led_init = MV88E61XX_LED_INIT_EN,
-	.mdip = MV88E61XX_MDIP_NOCHANGE,
-	.portstate = MV88E61XX_PORTSTT_FORWARDING,
-	.cpuport = 0x20,
-	.ports_enabled = 0x3F,
-};
-
-int board_early_init_f(void)
-{
-	/* Gpio configuration */
-	mvebu_config_gpio(WIRELESS_SPACE_OE_VAL_LOW, WIRELESS_SPACE_OE_VAL_HIGH,
-			  WIRELESS_SPACE_OE_LOW, WIRELESS_SPACE_OE_HIGH);
-
-	/* Multi-Purpose Pins Functionality configuration */
-	kirkwood_mpp_conf(kwmpp_config, NULL);
-
-	return 0;
-}
-
-int board_init(void)
-{
-	/* Machine number */
-	gd->bd->bi_arch_number = CONFIG_MACH_TYPE;
-
-	/* Boot parameters address */
-	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;
-
-	return 0;
-}
-
-#if defined(CONFIG_MISC_INIT_R)
-int misc_init_r(void)
-{
-#if defined(CONFIG_CMD_I2C) && defined(CONFIG_SYS_I2C_EEPROM_ADDR)
-	if (!getenv("ethaddr")) {
-		uchar mac[6];
-		if (lacie_read_mac_address(mac) == 0)
-			eth_setenv_enetaddr("ethaddr", mac);
-	}
-#endif
-	return 0;
-}
-#endif
-
-#if defined(CONFIG_CMD_NET) && defined(CONFIG_RESET_PHY_R)
-/* Configure and initialize PHY */
-void reset_phy(void)
-{
-	/* configure switch on egiga0 */
-	mv88e61xx_switch_initialize(&swcfg);
-}
-#endif
-
-#if defined(CONFIG_KIRKWOOD_GPIO) && defined(CONFIG_WIRELESS_SPACE_CMD)
-/* Return GPIO button status */
-static int
-do_ws(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
-{
-	if (strcmp(argv[1], "button") == 0) {
-		if (strcmp(argv[2], "rear") == 0)
-			/* invert GPIO result for intuitive while/until use */
-			return !kw_gpio_get_value(WIRELESS_SPACE_REAR_BUTTON);
-		else if (strcmp(argv[2], "front") == 0)
-			return kw_gpio_get_value(WIRELESS_SPACE_FRONT_BUTTON);
-		else
-			return -1;
-	} else {
-		return -1;
-	}
-}
-
-U_BOOT_CMD(ws, 3, 0, do_ws,
-	   "Return GPIO button status 0=off 1=on",
-	   "- ws button rear|front: test buttons' states\n"
-);
-#endif
diff --git a/configs/wireless_space_defconfig b/configs/wireless_space_defconfig
deleted file mode 100644
index 5551d27d6c..0000000000
--- a/configs/wireless_space_defconfig
+++ /dev/null
@@ -1,6 +0,0 @@
-CONFIG_ARM=y
-CONFIG_KIRKWOOD=y
-CONFIG_TARGET_WIRELESS_SPACE=y
-# CONFIG_CMD_IMLS is not set
-# CONFIG_CMD_FLASH is not set
-# CONFIG_CMD_SETEXPR is not set
diff --git a/include/configs/wireless_space.h b/include/configs/wireless_space.h
deleted file mode 100644
index 191ac1b73f..0000000000
--- a/include/configs/wireless_space.h
+++ /dev/null
@@ -1,179 +0,0 @@
-/*
- * Copyright (C) 2011 Albert ARIBAUD <albert.u.boot@aribaud.net>
- *
- * Based on the netspace_v2 code which is
- * Copyright (C) 2011 Simon Guinot <sguinot@lacie.com>
- *
- * SPDX-License-Identifier:	GPL-2.0+
- */
-
-#ifndef _CONFIG_WIRELESS_SPACE_H
-#define _CONFIG_WIRELESS_SPACE_H
-
-/*
- * Machine number definition
- */
-#define MACH_TYPE_WIRELESS_SPACE	2500 /* is missing in mach-types.h */
-#define CONFIG_MACH_TYPE		MACH_TYPE_WIRELESS_SPACE
-#define CONFIG_IDENT_STRING		" Wireless Space"
-
-/*
- * High Level Configuration Options (easy to change)
- */
-#define CONFIG_FEROCEON_88FR131		/* CPU Core subversion */
-/* SoC name */
-#define CONFIG_KW88F6281
-#define CONFIG_SKIP_LOWLEVEL_INIT	/* disable board lowlevel_init */
-
-/*
- * Commands configuration
- */
-#define CONFIG_SYS_NO_FLASH		/* no NOR or SPI flash */
-#define CONFIG_CMD_ENV
-#define CONFIG_CMD_DHCP
-#define CONFIG_CMD_PING
-#define CONFIG_CMD_NAND
-#define CONFIG_CMD_I2C
-#define CONFIG_CMD_IDE
-#define CONFIG_CMD_USB
-
-/*
- * Core clock definition
- */
-#define CONFIG_SYS_TCLK			166000000 /* 166MHz */
-
-/*
- * SDRAM configuration
- */
-#define CONFIG_NR_DRAM_BANKS		1
-
-/*
- * Different SDRAM configuration and size for some of the boards derived
- * from the Network Space v2
- */
-
-/*
- * mv-common.h should be defined after CMD configs since it used them
- * to enable certain macros
- */
-#include "mv-common.h"
-
-/* Remove or override few declarations from mv-common.h */
-#undef CONFIG_RBTREE
-#undef CONFIG_SYS_IDE_MAXBUS
-#undef CONFIG_SYS_IDE_MAXDEVICE
-#define CONFIG_SYS_IDE_MAXBUS           1
-#define CONFIG_SYS_IDE_MAXDEVICE        1
-
-/*
- * Ethernet Driver configuration
- */
-#ifdef CONFIG_CMD_NET
-#define CONFIG_MISC_INIT_R /* misc_init_r() initializes MAC address */
-#define CONFIG_MVGBE_PORTS	{1, 0}	/* enable only egiga0... */
-#define PORT_SERIAL_CONTROL_VALUE 0x00A4260E /* ... tied to the switch... */
-#define CONFIG_PHY_BASE_ADR 0xa		/* ... through a 'fake' PHY */
-#define CONFIG_MII
-#undef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
-#define CONFIG_NETCONSOLE
-#define CONFIG_MV88E61XX_SWITCH
-#define CONFIG_MV88E61XX_MULTICHIP_ADRMODE
-#define CONFIG_MV88E61XX_CMD
-#define CONFIG_CMD_TFTPPUT
-#endif /* CONFIG_CMD_NET */
-
-/*
- * SATA Driver configuration
- */
-#ifdef CONFIG_MVSATA_IDE
-#define CONFIG_SYS_ATA_IDE0_OFFSET      MV_SATA_PORT0_OFFSET
-#endif /* CONFIG_MVSATA_IDE */
-
-/*
- * Enable GPI0 support
- */
-#define CONFIG_KIRKWOOD_GPIO
-
-/*
- * Enable I2C support
- */
-#ifdef CONFIG_CMD_I2C
-/* I2C EEPROM HT24LC04 (512B - 32 pages of 16 Bytes) */
-#define CONFIG_CMD_EEPROM
-#define CONFIG_SYS_I2C_EEPROM_ADDR		0x50
-#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	4 /* 16-byte page size */
-#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1 /* 8-bit device address */
-#endif /* CONFIG_CMD_I2C */
-
-/*
- * Partition support
- */
-#define CONFIG_DOS_PARTITION
-#define CONFIG_EFI_PARTITION
-
-/*
- * File systems support
- */
-#define CONFIG_CMD_EXT2
-#define CONFIG_CMD_FAT
-
-/*
- * Use the HUSH parser
- */
-#define CONFIG_SYS_HUSH_PARSER
-
-/*
- * Console configuration
- */
-#define CONFIG_CONSOLE_MUX
-#define CONFIG_SYS_CONSOLE_IS_IN_ENV
-
-/*
- * Enable device tree support
- */
-#define CONFIG_OF_LIBFDT
-
-/*
- * Environment variables configurations
- */
-
-#define CONFIG_ENV_IS_IN_NAND
-#define CONFIG_ENV_SECT_SIZE		0x20000	/* 128KB */
-#define CONFIG_ENV_SIZE			0x20000	/* 128KB */
-#define CONFIG_ENV_OFFSET		0x80000	/* env starts here */
-
-/*
- * Board-specific command to make using buttons etc easier
- */
-
-#define CONFIG_WIRELESS_SPACE_CMD
-
-/*
- * Default environment variables
- */
-#define CONFIG_PREBOOT
-
-#define CONFIG_BOOTARGS "console=ttyS0,115200"
-
-#define CONFIG_BOOTCOMMAND					\
-	"if run usbload || run diskload; then bootm; fi"
-
-#define CONFIG_EXTRA_ENV_SETTINGS				\
-	"stdin=serial\0"					\
-	"stdout=serial\0"					\
-	"stderr=serial\0"					\
-	"bootfile=uImage\0"					\
-	"loadaddr=0x800000\0"					\
-	"autoload=no\0"						\
-	"netconsole="						\
-		"set stdin $stdin,nc; "				\
-		"set stdout $stdout,nc; "			\
-		"set stderr $stderr,nc;\0"			\
-	"diskload=ide reset && "				\
-		"ext2load ide 0:1 $loadaddr /boot/$bootfile\0"	\
-	"usbload=usb start && "					\
-		"fatload usb 0:1 $loadaddr /boot/$bootfile\0"	\
-	"preboot="						\
-		"dhcp && run netconsole\0"
-
-#endif /* _CONFIG_WIRELESS_SPACE_H */