arm: Remove support for NETARM

This stuff has been rotting in the tree for a while now. Remove it.

Signed-off-by: Marek Vasut <marex@denx.de>

17 files changed, 10 insertions, 2039 deletions

diff --git a/arch/arm/cpu/arm720t/cpu.c b/arch/arm/cpu/arm720t/cpu.c
index 864720fcdf..85c1a2c7f0 100644
--- a/arch/arm/cpu/arm720t/cpu.c
+++ b/arch/arm/cpu/arm720t/cpu.c
@@ -36,6 +36,10 @@
 #include <asm/hardware.h>
 #include <asm/system.h>
 
+#if !defined(CONFIG_INTEGRATOR) || !defined(CONFIG_ARCH_INTEGRATOR)
+#error No cleanup_before_linux() defined for this CPU type
+#endif
+
 int cleanup_before_linux (void)
 {
 	/*
@@ -46,10 +50,7 @@ int cleanup_before_linux (void)
 	 * and we set the CPU-speed to 73 MHz - see start.S for details
 	 */
 
-#if defined(CONFIG_NETARM)
-	disable_interrupts ();
-	/* Nothing more needed */
-#elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
+#if defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
 	/* No cleanup before linux for IntegratorAP/CM720T as yet */
 #elif defined(CONFIG_TEGRA)
 	/* No cleanup before linux for tegra as yet */
diff --git a/arch/arm/cpu/arm720t/interrupts.c b/arch/arm/cpu/arm720t/interrupts.c
index e3b59fef09..998efd844a 100644
--- a/arch/arm/cpu/arm720t/interrupts.c
+++ b/arch/arm/cpu/arm720t/interrupts.c
@@ -31,20 +31,11 @@
 #include <asm/proc-armv/ptrace.h>
 #include <asm/hardware.h>
 
-#ifndef CONFIG_NETARM
 /* we always count down the max. */
 #define TIMER_LOAD_VAL 0xffff
 /* macro to read the 16 bit timer */
 #define READ_TIMER (IO_TC1D & 0xffff)
 
-#else
-#define IRQEN	(*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_INTR_ENABLE))
-#define TM2CTRL (*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_TIMER2_CONTROL))
-#define TM2STAT (*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_TIMER2_STATUS))
-#define TIMER_LOAD_VAL NETARM_GEN_TSTAT_CTC_MASK
-#define READ_TIMER (TM2STAT & NETARM_GEN_TSTAT_CTC_MASK)
-#endif
-
 #ifdef CONFIG_USE_IRQ
 void do_irq (struct pt_regs *pt_regs)
 {
@@ -65,18 +56,7 @@ static ulong lastdec;
 
 int timer_init (void)
 {
-#if defined(CONFIG_NETARM)
-	/* disable all interrupts */
-	IRQEN = 0;
-
-	/* operate timer 2 in non-prescale mode */
-	TM2CTRL = ( NETARM_GEN_TIMER_SET_HZ(CONFIG_SYS_HZ) |
-		    NETARM_GEN_TCTL_ENABLE |
-		    NETARM_GEN_TCTL_INIT_COUNT(TIMER_LOAD_VAL));
-
-	/* set timer 2 counter */
-	lastdec = TIMER_LOAD_VAL;
-#elif defined(CONFIG_TEGRA)
+#if defined(CONFIG_TEGRA)
 	/* No timer routines for tegra as yet */
 	lastdec = 0;
 #else
@@ -94,66 +74,7 @@ int timer_init (void)
  */
 
 
-#if defined(CONFIG_NETARM)
-
-ulong get_timer (ulong base)
-{
-	return get_timer_masked () - base;
-}
-
-void __udelay (unsigned long usec)
-{
-	ulong tmo;
-
-	tmo = usec / 1000;
-	tmo *= CONFIG_SYS_HZ;
-	tmo /= 1000;
-
-	tmo += get_timer (0);
-
-	while (get_timer_masked () < tmo)
-}
-
-ulong get_timer_masked (void)
-{
-	ulong now = READ_TIMER;
-
-	if (lastdec >= now) {
-		/* normal mode */
-		timestamp += lastdec - now;
-	} else {
-		/* we have an overflow ... */
-		timestamp += lastdec + TIMER_LOAD_VAL - now;
-	}
-	lastdec = now;
-
-	return timestamp;
-}
-
-void udelay_masked (unsigned long usec)
-{
-	ulong tmo;
-	ulong endtime;
-	signed long diff;
-
-	if (usec >= 1000) {
-		tmo = usec / 1000;
-		tmo *= CONFIG_SYS_HZ;
-		tmo /= 1000;
-	} else {
-		tmo = usec * CONFIG_SYS_HZ;
-		tmo /= (1000*1000);
-	}
-
-	endtime = get_timer_masked () + tmo;
-
-	do {
-		ulong now = get_timer_masked ();
-		diff = endtime - now;
-	} while (diff >= 0);
-}
-
-#elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
+#if defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
 	/* No timer routines for IntegratorAP/CM720T as yet */
 #elif defined(CONFIG_TEGRA)
 	/* No timer routines for tegra as yet */
diff --git a/arch/arm/cpu/arm720t/start.S b/arch/arm/cpu/arm720t/start.S
index 3a90e0d775..45c8f0a5ea 100644
--- a/arch/arm/cpu/arm720t/start.S
+++ b/arch/arm/cpu/arm720t/start.S
@@ -284,58 +284,7 @@ _dynsym_start_ofs:
  */
 
 cpu_init_crit:
-#if defined(CONFIG_NETARM)
-	/*
-	 * prior to software reset : need to set pin PORTC4 to be *HRESET
-	 */
-	ldr	r0, =NETARM_GEN_MODULE_BASE
-	ldr	r1, =(NETARM_GEN_PORT_MODE(0x10) | \
-			NETARM_GEN_PORT_DIR(0x10))
-	str	r1, [r0, #+NETARM_GEN_PORTC]
-	/*
-	 * software reset : see HW Ref. Guide 8.2.4 : Software Service register
-	 *		    for an explanation of this process
-	 */
-	ldr	r0, =NETARM_GEN_MODULE_BASE
-	ldr	r1, =NETARM_GEN_SW_SVC_RESETA
-	str	r1, [r0, #+NETARM_GEN_SOFTWARE_SERVICE]
-	ldr	r1, =NETARM_GEN_SW_SVC_RESETB
-	str	r1, [r0, #+NETARM_GEN_SOFTWARE_SERVICE]
-	ldr	r1, =NETARM_GEN_SW_SVC_RESETA
-	str	r1, [r0, #+NETARM_GEN_SOFTWARE_SERVICE]
-	ldr	r1, =NETARM_GEN_SW_SVC_RESETB
-	str	r1, [r0, #+NETARM_GEN_SOFTWARE_SERVICE]
-	/*
-	 * setup PLL and System Config
-	 */
-	ldr	r0, =NETARM_GEN_MODULE_BASE
-
-	ldr	r1, =(	NETARM_GEN_SYS_CFG_LENDIAN | \
-			NETARM_GEN_SYS_CFG_BUSFULL | \
-			NETARM_GEN_SYS_CFG_USER_EN | \
-			NETARM_GEN_SYS_CFG_ALIGN_ABORT | \
-			NETARM_GEN_SYS_CFG_BUSARB_INT | \
-			NETARM_GEN_SYS_CFG_BUSMON_EN )
-
-	str	r1, [r0, #+NETARM_GEN_SYSTEM_CONTROL]
-
-#ifndef CONFIG_NETARM_PLL_BYPASS
-	ldr	r1, =(	NETARM_GEN_PLL_CTL_PLLCNT(NETARM_PLL_COUNT_VAL) | \
-			NETARM_GEN_PLL_CTL_POLTST_DEF | \
-			NETARM_GEN_PLL_CTL_INDIV(1) | \
-			NETARM_GEN_PLL_CTL_ICP_DEF | \
-			NETARM_GEN_PLL_CTL_OUTDIV(2) )
-	str	r1, [r0, #+NETARM_GEN_PLL_CONTROL]
-#endif
-
-	/*
-	 * mask all IRQs by clearing all bits in the INTMRs
-	 */
-	mov	r1, #0
-	ldr	r0, =NETARM_GEN_MODULE_BASE
-	str	r1, [r0, #+NETARM_GEN_INTR_ENABLE]
-
-#elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
+#if defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
 	/* No specific initialisation for IntegratorAP/CM720T as yet */
 #elif defined(CONFIG_TEGRA)
 	/* No cpu_init_crit for tegra as yet */
@@ -533,27 +482,7 @@ fiq:
 #endif
 #endif /* CONFIG_SPL_BUILD */
 
-#if defined(CONFIG_NETARM)
-	.align	5
-.globl reset_cpu
-reset_cpu:
-	ldr	r1, =NETARM_MEM_MODULE_BASE
-	ldr	r0, [r1, #+NETARM_MEM_CS0_BASE_ADDR]
-	ldr	r1, =0xFFFFF000
-	and	r0, r1, r0
-	ldr	r1, =(relocate-CONFIG_SYS_TEXT_BASE)
-	add	r0, r1, r0
-	ldr	r4, =NETARM_GEN_MODULE_BASE
-	ldr	r1, =NETARM_GEN_SW_SVC_RESETA
-	str	r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE]
-	ldr	r1, =NETARM_GEN_SW_SVC_RESETB
-	str	r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE]
-	ldr	r1, =NETARM_GEN_SW_SVC_RESETA
-	str	r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE]
-	ldr	r1, =NETARM_GEN_SW_SVC_RESETB
-	str	r1, [r4, #+NETARM_GEN_SOFTWARE_SERVICE]
-	mov	pc, r0
-#elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
+#if defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
 	/* No specific reset actions for IntegratorAP/CM720T as yet */
 #elif defined(CONFIG_TEGRA)
 	/* No specific reset actions for tegra as yet */
diff --git a/arch/arm/include/asm/arch-arm720t/hardware.h b/arch/arm/include/asm/arch-arm720t/hardware.h
index 0a357b1e0a..0a766108a6 100644
--- a/arch/arm/include/asm/arch-arm720t/hardware.h
+++ b/arch/arm/include/asm/arch-arm720t/hardware.h
@@ -24,9 +24,7 @@
  * MA 02111-1307 USA
  */
 
-#if defined(CONFIG_NETARM)
-#include <asm/arch-arm720t/netarm_registers.h>
-#elif defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
+#if defined(CONFIG_INTEGRATOR) && defined(CONFIG_ARCH_INTEGRATOR)
 /* include IntegratorCP/CM720T specific hardware file if there was one */
 #else
 #error No hardware file defined for this configuration
diff --git a/arch/arm/include/asm/arch-arm720t/netarm_dma_module.h b/arch/arm/include/asm/arch-arm720t/netarm_dma_module.h
deleted file mode 100644
index 328eaf0da9..0000000000
--- a/arch/arm/include/asm/arch-arm720t/netarm_dma_module.h
+++ /dev/null
@@ -1,182 +0,0 @@
-/* * include/asm-armnommu/arch-netarm/netarm_dma_module.h
- *
- * Copyright (C) 2000 NETsilicon, Inc.
- * Copyright (C) 2000 WireSpeed Communications Corporation
- *
- * This software is copyrighted by WireSpeed. LICENSEE agrees that
- * it will not delete this copyright notice, trademarks or protective
- * notices from any copy made by LICENSEE.
- *
- * This software is provided "AS-IS" and any express or implied
- * warranties or conditions, including but not limited to any
- * implied warranties of merchantability and fitness for a particular
- * purpose regarding this software. In no event shall WireSpeed
- * be liable for any indirect, consequential, or incidental damages,
- * loss of profits or revenue, loss of use or data, or interruption
- * of business, whether the alleged damages are labeled in contract,
- * tort, or indemnity.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * author(s) : Joe deBlaquiere
- *             David Smith
- */
-
-#ifndef __NETARM_DMA_MODULE_REGISTERS_H
-#define __NETARM_DMA_MODULE_REGISTERS_H
-
-/* GEN unit register offsets */
-
-#define	NETARM_DMA_MODULE_BASE		(0xFF900000)
-
-#define get_dma_reg_addr(c) ((volatile unsigned int *)(NETARM_DMA_MODULE_BASE + (c)))
-
-#define	NETARM_DMA1A_BFR_DESCRPTOR_PTR	(0x00)
-#define	NETARM_DMA1A_CONTROL		(0x10)
-#define	NETARM_DMA1A_STATUS		(0x14)
-#define	NETARM_DMA1B_BFR_DESCRPTOR_PTR	(0x20)
-#define	NETARM_DMA1B_CONTROL		(0x30)
-#define	NETARM_DMA1B_STATUS		(0x34)
-#define	NETARM_DMA1C_BFR_DESCRPTOR_PTR	(0x40)
-#define	NETARM_DMA1C_CONTROL		(0x50)
-#define	NETARM_DMA1C_STATUS		(0x54)
-#define	NETARM_DMA1D_BFR_DESCRPTOR_PTR	(0x60)
-#define	NETARM_DMA1D_CONTROL		(0x70)
-#define	NETARM_DMA1D_STATUS		(0x74)
-
-#define	NETARM_DMA2_BFR_DESCRPTOR_PTR	(0x80)
-#define	NETARM_DMA2_CONTROL		(0x90)
-#define	NETARM_DMA2_STATUS		(0x94)
-
-#define	NETARM_DMA3_BFR_DESCRPTOR_PTR	(0xA0)
-#define	NETARM_DMA3_CONTROL		(0xB0)
-#define	NETARM_DMA3_STATUS		(0xB4)
-
-#define	NETARM_DMA4_BFR_DESCRPTOR_PTR	(0xC0)
-#define	NETARM_DMA4_CONTROL		(0xD0)
-#define	NETARM_DMA4_STATUS		(0xD4)
-
-#define	NETARM_DMA5_BFR_DESCRPTOR_PTR	(0xE0)
-#define	NETARM_DMA5_CONTROL		(0xF0)
-#define	NETARM_DMA5_STATUS		(0xF4)
-
-#define	NETARM_DMA6_BFR_DESCRPTOR_PTR	(0x100)
-#define	NETARM_DMA6_CONTROL		(0x110)
-#define	NETARM_DMA6_STATUS		(0x114)
-
-#define	NETARM_DMA7_BFR_DESCRPTOR_PTR	(0x120)
-#define	NETARM_DMA7_CONTROL		(0x130)
-#define	NETARM_DMA7_STATUS		(0x134)
-
-#define	NETARM_DMA8_BFR_DESCRPTOR_PTR	(0x140)
-#define	NETARM_DMA8_CONTROL		(0x150)
-#define	NETARM_DMA8_STATUS		(0x154)
-
-#define	NETARM_DMA9_BFR_DESCRPTOR_PTR	(0x160)
-#define	NETARM_DMA9_CONTROL		(0x170)
-#define	NETARM_DMA9_STATUS		(0x174)
-
-#define	NETARM_DMA10_BFR_DESCRPTOR_PTR	(0x180)
-#define	NETARM_DMA10_CONTROL		(0x190)
-#define	NETARM_DMA10_STATUS		(0x194)
-
-/* select bitfield defintions */
-
-/* DMA Control Register ( 0xFF90_0XX0 ) */
-
-#define NETARM_DMA_CTL_ENABLE		(0x80000000)
-
-#define NETARM_DMA_CTL_ABORT		(0x40000000)
-
-#define NETARM_DMA_CTL_BUS_100_PERCENT	(0x00000000)
-#define NETARM_DMA_CTL_BUS_75_PERCENT	(0x10000000)
-#define NETARM_DMA_CTL_BUS_50_PERCENT	(0x20000000)
-#define NETARM_DMA_CTL_BUS_25_PERCENT	(0x30000000)
-
-#define NETARM_DMA_CTL_BUS_MASK		(0x30000000)
-
-#define NETARM_DMA_CTL_MODE_FB_TO_MEM	(0x00000000)
-#define NETARM_DMA_CTL_MODE_FB_FROM_MEM	(0x04000000)
-#define NETARM_DMA_CTL_MODE_MEM_TO_MEM	(0x08000000)
-
-#define NETARM_DMA_CTL_BURST_NONE	(0x00000000)
-#define NETARM_DMA_CTL_BURST_8_BYTE	(0x01000000)
-#define NETARM_DMA_CTL_BURST_16_BYTE	(0x02000000)
-
-#define NETARM_DMA_CTL_BURST_MASK	(0x03000000)
-
-#define NETARM_DMA_CTL_SRC_INCREMENT	(0x00200000)
-
-#define NETARM_DMA_CTL_DST_INCREMENT	(0x00100000)
-
-/* these apply only to ext xfers on DMA 3 or 4 */
-
-#define NETARM_DMA_CTL_CH_3_4_REQ_EXT	(0x00800000)
-
-#define NETARM_DMA_CTL_CH_3_4_DATA_32	(0x00000000)
-#define NETARM_DMA_CTL_CH_3_4_DATA_16	(0x00010000)
-#define NETARM_DMA_CTL_CH_3_4_DATA_8	(0x00020000)
-
-#define NETARM_DMA_CTL_STATE(X)	((X) & 0xFC00)
-#define NETARM_DMA_CTL_INDEX(X)	((X) & 0x03FF)
-
-/* DMA Status Register ( 0xFF90_0XX4 ) */
-
-#define NETARM_DMA_STAT_NC_INTPEN	(0x80000000)
-#define NETARM_DMA_STAT_EC_INTPEN	(0x40000000)
-#define NETARM_DMA_STAT_NR_INTPEN	(0x20000000)
-#define NETARM_DMA_STAT_CA_INTPEN	(0x10000000)
-#define NETARM_DMA_STAT_INTPEN_MASK	(0xF0000000)
-
-#define NETARM_DMA_STAT_NC_INT_EN	(0x00800000)
-#define NETARM_DMA_STAT_EC_INT_EN	(0x00400000)
-#define NETARM_DMA_STAT_NR_INT_EN	(0x00200000)
-#define NETARM_DMA_STAT_CA_INT_EN	(0x00100000)
-#define NETARM_DMA_STAT_INT_EN_MASK	(0x00F00000)
-
-#define NETARM_DMA_STAT_WRAP		(0x00080000)
-#define NETARM_DMA_STAT_IDONE		(0x00040000)
-#define NETARM_DMA_STAT_LAST		(0x00020000)
-#define NETARM_DMA_STAT_FULL		(0x00010000)
-
-#define	NETARM_DMA_STAT_BUFLEN(X)	((X) & 0x7FFF)
-
-/* DMA Buffer Descriptor Word 0 bitfields. */
-
-#define NETARM_DMA_BD0_WRAP		(0x80000000)
-#define NETARM_DMA_BD0_IDONE		(0x40000000)
-#define NETARM_DMA_BD0_LAST		(0x20000000)
-#define NETARM_DMA_BD0_BUFPTR_MASK	(0x1FFFFFFF)
-
-/* DMA Buffer Descriptor Word 1 bitfields. */
-
-#define NETARM_DMA_BD1_STATUS_MASK	(0xFFFF0000)
-#define NETARM_DMA_BD1_FULL		(0x00008000)
-#define NETARM_DMA_BD1_BUFLEN_MASK	(0x00007FFF)
-
-#ifndef	__ASSEMBLER__
-
-typedef	struct __NETARM_DMA_Buff_Desc_FlyBy
-{
-	unsigned int word0;
-	unsigned int word1;
-} NETARM_DMA_Buff_Desc_FlyBy, *pNETARM_DMA_Buff_Desc_FlyBy ;
-
-typedef	struct __NETARM_DMA_Buff_Desc_M_to_M
-{
-	unsigned int word0;
-	unsigned int word1;
-	unsigned int word2;
-	unsigned int word3;
-} NETARM_DMA_Buff_Desc_M_to_M, *pNETARM_DMA_Buff_Desc_M_to_M ;
-
-#endif
-
-#endif
diff --git a/arch/arm/include/asm/arch-arm720t/netarm_eni_module.h b/arch/arm/include/asm/arch-arm720t/netarm_eni_module.h
deleted file mode 100644
index 317b354513..0000000000
--- a/arch/arm/include/asm/arch-arm720t/netarm_eni_module.h
+++ /dev/null
@@ -1,121 +0,0 @@
-/*
- * include/asm-armnommu/arch-netarm/netarm_eni_module.h
- *
- * Copyright (C) 2000 NETsilicon, Inc.
- * Copyright (C) 2000 WireSpeed Communications Corporation
- *
- * This software is copyrighted by WireSpeed. LICENSEE agrees that
- * it will not delete this copyright notice, trademarks or protective
- * notices from any copy made by LICENSEE.
- *
- * This software is provided "AS-IS" and any express or implied
- * warranties or conditions, including but not limited to any
- * implied warranties of merchantability and fitness for a particular
- * purpose regarding this software. In no event shall WireSpeed
- * be liable for any indirect, consequential, or incidental damages,
- * loss of profits or revenue, loss of use or data, or interruption
- * of business, whether the alleged damages are labeled in contract,
- * tort, or indemnity.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * author(s) : David Smith
- */
-
-#ifndef __NETARM_ENI_MODULE_REGISTERS_H
-#define __NETARM_ENI_MODULE_REGISTERS_H
-
-/* ENI unit register offsets */
-
-/* #ifdef CONFIG_ARCH_NETARM */
-#define	NETARM_ENI_MODULE_BASE		(0xFFA00000)
-/* #endif / * CONFIG_ARCH_NETARM */
-
-#define get_eni_reg_addr(c) ((volatile unsigned int *)(NETARM_ENI_MODULE_BASE + (c)))
-#define get_eni_ctl_reg_addr(minor) \
-	(get_eni_reg_addr(NETARM_ENI_1284_PORT1_CONTROL) + (minor))
-
-#define	NETARM_ENI_GENERAL_CONTROL	(0x00)
-#define	NETARM_ENI_STATUS_CONTROL	(0x04)
-#define	NETARM_ENI_FIFO_MODE_DATA	(0x08)
-
-#define	NETARM_ENI_1284_PORT1_CONTROL	(0x10)
-#define	NETARM_ENI_1284_PORT2_CONTROL	(0x14)
-#define	NETARM_ENI_1284_PORT3_CONTROL	(0x18)
-#define	NETARM_ENI_1284_PORT4_CONTROL	(0x1c)
-
-#define	NETARM_ENI_1284_CHANNEL1_DATA	(0x20)
-#define	NETARM_ENI_1284_CHANNEL2_DATA	(0x24)
-#define	NETARM_ENI_1284_CHANNEL3_DATA	(0x28)
-#define	NETARM_ENI_1284_CHANNEL4_DATA	(0x2c)
-
-#define	NETARM_ENI_ENI_CONTROL		(0x30)
-#define	NETARM_ENI_ENI_PULSED_INTR	(0x34)
-#define	NETARM_ENI_ENI_SHARED_RAM_ADDR	(0x38)
-#define	NETARM_ENI_ENI_SHARED		(0x3c)
-
-/* select bitfield defintions */
-
-/* General Control Register (0xFFA0_0000) */
-
-#define NETARM_ENI_GCR_ENIMODE_IEEE1284	(0x00000001)
-#define NETARM_ENI_GCR_ENIMODE_SHRAM16	(0x00000004)
-#define NETARM_ENI_GCR_ENIMODE_SHRAM8	(0x00000005)
-#define NETARM_ENI_GCR_ENIMODE_FIFO16	(0x00000006)
-#define NETARM_ENI_GCR_ENIMODE_FIFO8	(0x00000007)
-
-#define NETARM_ENI_GCR_ENIMODE_MASK	(0x00000007)
-
-/* IEEE 1284 Port Control Registers 1-4 (0xFFA0_0010, 0xFFA0_0014,
-   0xFFA0_0018, 0xFFA0_001c) */
-
-#define NETARM_ENI_1284PC_PORT_ENABLE	(0x80000000)
-#define NETARM_ENI_1284PC_DMA_ENABLE	(0x40000000)
-#define NETARM_ENI_1284PC_OBE_INT_EN	(0x20000000)
-#define NETARM_ENI_1284PC_ACK_INT_EN	(0x10000000)
-#define NETARM_ENI_1284PC_ECP_MODE	(0x08000000)
-#define NETARM_ENI_1284PC_LOOPBACK_MODE	(0x04000000)
-
-#define NETARM_ENI_1284PC_STROBE_TIME0	(0x00000000) /* 0.5 uS */
-#define NETARM_ENI_1284PC_STROBE_TIME1	(0x01000000) /* 1.0 uS */
-#define NETARM_ENI_1284PC_STROBE_TIME2	(0x02000000) /* 5.0 uS */
-#define NETARM_ENI_1284PC_STROBE_TIME3	(0x03000000) /* 10.0 uS */
-#define NETARM_ENI_1284PC_STROBE_MASK	(0x03000000)
-
-#define NETARM_ENI_1284PC_MAN_STROBE_EN	(0x00800000)
-#define NETARM_ENI_1284PC_FAST_MODE	(0x00400000)
-#define NETARM_ENI_1284PC_BIDIR_MODE	(0x00200000)
-
-#define NETARM_ENI_1284PC_MAN_STROBE	(0x00080000)
-#define NETARM_ENI_1284PC_AUTO_FEED	(0x00040000)
-#define NETARM_ENI_1284PC_INIT		(0x00020000)
-#define NETARM_ENI_1284PC_HSELECT	(0x00010000)
-#define NETARM_ENI_1284PC_FE_INT_EN	(0x00008000)
-#define NETARM_ENI_1284PC_EPP_MODE	(0x00004000)
-#define NETARM_ENI_1284PC_IBR_INT_EN	(0x00002000)
-#define NETARM_ENI_1284PC_IBR		(0x00001000)
-
-#define NETARM_ENI_1284PC_RXFDB_1BYTE	(0x00000400)
-#define NETARM_ENI_1284PC_RXFDB_2BYTE	(0x00000800)
-#define NETARM_ENI_1284PC_RXFDB_3BYTE	(0x00000c00)
-#define NETARM_ENI_1284PC_RXFDB_4BYTE	(0x00000000)
-
-#define NETARM_ENI_1284PC_RBCC		(0x00000200)
-#define NETARM_ENI_1284PC_RBCT		(0x00000100)
-#define NETARM_ENI_1284PC_ACK		(0x00000080)
-#define NETARM_ENI_1284PC_FIFO_E	(0x00000040)
-#define NETARM_ENI_1284PC_OBE		(0x00000020)
-#define NETARM_ENI_1284PC_ACK_INT	(0x00000010)
-#define NETARM_ENI_1284PC_BUSY		(0x00000008)
-#define NETARM_ENI_1284PC_PE		(0x00000004)
-#define NETARM_ENI_1284PC_PSELECT	(0x00000002)
-#define NETARM_ENI_1284PC_FAULT		(0x00000001)
-
-#endif /* __NETARM_ENI_MODULE_REGISTERS_H */
diff --git a/arch/arm/include/asm/arch-arm720t/netarm_eth_module.h b/arch/arm/include/asm/arch-arm720t/netarm_eth_module.h
deleted file mode 100644
index 8f2f36981a..0000000000
--- a/arch/arm/include/asm/arch-arm720t/netarm_eth_module.h
+++ /dev/null
@@ -1,160 +0,0 @@
-/*
- * include/asm-armnommu/arch-netarm/netarm_eth_module.h
- *
- * Copyright (C) 2000 NETsilicon, Inc.
- * Copyright (C) 2000 WireSpeed Communications Corporation
- *
- * This software is copyrighted by WireSpeed. LICENSEE agrees that
- * it will not delete this copyright notice, trademarks or protective
- * notices from any copy made by LICENSEE.
- *
- * This software is provided "AS-IS" and any express or implied
- * warranties or conditions, including but not limited to any
- * implied warranties of merchantability and fitness for a particular
- * purpose regarding this software. In no event shall WireSpeed
- * be liable for any indirect, consequential, or incidental damages,
- * loss of profits or revenue, loss of use or data, or interruption
- * of business, whether the alleged damages are labeled in contract,
- * tort, or indemnity.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * author(s) : Jackie Smith Cashion
- *             David Smith
- */
-
-#ifndef __NETARM_ETH_MODULE_REGISTERS_H
-#define __NETARM_ETH_MODULE_REGISTERS_H
-
-/* ETH unit register offsets */
-
-#define	NETARM_ETH_MODULE_BASE		(0xFF800000)
-
-#define get_eth_reg_addr(c) ((volatile unsigned int *)(NETARM_ETH_MODULE_BASE + (c)))
-
-#define NETARM_ETH_GEN_CTRL		(0x000) /* Ethernet Gen Control Reg */
-#define NETARM_ETH_GEN_STAT		(0x004) /* Ethernet Gen Status Reg */
-#define NETARM_ETH_FIFO_DAT1            (0x008) /* Fifo Data Reg 1 */
-#define NETARM_ETH_FIFO_DAT2            (0x00C) /* Fifo Data Reg 2 */
-#define NETARM_ETH_TX_STAT              (0x010) /* Transmit Status Reg */
-#define NETARM_ETH_RX_STAT              (0x014) /* Receive Status Reg */
-
-#define NETARM_ETH_MAC_CFG		(0x400) /* MAC Configuration Reg */
-#define NETARM_ETH_PCS_CFG		(0x408) /* PCS Configuration Reg */
-#define NETARM_ETH_STL_CFG		(0x410) /* STL Configuration Reg */
-#define NETARM_ETH_B2B_IPG_GAP_TMR	(0x440) /* Back-to-back IPG
-						   Gap Timer Reg */
-#define NETARM_ETH_NB2B_IPG_GAP_TMR	(0x444) /* Non Back-to-back
-						   IPG Gap Timer Reg */
-#define NETARM_ETH_MII_CMD		(0x540) /* MII (PHY) Command Reg */
-#define NETARM_ETH_MII_ADDR		(0x544) /* MII Address Reg */
-#define NETARM_ETH_MII_WRITE		(0x548) /* MII Write Data Reg */
-#define NETARM_ETH_MII_READ		(0x54C) /* MII Read Data Reg */
-#define NETARM_ETH_MII_IND		(0x550) /* MII Indicators Reg */
-#define NETARM_ETH_MIB_CRCEC		(0x580) /* (MIB) CRC Error Counter */
-#define NETARM_ETH_MIB_AEC		(0x584) /* Alignment Error Counter */
-#define NETARM_ETH_MIB_CEC		(0x588) /* Code Error Counter */
-#define NETARM_ETH_MIB_LFC		(0x58C) /* Long Frame Counter */
-#define NETARM_ETH_MIB_SFC		(0x590) /* Short Frame Counter */
-#define NETARM_ETH_MIB_LCC		(0x594) /* Late Collision Counter */
-#define NETARM_ETH_MIB_EDC		(0x598) /* Excessive Deferral
-						   Counter */
-#define NETARM_ETH_MIB_MCC		(0x59C) /* Maximum Collision Counter */
-#define NETARM_ETH_SAL_FILTER		(0x5C0) /* SAL Station Address
-						   Filter Reg */
-#define NETARM_ETH_SAL_STATION_ADDR_1	(0x5C4) /* SAL Station Address
-						   Reg */
-#define NETARM_ETH_SAL_STATION_ADDR_2	(0x5C8)
-#define NETARM_ETH_SAL_STATION_ADDR_3	(0x5CC)
-#define NETARM_ETH_SAL_HASH_TBL_1	(0x5D0) /* SAL Multicast Hash Table*/
-#define NETARM_ETH_SAL_HASH_TBL_2	(0x5D4)
-#define NETARM_ETH_SAL_HASH_TBL_3	(0x5D8)
-#define NETARM_ETH_SAL_HASH_TBL_4	(0x5DC)
-
-/* select bitfield defintions */
-
-/* Ethernet General Control Register (0xFF80_0000) */
-
-#define NETARM_ETH_GCR_ERX		(0x80000000) /* Enable Receive FIFO */
-#define NETARM_ETH_GCR_ERXDMA		(0x40000000) /* Enable Receive DMA */
-#define NETARM_ETH_GCR_ETX		(0x00800000) /* Enable Transmit FIFO */
-#define NETARM_ETH_GCR_ETXDMA		(0x00400000) /* Enable Transmit DMA */
-#define NETARM_ETH_GCR_ETXWM_50		(0x00100000) /* Transmit FIFO Water
-							Mark.  Start transmit
-							when FIFO is 50%
-							full. */
-#define NETARM_ETH_GCR_PNA		(0x00000400) /* pSOS pNA Buffer
-							Descriptor Format */
-
-/* Ethernet General Status Register (0xFF80_0004) */
-
-#define NETARM_ETH_GST_RXFDB            (0x30000000)
-#define NETARM_ETH_GST_RXREGR		(0x08000000) /* Receive Register
-							Ready */
-#define NETARM_ETH_GST_RXFIFOH		(0x04000000)
-#define NETARM_ETH_GST_RXBR		(0x02000000)
-#define NETARM_ETH_GST_RXSKIP		(0x01000000)
-
-#define NETARM_ETH_GST_TXBC             (0x00020000)
-
-
-/* Ethernet Transmit Status Register (0xFF80_0010) */
-
-#define NETARM_ETH_TXSTAT_TXOK          (0x00008000)
-
-
-/* Ethernet Receive Status Register (0xFF80_0014) */
-
-#define NETARM_ETH_RXSTAT_SIZE          (0xFFFF0000)
-#define NETARM_ETH_RXSTAT_RXOK          (0x00002000)
-
-
-/* PCS Configuration Register (0xFF80_0408) */
-
-#define NETARM_ETH_PCSC_NOCFR		(0x1) /* Disable Ciphering */
-#define NETARM_ETH_PCSC_ENJAB		(0x2) /* Enable Jabber Protection */
-#define NETARM_ETH_PCSC_CLKS_25M	(0x0) /* 25 MHz Clock Speed Select */
-#define NETARM_ETH_PCSC_CLKS_33M	(0x4) /* 33 MHz Clock Speed Select */
-
-/* STL Configuration Register (0xFF80_0410) */
-
-#define NETARM_ETH_STLC_RXEN		(0x2) /* Enable Packet Receiver */
-#define NETARM_ETH_STLC_AUTOZ		(0x4) /* Auto Zero Statistics */
-
-/* MAC Configuration Register (0xFF80_0400) */
-
-#define NETARM_ETH_MACC_HUGEN		(0x1) /* Enable Unlimited Transmit
-						 Frame Sizes */
-#define NETARM_ETH_MACC_PADEN		(0x4) /* Automatic Pad Fill Frames
-						 to 64 Bytes */
-#define NETARM_ETH_MACC_CRCEN		(0x8) /* Append CRC to Transmit
-						 Frames */
-
-/* MII (PHY) Command Register (0xFF80_0540) */
-
-#define NETARM_ETH_MIIC_RSTAT		(0x1) /* Single Scan for Read Data */
-
-/* MII Indicators Register (0xFF80_0550) */
-
-#define NETARM_ETH_MIII_BUSY		(0x1) /* MII I/F Busy with
-						 Read/Write */
-
-/* SAL Station Address Filter Register (0xFF80_05C0) */
-
-#define NETARM_ETH_SALF_PRO		(0x8) /* Enable Promiscuous Mode */
-#define NETARM_ETH_SALF_PRM		(0x4) /* Accept All Multicast
-						 Packets */
-#define NETARM_ETH_SALF_PRA		(0x2) /* Accept Mulitcast Packets
-						 using Hash Table */
-#define NETARM_ETH_SALF_BROAD		(0x1) /* Accept All Broadcast
-						 Packets */
-
-
-#endif /* __NETARM_GEN_MODULE_REGISTERS_H */
diff --git a/arch/arm/include/asm/arch-arm720t/netarm_gen_module.h b/arch/arm/include/asm/arch-arm720t/netarm_gen_module.h
deleted file mode 100644
index 13656a3ad2..0000000000
--- a/arch/arm/include/asm/arch-arm720t/netarm_gen_module.h
+++ /dev/null
@@ -1,186 +0,0 @@
-/*
- * include/asm-armnommu/arch-netarm/netarm_gen_module.h
- *
- * Copyright (C) 2005
- * Art Shipkowski, Videon Central, Inc., <art@videon-central.com>
- *
- * Copyright (C) 2000, 2001 NETsilicon, Inc.
- * Copyright (C) 2000, 2001 Red Hat, Inc.
- *
- * This software is copyrighted by Red Hat. LICENSEE agrees that
- * it will not delete this copyright notice, trademarks or protective
- * notices from any copy made by LICENSEE.
- *
- * This software is provided "AS-IS" and any express or implied
- * warranties or conditions, including but not limited to any
- * implied warranties of merchantability and fitness for a particular
- * purpose regarding this software. In no event shall Red Hat
- * be liable for any indirect, consequential, or incidental damages,
- * loss of profits or revenue, loss of use or data, or interruption
- * of business, whether the alleged damages are labeled in contract,
- * tort, or indemnity.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * author(s) : Joe deBlaquiere
- *
- * Modified to support NS7520 by Art Shipkowski.
- */
-
-#ifndef __NETARM_GEN_MODULE_REGISTERS_H
-#define __NETARM_GEN_MODULE_REGISTERS_H
-
-/* GEN unit register offsets */
-
-#define NETARM_GEN_MODULE_BASE		(0xFFB00000)
-
-#define get_gen_reg_addr(c) ((volatile unsigned int *)(NETARM_GEN_MODULE_BASE + (c)))
-
-#define NETARM_GEN_SYSTEM_CONTROL	(0x00)
-#define NETARM_GEN_STATUS_CONTROL	(0x04)
-#define NETARM_GEN_PLL_CONTROL		(0x08)
-#define NETARM_GEN_SOFTWARE_SERVICE	(0x0c)
-
-#define NETARM_GEN_TIMER1_CONTROL	(0x10)
-#define NETARM_GEN_TIMER1_STATUS	(0x14)
-#define NETARM_GEN_TIMER2_CONTROL	(0x18)
-#define NETARM_GEN_TIMER2_STATUS	(0x1c)
-
-#define NETARM_GEN_PORTA		(0x20)
-#ifndef CONFIG_NETARM_NS7520
-#define NETARM_GEN_PORTB		(0x24)
-#endif
-#define NETARM_GEN_PORTC		(0x28)
-
-#define NETARM_GEN_INTR_ENABLE		(0x30)
-#define NETARM_GEN_INTR_ENABLE_SET	(0x34)
-#define NETARM_GEN_INTR_ENABLE_CLR	(0x38)
-#define NETARM_GEN_INTR_STATUS_EN	(0x34)
-#define NETARM_GEN_INTR_STATUS_RAW	(0x38)
-
-#define NETARM_GEN_CACHE_CONTROL1	(0x40)
-#define NETARM_GEN_CACHE_CONTROL2	(0x44)
-
-/* select bitfield definitions */
-
-/* System Control Register ( 0xFFB0_0000 ) */
-
-#define NETARM_GEN_SYS_CFG_LENDIAN	(0x80000000)
-#define NETARM_GEN_SYS_CFG_BENDIAN	(0x00000000)
-
-#define NETARM_GEN_SYS_CFG_BUSQRTR	(0x00000000)
-#define NETARM_GEN_SYS_CFG_BUSHALF	(0x20000000)
-#define NETARM_GEN_SYS_CFG_BUSFULL	(0x40000000)
-
-#define NETARM_GEN_SYS_CFG_BCLK_DISABLE (0x10000000)
-
-#define NETARM_GEN_SYS_CFG_WDOG_EN	(0x01000000)
-#define NETARM_GEN_SYS_CFG_WDOG_IRQ	(0x00000000)
-#define NETARM_GEN_SYS_CFG_WDOG_FIQ	(0x00400000)
-#define NETARM_GEN_SYS_CFG_WDOG_RST	(0x00800000)
-#define NETARM_GEN_SYS_CFG_WDOG_24	(0x00000000)
-#define NETARM_GEN_SYS_CFG_WDOG_26	(0x00100000)
-#define NETARM_GEN_SYS_CFG_WDOG_28	(0x00200000)
-#define NETARM_GEN_SYS_CFG_WDOG_29	(0x00300000)
-
-#define NETARM_GEN_SYS_CFG_BUSMON_EN	(0x00040000)
-#define NETARM_GEN_SYS_CFG_BUSMON_128	(0x00000000)
-#define NETARM_GEN_SYS_CFG_BUSMON_64	(0x00010000)
-#define NETARM_GEN_SYS_CFG_BUSMON_32	(0x00020000)
-#define NETARM_GEN_SYS_CFG_BUSMON_16	(0x00030000)
-
-#define NETARM_GEN_SYS_CFG_USER_EN	(0x00008000)
-#define NETARM_GEN_SYS_CFG_BUSER_EN	(0x00004000)
-
-#define NETARM_GEN_SYS_CFG_BUSARB_INT	(0x00002000)
-#define NETARM_GEN_SYS_CFG_BUSARB_EXT	(0x00000000)
-
-#define NETARM_GEN_SYS_CFG_DMATST	(0x00001000)
-
-#define NETARM_GEN_SYS_CFG_TEALAST	(0x00000800)
-
-#define NETARM_GEN_SYS_CFG_ALIGN_ABORT	(0x00000400)
-
-#define NETARM_GEN_SYS_CFG_CACHE_EN	(0x00000200)
-
-#define NETARM_GEN_SYS_CFG_WRI_BUF_EN	(0x00000100)
-
-#define NETARM_GEN_SYS_CFG_CACHE_INIT	(0x00000080)
-
-/* PLL Control Register ( 0xFFB0_0008 ) */
-
-#define NETARM_GEN_PLL_CTL_PLLCNT_MASK	(0x0F000000)
-
-#define NETARM_GEN_PLL_CTL_PLLCNT(x)	(((x)<<24) & \
-					 NETARM_GEN_PLL_CTL_PLLCNT_MASK)
-
-/* Defaults for POLTST and ICP Fields in PLL CTL */
-#define NETARM_GEN_PLL_CTL_OUTDIV(x)	(x)
-#define NETARM_GEN_PLL_CTL_INDIV(x)	((x)<<6)
-#define NETARM_GEN_PLL_CTL_POLTST_DEF	(0x00000E00)
-#define NETARM_GEN_PLL_CTL_ICP_DEF	(0x0000003C)
-
-
-/* Software Service Register ( 0xFFB0_000C ) */
-
-#define NETARM_GEN_SW_SVC_RESETA	(0x123)
-#define NETARM_GEN_SW_SVC_RESETB	(0x321)
-
-/* PORT C Register ( 0xFFB0_0028 ) */
-
-#ifndef CONFIG_NETARM_NS7520
-#define NETARM_GEN_PORT_MODE(x)		(((x)<<24) + (0xFF00))
-#define NETARM_GEN_PORT_DIR(x)		(((x)<<16) + (0xFF00))
-#else
-#define NETARM_GEN_PORT_MODE(x)		((x)<<24)
-#define NETARM_GEN_PORT_DIR(x)		((x)<<16)
-#define NETARM_GEN_PORT_CSF(x)		((x)<<8)
-#endif
-
-/* Timer Registers ( 0xFFB0_0010 0xFFB0_0018 ) */
-
-#define NETARM_GEN_TCTL_ENABLE		(0x80000000)
-#define NETARM_GEN_TCTL_INT_ENABLE	(0x40000000)
-
-#define NETARM_GEN_TCTL_USE_IRQ		(0x00000000)
-#define NETARM_GEN_TCTL_USE_FIQ		(0x20000000)
-
-#define NETARM_GEN_TCTL_USE_PRESCALE	(0x10000000)
-#define NETARM_GEN_TCTL_INIT_COUNT(x)	((x) & 0x1FF)
-
-#define NETARM_GEN_TSTAT_INTPEN		(0x40000000)
-#if ~defined(CONFIG_NETARM_NS7520)
-#define NETARM_GEN_TSTAT_CTC_MASK	(0x000001FF)
-#else
-#define NETARM_GEN_TSTAT_CTC_MASK	(0x0FFFFFFF)
-#endif
-
-/* prescale to msecs conversion */
-
-#if !defined(CONFIG_NETARM_PLL_BYPASS)
-#define NETARM_GEN_TIMER_MSEC_P(x)	( ( ( 20480 ) * ( 0x1FF - ( (x) &	    \
-					    NETARM_GEN_TSTAT_CTC_MASK ) +   \
-					    1 ) ) / (NETARM_XTAL_FREQ/1000) )
-
-#define NETARM_GEN_TIMER_SET_HZ(x)	( ( ((NETARM_XTAL_FREQ/(20480*(x)))-1) & \
-					  NETARM_GEN_TSTAT_CTC_MASK ) | \
-					  NETARM_GEN_TCTL_USE_PRESCALE )
-
-#else
-#define NETARM_GEN_TIMER_MSEC_P(x)	( ( ( 4096 ) * ( 0x1FF - ( (x) &    \
-					    NETARM_GEN_TSTAT_CTC_MASK ) +   \
-					    1 ) ) / (NETARM_XTAL_FREQ/1000) )
-
-#define NETARM_GEN_TIMER_SET_HZ(x)	( ( ((NETARM_XTAL_FREQ/(4096*(x)))-1) & \
-					  NETARM_GEN_TSTAT_CTC_MASK ) | \
-					  NETARM_GEN_TCTL_USE_PRESCALE )
-#endif
-
-#endif
diff --git a/arch/arm/include/asm/arch-arm720t/netarm_mem_module.h b/arch/arm/include/asm/arch-arm720t/netarm_mem_module.h
deleted file mode 100644
index c650c3b004..0000000000
--- a/arch/arm/include/asm/arch-arm720t/netarm_mem_module.h
+++ /dev/null
@@ -1,184 +0,0 @@
-/*
- * include/asm-armnommu/arch-netarm/netarm_mem_module.h
- *
- * Copyright (C) 2005
- * Art Shipkowski, Videon Central, Inc., <art@videon-central.com>
- *
- * Copyright (C) 2000, 2001 NETsilicon, Inc.
- * Copyright (C) 2000, 2001 Red Hat, Inc.
- *
- * This software is copyrighted by Red Hat. LICENSEE agrees that
- * it will not delete this copyright notice, trademarks or protective
- * notices from any copy made by LICENSEE.
- *
- * This software is provided "AS-IS" and any express or implied
- * warranties or conditions, including but not limited to any
- * implied warranties of merchantability and fitness for a particular
- * purpose regarding this software. In no event shall Red Hat
- * be liable for any indirect, consequential, or incidental damages,
- * loss of profits or revenue, loss of use or data, or interruption
- * of business, whether the alleged damages are labeled in contract,
- * tort, or indemnity.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * author(s) : Joe deBlaquiere
- *
- * Modified to support NS7520 by Art Shipkowski.
- */
-
-#ifndef __NETARM_MEM_MODULE_REGISTERS_H
-#define __NETARM_MEM_MODULE_REGISTERS_H
-
-/* GEN unit register offsets */
-
-#define	NETARM_MEM_MODULE_BASE		(0xFFC00000)
-
-#define	NETARM_MEM_MODULE_CONFIG	(0x00)
-#define	NETARM_MEM_CS0_BASE_ADDR	(0x10)
-#define	NETARM_MEM_CS0_OPTIONS		(0x14)
-#define	NETARM_MEM_CS1_BASE_ADDR	(0x20)
-#define	NETARM_MEM_CS1_OPTIONS		(0x24)
-#define	NETARM_MEM_CS2_BASE_ADDR	(0x30)
-#define	NETARM_MEM_CS2_OPTIONS		(0x34)
-#define	NETARM_MEM_CS3_BASE_ADDR	(0x40)
-#define	NETARM_MEM_CS3_OPTIONS		(0x44)
-#define	NETARM_MEM_CS4_BASE_ADDR	(0x50)
-#define	NETARM_MEM_CS4_OPTIONS		(0x54)
-
-/* select bitfield defintions */
-
-/* Module Configuration Register ( 0xFFC0_0000 ) */
-
-#define NETARM_MEM_CFG_REFR_COUNT_MASK	(0xFF000000)
-#define NETARM_MEM_CFG_REFRESH_EN	(0x00800000)
-
-#define NETARM_MEM_CFG_REFR_CYCLE_8CLKS	(0x00000000)
-#define NETARM_MEM_CFG_REFR_CYCLE_6CLKS	(0x00200000)
-#define NETARM_MEM_CFG_REFR_CYCLE_5CLKS	(0x00400000)
-#define NETARM_MEM_CFG_REFR_CYCLE_4CLKS	(0x00600000)
-
-#define NETARM_MEM_CFG_PORTC_AMUX	(0x00100000)
-
-#define NETARM_MEM_CFG_A27_ADDR		(0x00080000)
-#define NETARM_MEM_CFG_A27_CS0OE	(0x00000000)
-
-#define NETARM_MEM_CFG_A26_ADDR		(0x00040000)
-#define NETARM_MEM_CFG_A26_CS0WE	(0x00000000)
-
-#define NETARM_MEM_CFG_A25_ADDR		(0x00020000)
-#define NETARM_MEM_CFG_A25_BLAST	(0x00000000)
-
-#define NETARM_MEM_CFG_PORTC_AMUX2	(0x00010000)
-
-
-/* range on this period is about 1 to 275 usec (with 18.432MHz clock)   */
-/* the expression will round down, so make sure to reverse it to verify */
-/* it is what you want. period = [( count + 1 ) * 20] / Fcrystal        */
-/* (note: Fxtal = Fcrystal/5, see HWRefGuide sections 8.2.5 and 11.3.2) */
-
-#define	NETARM_MEM_REFR_PERIOD_USEC(p)	(NETARM_MEM_CFG_REFR_COUNT_MASK & \
-					 (((((NETARM_XTAL_FREQ/(1000))*p)/(20000) \
-					    ) - (1) ) << (24)))
-
-#if 0
-/* range on this period is about 1 to 275 usec (with 18.432MHz clock) */
-/* the expression will round down, so make sure to reverse it toverify */
-/* it is what you want. period = [( count + 1 ) * 4] / Fxtal          */
-
-#define	NETARM_MEM_REFR_PERIOD_USEC(p)	(NETARM_MEM_CFG_REFR_COUNT_MASK & \
-					 (((((NETARM_XTAL_FREQ/(1000))*p)/(4000) \
-					    ) - (1) ) << (24)))
-#endif
-
-/* Base Address Registers (0xFFC0_00X0) */
-
-#define NETARM_MEM_BAR_BASE_MASK	(0xFFFFF000)
-
-/* macro to define base */
-
-#define NETARM_MEM_BAR_BASE(x)		((x) & NETARM_MEM_BAR_BASE_MASK)
-
-#define NETARM_MEM_BAR_DRAM_FP		(0x00000000)
-#define NETARM_MEM_BAR_DRAM_EDO		(0x00000100)
-#define NETARM_MEM_BAR_DRAM_SYNC	(0x00000200)
-
-#define NETARM_MEM_BAR_DRAM_MUX_INT	(0x00000000)
-#define NETARM_MEM_BAR_DRAM_MUX_EXT	(0x00000080)
-
-#define NETARM_MEM_BAR_DRAM_MUX_BAL	(0x00000000)
-#define NETARM_MEM_BAR_DRAM_MUX_UNBAL	(0x00000020)
-
-#define NETARM_MEM_BAR_1BCLK_IDLE	(0x00000010)
-
-#define NETARM_MEM_BAR_DRAM_SEL		(0x00000008)
-
-#define NETARM_MEM_BAR_BURST_EN		(0x00000004)
-
-#define NETARM_MEM_BAR_WRT_PROT		(0x00000002)
-
-#define NETARM_MEM_BAR_VALID		(0x00000001)
-
-/* Option Registers (0xFFC0_00X4) */
-
-/* macro to define which bits of the base are significant */
-
-#define NETARM_MEM_OPT_BASE_USE(x)	((x) & NETARM_MEM_BAR_BASE_MASK)
-
-#define NETARM_MEM_OPT_WAIT_MASK	(0x00000F00)
-
-#define	NETARM_MEM_OPT_WAIT_STATES(x)	(((x) << 8 ) & NETARM_MEM_OPT_WAIT_MASK )
-
-#define NETARM_MEM_OPT_BCYC_1		(0x00000000)
-#define NETARM_MEM_OPT_BCYC_2		(0x00000040)
-#define NETARM_MEM_OPT_BCYC_3		(0x00000080)
-#define NETARM_MEM_OPT_BCYC_4		(0x000000C0)
-
-#define NETARM_MEM_OPT_BSIZE_2		(0x00000000)
-#define NETARM_MEM_OPT_BSIZE_4		(0x00000010)
-#define NETARM_MEM_OPT_BSIZE_8		(0x00000020)
-#define NETARM_MEM_OPT_BSIZE_16		(0x00000030)
-
-#define NETARM_MEM_OPT_32BIT		(0x00000000)
-#define NETARM_MEM_OPT_16BIT		(0x00000004)
-#define NETARM_MEM_OPT_8BIT		(0x00000008)
-#define NETARM_MEM_OPT_32BIT_EXT_ACK	(0x0000000C)
-
-#define NETARM_MEM_OPT_BUS_SIZE_MASK	(0x0000000C)
-
-#define NETARM_MEM_OPT_READ_ASYNC	(0x00000000)
-#define NETARM_MEM_OPT_READ_SYNC	(0x00000002)
-
-#define NETARM_MEM_OPT_WRITE_ASYNC	(0x00000000)
-#define NETARM_MEM_OPT_WRITE_SYNC	(0x00000001)
-
-#ifdef CONFIG_NETARM_NS7520
-/* The NS7520 has a second options register for each chip select */
-#define	NETARM_MEM_CS0_OPTIONS_B  (0x18)
-#define	NETARM_MEM_CS1_OPTIONS_B  (0x28)
-#define	NETARM_MEM_CS2_OPTIONS_B  (0x38)
-#define	NETARM_MEM_CS3_OPTIONS_B  (0x48)
-#define	NETARM_MEM_CS4_OPTIONS_B  (0x58)
-
-/* Option B Registers (0xFFC0_00x8) */
-#define NETARM_MEM_OPTB_SYNC_1_STAGE	(0x00000001)
-#define NETARM_MEM_OPTB_SYNC_2_STAGE	(0x00000002)
-#define NETARM_MEM_OPTB_BCYC_PLUS0	(0x00000000)
-#define NETARM_MEM_OPTB_BCYC_PLUS4	(0x00000004)
-#define NETARM_MEM_OPTB_BCYC_PLUS8	(0x00000008)
-#define NETARM_MEM_OPTB_BCYC_PLUS12	(0x0000000C)
-
-#define NETARM_MEM_OPTB_WAIT_PLUS0	(0x00000000)
-#define NETARM_MEM_OPTB_WAIT_PLUS16	(0x00000010)
-#define NETARM_MEM_OPTB_WAIT_PLUS32	(0x00000020)
-#define NETARM_MEM_OPTB_WAIT_PLUS48	(0x00000030)
-#endif
-
-#endif
diff --git a/arch/arm/include/asm/arch-arm720t/netarm_registers.h b/arch/arm/include/asm/arch-arm720t/netarm_registers.h
deleted file mode 100644
index fa8812879a..0000000000
--- a/arch/arm/include/asm/arch-arm720t/netarm_registers.h
+++ /dev/null
@@ -1,96 +0,0 @@
-/*
- * linux/include/asm-arm/arch-netarm/netarm_registers.h
- *
- * Copyright (C) 2005
- * Art Shipkowski, Videon Central, Inc., <art@videon-central.com>
- *
- * Copyright (C) 2000, 2001 NETsilicon, Inc.
- * Copyright (C) 2000, 2001 WireSpeed Communications Corporation
- *
- * This software is copyrighted by WireSpeed. LICENSEE agrees that
- * it will not delete this copyright notice, trademarks or protective
- * notices from any copy made by LICENSEE.
- *
- * This software is provided "AS-IS" and any express or implied
- * warranties or conditions, including but not limited to any
- * implied warranties of merchantability and fitness for a particular
- * purpose regarding this software. In no event shall WireSpeed
- * be liable for any indirect, consequential, or incidental damages,
- * loss of profits or revenue, loss of use or data, or interruption
- * of business, whether the alleged damages are labeled in contract,
- * tort, or indemnity.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * author(s) : Joe deBlaquiere
- *
- * Modified to support NS7520 by Art Shipkowski.
- */
-
-#ifndef __NET_ARM_REGISTERS_H
-#define __NET_ARM_REGISTERS_H
-
-#include <config.h>
-
-/* fundamental constants : */
-/* the input crystal/clock frequency ( in Hz ) */
-#define	NETARM_XTAL_FREQ_25MHz		(18432000)
-#define	NETARM_XTAL_FREQ_33MHz		(23698000)
-#define	NETARM_XTAL_FREQ_48MHz		(48000000)
-#define	NETARM_XTAL_FREQ_55MHz		(55000000)
-#define NETARM_XTAL_FREQ_EMLIN1		(20000000)
-
-/* the frequency of SYS_CLK */
-#if defined(CONFIG_NETARM_EMLIN)
-
-/* EMLIN board:  33 MHz (exp.) */
-#define	NETARM_PLL_COUNT_VAL		6
-#define NETARM_XTAL_FREQ		NETARM_XTAL_FREQ_25MHz
-
-#elif defined(CONFIG_NETARM_NET40_REV2)
-
-/* NET+40 Rev2 boards:  33 MHz (with NETARM_XTAL_FREQ_25MHz) */
-#define	NETARM_PLL_COUNT_VAL		6
-#define	NETARM_XTAL_FREQ		NETARM_XTAL_FREQ_25MHz
-
-#elif defined(CONFIG_NETARM_NET40_REV4)
-
-/* NET+40 Rev4 boards with EDO must clock slower: 25 MHz (with
-   NETARM_XTAL_FREQ_25MHz) 4 */
-#define	NETARM_PLL_COUNT_VAL		4
-#define	NETARM_XTAL_FREQ		NETARM_XTAL_FREQ_25MHz
-
-#elif defined(CONFIG_NETARM_NET50)
-
-/* NET+50 boards:  40 MHz (with NETARM_XTAL_FREQ_25MHz) */
-#define NETARM_PLL_COUNT_VAL		8
-#define	NETARM_XTAL_FREQ		NETARM_XTAL_FREQ_25MHz
-
-#else	/* CONFIG_NETARM_NS7520 */
-
-#define	NETARM_PLL_COUNT_VAL		0
-
-#if defined(CONFIG_BOARD_UNC20)
-#define	NETARM_XTAL_FREQ		NETARM_XTAL_FREQ_48MHz
-#else
-#define	NETARM_XTAL_FREQ		NETARM_XTAL_FREQ_55MHz
-#endif
-
-#endif
-
-/* #include "arm_registers.h" */
-#include <asm/arch/netarm_gen_module.h>
-#include <asm/arch/netarm_mem_module.h>
-#include <asm/arch/netarm_ser_module.h>
-#include <asm/arch/netarm_eni_module.h>
-#include <asm/arch/netarm_dma_module.h>
-#include <asm/arch/netarm_eth_module.h>
-
-#endif
diff --git a/arch/arm/include/asm/arch-arm720t/netarm_ser_module.h b/arch/arm/include/asm/arch-arm720t/netarm_ser_module.h
deleted file mode 100644
index 6fbae11c8d..0000000000
--- a/arch/arm/include/asm/arch-arm720t/netarm_ser_module.h
+++ /dev/null
@@ -1,347 +0,0 @@
-/*
- * linux/include/asm-arm/arch-netarm/netarm_ser_module.h
- *
- * Copyright (C) 2000 NETsilicon, Inc.
- * Copyright (C) 2000 Red Hat, Inc.
- *
- * This software is copyrighted by Red Hat. LICENSEE agrees that
- * it will not delete this copyright notice, trademarks or protective
- * notices from any copy made by LICENSEE.
- *
- * This software is provided "AS-IS" and any express or implied
- * warranties or conditions, including but not limited to any
- * implied warranties of merchantability and fitness for a particular
- * purpose regarding this software. In no event shall Red Hat
- * be liable for any indirect, consequential, or incidental damages,
- * loss of profits or revenue, loss of use or data, or interruption
- * of business, whether the alleged damages are labeled in contract,
- * tort, or indemnity.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
- *
- * author(s) : Joe deBlaquiere
- *             Clark Williams
- */
-
-#ifndef __NETARM_SER_MODULE_REGISTERS_H
-#define __NETARM_SER_MODULE_REGISTERS_H
-
-#ifndef	__ASSEMBLER__
-
-/* (--sub)#include "types.h" */
-
-/* serial channel control structure */
-typedef struct {
-  u32	ctrl_a;
-  u32	ctrl_b;
-  u32	status_a;
-  u32	bitrate;
-  u32	fifo;
-  u32	rx_buf_timer;
-  u32	rx_char_timer;
-  u32	rx_match;
-  u32	rx_match_mask;
-  u32	ctrl_c;
-  u32	status_b;
-  u32	status_c;
-  u32	fifo_last;
-  u32	unused[3];
-} netarm_serial_channel_t;
-
-#endif
-
-/* SER unit register offsets */
-
-/* #ifdef CONFIG_ARCH_NETARM */
-#define	NETARM_SER_MODULE_BASE		(0xFFD00000)
-/* #else */
-/* extern serial_channel_t netarm_dummy_registers[]; */
-/* #define NETARM_SER_MODULE_BASE		(netarm_dummy_registers) */
-/* #ifndef NETARM_XTAL_FREQ */
-/* #define NETARM_XTAL_FREQ                18432000 */
-/* #endif */
-/* #endif */
-
-/* calculate the sysclk value from the pll setting */
-#define	NETARM_PLLED_SYSCLK_FREQ	(( NETARM_XTAL_FREQ / 5 ) * \
-					 ( NETARM_PLL_COUNT_VAL + 3 ))
-
-#define get_serial_channel(c) (&(((netarm_serial_channel_t *)NETARM_SER_MODULE_BASE)[c]))
-
-#define	NETARM_SER_CH1_CTRL_A		(0x00)
-#define	NETARM_SER_CH1_CTRL_B		(0x04)
-#define	NETARM_SER_CH1_STATUS_A		(0x08)
-#define	NETARM_SER_CH1_BITRATE		(0x0C)
-#define	NETARM_SER_CH1_FIFO		(0x10)
-#define	NETARM_SER_CH1_RX_BUF_TMR	(0x14)
-#define	NETARM_SER_CH1_RX_CHAR_TMR	(0x18)
-#define	NETARM_SER_CH1_RX_MATCH		(0x1c)
-#define	NETARM_SER_CH1_RX_MATCH_MASK	(0x20)
-#define	NETARM_SER_CH1_CTRL_C		(0x24)
-#define	NETARM_SER_CH1_STATUS_B		(0x28)
-#define	NETARM_SER_CH1_STATUS_C		(0x2c)
-#define	NETARM_SER_CH1_FIFO_LAST	(0x30)
-
-#define	NETARM_SER_CH2_CTRL_A		(0x40)
-#define	NETARM_SER_CH2_CTRL_B		(0x44)
-#define	NETARM_SER_CH2_STATUS_A		(0x48)
-#define	NETARM_SER_CH2_BITRATE		(0x4C)
-#define	NETARM_SER_CH2_FIFO		(0x50)
-#define	NETARM_SER_CH2_RX_BUF_TMR	(0x54)
-#define	NETARM_SER_CH2_RX_CHAR_TMR	(0x58)
-#define	NETARM_SER_CH2_RX_MATCH		(0x5c)
-#define	NETARM_SER_CH2_RX_MATCH_MASK	(0x60)
-#define	NETARM_SER_CH2_CTRL_C		(0x64)
-#define	NETARM_SER_CH2_STATUS_B		(0x68)
-#define	NETARM_SER_CH2_STATUS_C		(0x6c)
-#define	NETARM_SER_CH2_FIFO_LAST	(0x70)
-
-/* select bitfield defintions */
-
-/* Control Register A */
-
-#define	NETARM_SER_CTLA_ENABLE		(0x80000000)
-#define	NETARM_SER_CTLA_BRK		(0x40000000)
-
-#define	NETARM_SER_CTLA_STICKP		(0x20000000)
-
-#define	NETARM_SER_CTLA_P_EVEN		(0x18000000)
-#define	NETARM_SER_CTLA_P_ODD		(0x08000000)
-#define	NETARM_SER_CTLA_P_NONE		(0x00000000)
-
-/* if you read the errata, you will find that the STOP bits don't work right */
-#define	NETARM_SER_CTLA_2STOP		(0x00000000)
-#define	NETARM_SER_CTLA_3STOP		(0x04000000)
-
-#define	NETARM_SER_CTLA_5BITS		(0x00000000)
-#define	NETARM_SER_CTLA_6BITS		(0x01000000)
-#define	NETARM_SER_CTLA_7BITS		(0x02000000)
-#define	NETARM_SER_CTLA_8BITS		(0x03000000)
-
-#define	NETARM_SER_CTLA_CTSTX		(0x00800000)
-#define	NETARM_SER_CTLA_RTSRX		(0x00400000)
-
-#define	NETARM_SER_CTLA_LOOP_REM	(0x00200000)
-#define	NETARM_SER_CTLA_LOOP_LOC	(0x00100000)
-
-#define	NETARM_SER_CTLA_GPIO2		(0x00080000)
-#define	NETARM_SER_CTLA_GPIO1		(0x00040000)
-
-#define	NETARM_SER_CTLA_DTR_EN		(0x00020000)
-#define	NETARM_SER_CTLA_RTS_EN		(0x00010000)
-
-#define	NETARM_SER_CTLA_IE_RX_BRK	(0x00008000)
-#define	NETARM_SER_CTLA_IE_RX_FRMERR	(0x00004000)
-#define	NETARM_SER_CTLA_IE_RX_PARERR	(0x00002000)
-#define	NETARM_SER_CTLA_IE_RX_OVERRUN	(0x00001000)
-#define	NETARM_SER_CTLA_IE_RX_RDY	(0x00000800)
-#define	NETARM_SER_CTLA_IE_RX_HALF	(0x00000400)
-#define	NETARM_SER_CTLA_IE_RX_FULL	(0x00000200)
-#define	NETARM_SER_CTLA_IE_RX_DMAEN	(0x00000100)
-#define	NETARM_SER_CTLA_IE_RX_DCD	(0x00000080)
-#define	NETARM_SER_CTLA_IE_RX_RI	(0x00000040)
-#define	NETARM_SER_CTLA_IE_RX_DSR	(0x00000020)
-
-#define NETARM_SER_CTLA_IE_RX_ALL	(NETARM_SER_CTLA_IE_RX_BRK \
-					|NETARM_SER_CTLA_IE_RX_FRMERR \
-					|NETARM_SER_CTLA_IE_RX_PARERR \
-					|NETARM_SER_CTLA_IE_RX_OVERRUN \
-					|NETARM_SER_CTLA_IE_RX_RDY \
-					|NETARM_SER_CTLA_IE_RX_HALF \
-					|NETARM_SER_CTLA_IE_RX_FULL \
-					|NETARM_SER_CTLA_IE_RX_DMAEN \
-					|NETARM_SER_CTLA_IE_RX_DCD \
-					|NETARM_SER_CTLA_IE_RX_RI \
-					|NETARM_SER_CTLA_IE_RX_DSR)
-
-#define	NETARM_SER_CTLA_IE_TX_CTS	(0x00000010)
-#define	NETARM_SER_CTLA_IE_TX_EMPTY	(0x00000008)
-#define	NETARM_SER_CTLA_IE_TX_HALF	(0x00000004)
-#define	NETARM_SER_CTLA_IE_TX_FULL	(0x00000002)
-#define	NETARM_SER_CTLA_IE_TX_DMAEN	(0x00000001)
-
-#define NETARM_SER_CTLA_IE_TX_ALL	(NETARM_SER_CTLA_IE_TX_CTS \
-					|NETARM_SER_CTLA_IE_TX_EMPTY \
-					|NETARM_SER_CTLA_IE_TX_HALF \
-					|NETARM_SER_CTLA_IE_TX_FULL \
-					|NETARM_SER_CTLA_IE_TX_DMAEN)
-
-/* Control Register B */
-
-#define	NETARM_SER_CTLB_MATCH1_EN	(0x80000000)
-#define	NETARM_SER_CTLB_MATCH2_EN	(0x40000000)
-#define	NETARM_SER_CTLB_MATCH3_EN	(0x20000000)
-#define	NETARM_SER_CTLB_MATCH4_EN	(0x10000000)
-
-#define	NETARM_SER_CTLB_RBGT_EN		(0x08000000)
-#define	NETARM_SER_CTLB_RCGT_EN		(0x04000000)
-
-#define	NETARM_SER_CTLB_UART_MODE	(0x00000000)
-#define	NETARM_SER_CTLB_HDLC_MODE	(0x00100000)
-#define	NETARM_SER_CTLB_SPI_MAS_MODE	(0x00200000)
-#define	NETARM_SER_CTLB_SPI_SLV_MODE	(0x00300000)
-
-#define	NETARM_SER_CTLB_REV_BIT_ORDER	(0x00080000)
-
-#define	NETARM_SER_CTLB_MAM1		(0x00040000)
-#define	NETARM_SER_CTLB_MAM2		(0x00020000)
-
-/* Status Register A */
-
-#define	NETARM_SER_STATA_MATCH1		(0x80000000)
-#define	NETARM_SER_STATA_MATCH2		(0x40000000)
-#define	NETARM_SER_STATA_MATCH3		(0x20000000)
-#define	NETARM_SER_STATA_MATCH4		(0x10000000)
-
-#define	NETARM_SER_STATA_BGAP		(0x80000000)
-#define	NETARM_SER_STATA_CGAP		(0x40000000)
-
-#define	NETARM_SER_STATA_RX_1B		(0x00100000)
-#define	NETARM_SER_STATA_RX_2B		(0x00200000)
-#define	NETARM_SER_STATA_RX_3B		(0x00300000)
-#define	NETARM_SER_STATA_RX_4B		(0x00000000)
-
-/* downshifted values */
-
-#define	NETARM_SER_STATA_RXFDB_1BYTES	(0x001)
-#define	NETARM_SER_STATA_RXFDB_2BYTES	(0x002)
-#define	NETARM_SER_STATA_RXFDB_3BYTES	(0x003)
-#define	NETARM_SER_STATA_RXFDB_4BYTES	(0x000)
-
-#define	NETARM_SER_STATA_RXFDB_MASK	(0x00300000)
-#define	NETARM_SER_STATA_RXFDB(x)	(((x) & NETARM_SER_STATA_RXFDB_MASK) \
-					 >> 20)
-
-#define	NETARM_SER_STATA_DCD		(0x00080000)
-#define	NETARM_SER_STATA_RI		(0x00040000)
-#define	NETARM_SER_STATA_DSR		(0x00020000)
-#define	NETARM_SER_STATA_CTS		(0x00010000)
-
-#define	NETARM_SER_STATA_RX_BRK		(0x00008000)
-#define	NETARM_SER_STATA_RX_FRMERR	(0x00004000)
-#define	NETARM_SER_STATA_RX_PARERR	(0x00002000)
-#define	NETARM_SER_STATA_RX_OVERRUN	(0x00001000)
-#define	NETARM_SER_STATA_RX_RDY		(0x00000800)
-#define	NETARM_SER_STATA_RX_HALF	(0x00000400)
-#define	NETARM_SER_STATA_RX_CLOSED	(0x00000200)
-#define	NETARM_SER_STATA_RX_FULL	(0x00000100)
-#define	NETARM_SER_STATA_RX_DCD		(0x00000080)
-#define	NETARM_SER_STATA_RX_RI		(0x00000040)
-#define	NETARM_SER_STATA_RX_DSR		(0x00000020)
-
-#define	NETARM_SER_STATA_TX_CTS		(0x00000010)
-#define	NETARM_SER_STATA_TX_RDY		(0x00000008)
-#define	NETARM_SER_STATA_TX_HALF	(0x00000004)
-#define	NETARM_SER_STATA_TX_FULL	(0x00000002)
-#define	NETARM_SER_STATA_TX_DMAEN	(0x00000001)
-
-/* you have to clear all receive signals to get the fifo to move forward */
-#define NETARM_SER_STATA_CLR_ALL	(NETARM_SER_STATA_RX_BRK | \
-					 NETARM_SER_STATA_RX_FRMERR | \
-					 NETARM_SER_STATA_RX_PARERR | \
-					 NETARM_SER_STATA_RX_OVERRUN | \
-					 NETARM_SER_STATA_RX_HALF | \
-					 NETARM_SER_STATA_RX_CLOSED | \
-					 NETARM_SER_STATA_RX_FULL | \
-					 NETARM_SER_STATA_RX_DCD | \
-					 NETARM_SER_STATA_RX_RI | \
-					 NETARM_SER_STATA_RX_DSR | \
-					 NETARM_SER_STATA_TX_CTS )
-
-/* Bit Rate Registers */
-
-#define	NETARM_SER_BR_EN		(0x80000000)
-#define	NETARM_SER_BR_TMODE		(0x40000000)
-
-#define	NETARM_SER_BR_RX_CLK_INT	(0x00000000)
-#define	NETARM_SER_BR_RX_CLK_EXT	(0x20000000)
-#define	NETARM_SER_BR_TX_CLK_INT	(0x00000000)
-#define	NETARM_SER_BR_TX_CLK_EXT	(0x10000000)
-
-#define	NETARM_SER_BR_RX_CLK_DRV	(0x08000000)
-#define	NETARM_SER_BR_TX_CLK_DRV	(0x04000000)
-
-#define	NETARM_SER_BR_CLK_EXT_5		(0x00000000)
-#define	NETARM_SER_BR_CLK_SYSTEM	(0x01000000)
-#define	NETARM_SER_BR_CLK_OUT1A		(0x02000000)
-#define	NETARM_SER_BR_CLK_OUT2A		(0x03000000)
-
-#define	NETARM_SER_BR_TX_CLK_INV	(0x00800000)
-#define	NETARM_SER_BR_RX_CLK_INV	(0x00400000)
-
-/* complete settings assuming system clock input is 18MHz */
-
-#define	NETARM_SER_BR_MASK		(0x000007FF)
-
-/* bit rate determined from equation Fbr = Fxtal / [ 10 * ( N + 1 ) ] */
-/* from section 7.5.4 of HW Ref Guide */
-
-/* #ifdef CONFIG_NETARM_PLL_BYPASS */
-#define	NETARM_SER_BR_X16(x)	( NETARM_SER_BR_EN |			\
-				  NETARM_SER_BR_RX_CLK_INT |		\
-				  NETARM_SER_BR_TX_CLK_INT |		\
-				  NETARM_SER_BR_CLK_EXT_5 |		\
-				  ( ( ( ( NETARM_XTAL_FREQ /		\
-				          ( x * 10 ) ) - 1 ) /	16 ) &	\
-				    NETARM_SER_BR_MASK ) )
-/*
-#else
-#define	NETARM_SER_BR_X16(x)	( NETARM_SER_BR_EN |			\
-				  NETARM_SER_BR_RX_CLK_INT |		\
-				  NETARM_SER_BR_TX_CLK_INT |		\
-				  NETARM_SER_BR_CLK_SYSTEM |		\
-				  ( ( ( ( NETARM_PLLED_SYSCLK_FREQ /		\
-				          ( x * 2 ) ) - 1 ) /	16 ) &	\
-				    NETARM_SER_BR_MASK ) )
-#endif
-*/
-
-/* Receive Buffer Gap Timer */
-
-#define	NETARM_SER_RX_GAP_TIMER_EN	(0x80000000)
-#define	NETARM_SER_RX_GAP_MASK		(0x00003FFF)
-
-/* rx gap is a function of bit rate x */
-
-/* #ifdef CONFIG_NETARM_PLL_BYPASS */
-#define	NETARM_SER_RXGAP(x)	( NETARM_SER_RX_GAP_TIMER_EN |		\
-				  ( ( ( ( 10 * NETARM_XTAL_FREQ ) /	\
-				        ( x * 5 * 512 ) ) - 1 ) &	\
-			              NETARM_SER_RX_GAP_MASK ) )
-/*
-#else
-#define	NETARM_SER_RXGAP(x)	( NETARM_SER_RX_GAP_TIMER_EN |			\
-				  ( ( ( ( 2 * NETARM_PLLED_SYSCLK_FREQ ) /	\
-				        ( x * 512 ) ) - 1 ) &			\
-			              NETARM_SER_RX_GAP_MASK ) )
-#endif
-*/
-
-#if 0
-#define	NETARM_SER_RXGAP(x)	( NETARM_SER_RX_GAP_TIMER_EN |		\
-				  ( ( ( ( 2 * NETARM_PLLED_SYSCLK_FREQ ) /	\
-				        ( x * 5 * 512 ) ) - 1 ) &	\
-			              NETARM_SER_RX_GAP_MASK ) )
-#define	NETARM_SER_RXGAP(x)	( NETARM_SER_RX_GAP_TIMER_EN |		\
-				  ( ( ( ( 10 * NETARM_XTAL_FREQ ) /	\
-				        ( x * 512 ) ) - 1 ) &	\
-			              NETARM_SER_RX_GAP_MASK ) )
-#endif
-
-#define MIN_BAUD_RATE        600
-#define MAX_BAUD_RATE     115200
-
-/* the default BAUD rate for the BOOTLOADER, there is a separate */
-/* setting in the serial driver <arch/armnommu/drivers/char/serial-netarm.h> */
-#define DEFAULT_BAUD_RATE 9600
-#define NETARM_SER_FIFO_SIZE 32
-#define MIN_GAP 0
-
-#endif
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index e4abac7c8f..786a6567a5 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -59,7 +59,6 @@ COBJS-$(CONFIG_MVGBE) += mvgbe.o
 COBJS-$(CONFIG_NATSEMI) += natsemi.o
 COBJS-$(CONFIG_DRIVER_NE2000) += ne2000.o ne2000_base.o
 COBJS-$(CONFIG_DRIVER_AX88796L) += ax88796.o ne2000_base.o
-COBJS-$(CONFIG_DRIVER_NETARMETH) += netarm_eth.o
 COBJS-$(CONFIG_NETCONSOLE) += netconsole.o
 COBJS-$(CONFIG_NS8382X) += ns8382x.o
 COBJS-$(CONFIG_PCNET) += pcnet.o
diff --git a/drivers/net/netarm_eth.c b/drivers/net/netarm_eth.c
deleted file mode 100644
index 325f16c3a8..0000000000
--- a/drivers/net/netarm_eth.c
+++ /dev/null
@@ -1,352 +0,0 @@
-/*
- * Copyright (C) 2004 IMMS gGmbH <www.imms.de>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- *
- * author(s): Thomas Elste, <info@elste.org>
- *            (some parts derived from uCLinux Netarm Ethernet Driver)
- */
-
-
-#include <common.h>
-#include <command.h>
-#include <net.h>
-#include "netarm_eth.h"
-#include <asm/arch/netarm_registers.h>
-
-static int na_mii_poll_busy (void);
-
-static void na_get_mac_addr (void)
-{
-	unsigned short p[3];
-	char *m_addr;
-	char ethaddr[20];
-
-	m_addr = (char *) p;
-
-	p[0] = (unsigned short) GET_EADDR (NETARM_ETH_SAL_STATION_ADDR_1);
-	p[1] = (unsigned short) GET_EADDR (NETARM_ETH_SAL_STATION_ADDR_2);
-	p[2] = (unsigned short) GET_EADDR (NETARM_ETH_SAL_STATION_ADDR_3);
-
-	sprintf (ethaddr, "%02X:%02X:%02X:%02X:%02X:%02X",
-		 m_addr[0], m_addr[1],
-		 m_addr[2], m_addr[3], m_addr[4], m_addr[5]);
-
-	printf ("HW-MAC Address:  %s\n", ethaddr);
-
-	/* set env, todo: check if already an adress is set */
-	setenv ("ethaddr", ethaddr);
-}
-
-static void na_mii_write (int reg, int value)
-{
-	int mii_addr;
-
-	/* Select register */
-	mii_addr = CONFIG_SYS_ETH_PHY_ADDR + reg;
-	SET_EADDR (NETARM_ETH_MII_ADDR, mii_addr);
-	/* Write value */
-	SET_EADDR (NETARM_ETH_MII_WRITE, value);
-	na_mii_poll_busy ();
-}
-
-static unsigned int na_mii_read (int reg)
-{
-	int mii_addr, val;
-
-	/* Select register */
-	mii_addr = CONFIG_SYS_ETH_PHY_ADDR + reg;
-	SET_EADDR (NETARM_ETH_MII_ADDR, mii_addr);
-	/* do one management cycle */
-	SET_EADDR (NETARM_ETH_MII_CMD,
-		   GET_EADDR (NETARM_ETH_MII_CMD) | NETARM_ETH_MIIC_RSTAT);
-	na_mii_poll_busy ();
-	/* Return read value */
-	val = GET_EADDR (NETARM_ETH_MII_READ);
-	return val;
-}
-
-static int na_mii_poll_busy (void)
-{
-	ulong start;
-	/* arm simple, non interrupt dependent timer */
-	start = get_timer(0));
-	while (get_timer(start) < NA_MII_POLL_BUSY_DELAY) {
-		if (!(GET_EADDR (NETARM_ETH_MII_IND) & NETARM_ETH_MIII_BUSY)) {
-			return 1;
-		}
-	}
-	printf ("na_mii_busy timeout\n");
-	return (0);
-}
-
-static int na_mii_identify_phy (void)
-{
-	int id_reg_a = 0;
-
-	/* get phy id register */
-	id_reg_a = na_mii_read (MII_PHY_ID);
-
-	if (id_reg_a == 0x0043) {
-		/* This must be an Enable or a Lucent LU3X31 PHY chip */
-		return 1;
-	} else if (id_reg_a == 0x0013) {
-		/* it is an Intel LXT971A */
-		return 1;
-	}
-	return (0);
-}
-
-static int na_mii_negotiate (void)
-{
-	int i = 0;
-
-	/* Enable auto-negotiation */
-	na_mii_write (MII_PHY_AUTONEGADV, 0x01e1);
-	/* FIXME: 0x01E1 is 100Mb half and full duplex, 0x0061 is 10Mb only */
-	/* Restart auto-negotiation */
-	na_mii_write (MII_PHY_CONTROL, 0x1200);
-
-	/* status register is 0xffff after setting the autoneg restart bit */
-	while (na_mii_read (MII_PHY_STATUS) == 0xffff) {
-		i++;
-	}
-
-	/* na_mii_read uses the timer already, so we can't use it again for
-	   timeout checking.
-	   Instead we just try some times.
-	 */
-	for (i = 0; i < 40000; i++) {
-		if ((na_mii_read (MII_PHY_STATUS) & 0x0024) == 0x0024) {
-			return 0;
-		}
-	}
-	/*
-	   printf("*Warning* autonegotiation timeout, status: 0x%x\n",na_mii_read(MII_PHY_STATUS));
-	 */
-	return (1);
-}
-
-static unsigned int na_mii_check_speed (void)
-{
-	unsigned int status;
-
-	/* Read Status register */
-	status = na_mii_read (MII_PHY_STATUS);
-	/* Check link status.  If 0, default to 100 Mbps. */
-	if ((status & 0x0004) == 0) {
-		printf ("*Warning* no link detected, set default speed to 100Mbs\n");
-		return 1;
-	} else {
-		if ((na_mii_read (17) & 0x4000) != 0) {
-			printf ("100Mbs link detected\n");
-			return 1;
-		} else {
-			printf ("10Mbs link detected\n");
-			return 0;
-		}
-	}
-	return 0;
-}
-
-static int reset_eth (void)
-{
-	int pt;
-	ulong start;
-
-	na_get_mac_addr ();
-	pt = na_mii_identify_phy ();
-
-	/* reset the phy */
-	na_mii_write (MII_PHY_CONTROL, 0x8000);
-	start = get_timer(0);
-	while (get_timer(start) < NA_MII_NEGOTIATE_DELAY) {
-		if ((na_mii_read (MII_PHY_STATUS) & 0x8000) == 0) {
-			break;
-		}
-	}
-	if (get_timer(start) >= NA_MII_NEGOTIATE_DELAY)
-		printf ("phy reset timeout\n");
-
-	/* set the PCS reg */
-	SET_EADDR (NETARM_ETH_PCS_CFG, NETARM_ETH_PCSC_CLKS_25M |
-		   NETARM_ETH_PCSC_ENJAB | NETARM_ETH_PCSC_NOCFR);
-
-	na_mii_negotiate ();
-	na_mii_check_speed ();
-
-	/* Delay 10 millisecond.  (Maybe this should be 1 second.) */
-	udelay (10000);
-
-	/* Turn receive on.
-	   Enable statistics register autozero on read.
-	   Do not insert MAC address on transmit.
-	   Do not enable special test modes.  */
-	SET_EADDR (NETARM_ETH_STL_CFG,
-		   (NETARM_ETH_STLC_AUTOZ | NETARM_ETH_STLC_RXEN));
-
-	/* Set the inter-packet gap delay to 0.96us for MII.
-	   The NET+ARM H/W Reference Guide indicates that the Back-to-back IPG
-	   Gap Timer Register should be set to 0x15 and the Non Back-to-back IPG
-	   Gap Timer Register should be set to 0x00000C12 for the MII PHY. */
-	SET_EADDR (NETARM_ETH_B2B_IPG_GAP_TMR, 0x15);
-	SET_EADDR (NETARM_ETH_NB2B_IPG_GAP_TMR, 0x00000C12);
-
-	/* Add CRC to end of packets.
-	   Pad packets to minimum length of 64 bytes.
-	   Allow unlimited length transmit packets.
-	   Receive all broadcast packets.
-	   NOTE:  Multicast addressing is NOT enabled here currently. */
-	SET_EADDR (NETARM_ETH_MAC_CFG,
-		   (NETARM_ETH_MACC_CRCEN |
-		    NETARM_ETH_MACC_PADEN | NETARM_ETH_MACC_HUGEN));
-	SET_EADDR (NETARM_ETH_SAL_FILTER, NETARM_ETH_SALF_BROAD);
-
-	/* enable fifos */
-	SET_EADDR (NETARM_ETH_GEN_CTRL,
-		   (NETARM_ETH_GCR_ERX | NETARM_ETH_GCR_ETX));
-
-	return (0);
-}
-
-
-extern int eth_init (bd_t * bd)
-{
-	reset_eth ();
-	return 0;
-}
-
-extern void eth_halt (void)
-{
-	SET_EADDR (NETARM_ETH_GEN_CTRL, 0);
-}
-
-/* Get a data block via Ethernet */
-extern int eth_rx (void)
-{
-	int i;
-	unsigned short rxlen;
-	unsigned int *addr;
-	unsigned int rxstatus, lastrxlen;
-	char *pa;
-
-	/* RXBR is 1, data block was received */
-	if ((GET_EADDR (NETARM_ETH_GEN_STAT) & NETARM_ETH_GST_RXBR) == 0)
-		return 0;
-
-	/* get status register and the length of received block */
-	rxstatus = GET_EADDR (NETARM_ETH_RX_STAT);
-	rxlen = (rxstatus & NETARM_ETH_RXSTAT_SIZE) >> 16;
-
-	if (rxlen == 0)
-		return 0;
-
-	/* clear RXBR to make fifo available */
-	SET_EADDR (NETARM_ETH_GEN_STAT,
-		   GET_EADDR (NETARM_ETH_GEN_STAT) & ~NETARM_ETH_GST_RXBR);
-
-	/* clear TXBC to make fifo available */
-	/* According to NETARM50 data manual you just have to clear
-	   RXBR but that has no effect. Only after clearing TXBC the
-	   Fifo becomes readable. */
-	SET_EADDR (NETARM_ETH_GEN_STAT,
-		   GET_EADDR (NETARM_ETH_GEN_STAT) & ~NETARM_ETH_GST_TXBC);
-
-	addr = (unsigned int *) NetRxPackets[0];
-	pa = (char *) NetRxPackets[0];
-
-	/* read the fifo */
-	for (i = 0; i < rxlen / 4; i++) {
-		*addr = GET_EADDR (NETARM_ETH_FIFO_DAT1);
-		addr++;
-	}
-
-	if (GET_EADDR (NETARM_ETH_GEN_STAT) & NETARM_ETH_GST_RXREGR) {
-		/* RXFDB indicates wether the last word is 1,2,3 or 4 bytes long */
-		lastrxlen =
-			(GET_EADDR (NETARM_ETH_GEN_STAT) &
-			 NETARM_ETH_GST_RXFDB) >> 28;
-		*addr = GET_EADDR (NETARM_ETH_FIFO_DAT1);
-		switch (lastrxlen) {
-		case 1:
-			*addr &= 0xff000000;
-			break;
-		case 2:
-			*addr &= 0xffff0000;
-			break;
-		case 3:
-			*addr &= 0xffffff00;
-			break;
-		}
-	}
-
-	/* Pass the packet up to the protocol layers. */
-	NetReceive (NetRxPackets[0], rxlen);
-
-	return rxlen;
-}
-
-/* Send a data block via Ethernet. */
-extern int eth_send(void *packet, int length)
-{
-	int i, length32;
-	char *pa;
-	unsigned int *pa32, lastp = 0, rest;
-
-	pa = (char *) packet;
-	pa32 = (unsigned int *) packet;
-	length32 = length / 4;
-	rest = length % 4;
-
-	/* make sure there's no garbage in the last word */
-	switch (rest) {
-	case 0:
-		lastp = pa32[length32];
-		length32--;
-		break;
-	case 1:
-		lastp = pa32[length32] & 0x000000ff;
-		break;
-	case 2:
-		lastp = pa32[length32] & 0x0000ffff;
-		break;
-	case 3:
-		lastp = pa32[length32] & 0x00ffffff;
-		break;
-	}
-
-	/* write to the fifo */
-	for (i = 0; i < length32; i++)
-		SET_EADDR (NETARM_ETH_FIFO_DAT1, pa32[i]);
-
-	/* the last word is written to an extra register, this
-	   starts the transmission */
-	SET_EADDR (NETARM_ETH_FIFO_DAT2, lastp);
-
-	/* NETARM_ETH_TXSTAT_TXOK should be checked, to know if the transmission
-	   went fine. But we can't use the timer for a timeout loop because
-	   of it is used already in upper layers. So we just try some times. */
-	i = 0;
-	while (i < 50000) {
-		if ((GET_EADDR (NETARM_ETH_TX_STAT) & NETARM_ETH_TXSTAT_TXOK)
-		    == NETARM_ETH_TXSTAT_TXOK)
-			return 0;
-		i++;
-	}
-
-	printf ("eth_send timeout\n");
-	return 1;
-}
diff --git a/drivers/net/netarm_eth.h b/drivers/net/netarm_eth.h
deleted file mode 100644
index 8edab82da3..0000000000
--- a/drivers/net/netarm_eth.h
+++ /dev/null
@@ -1,42 +0,0 @@
-/*
- * Copyright (C) 2003 IMMS gGmbH <www.imms.de>
- *
- * This program is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of
- * the License, or (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
- * MA 02111-1307 USA
- *
- * author(s): Thomas Elste, <info@elste.org>
- */
-
-#include <asm/types.h>
-#include <config.h>
-
-#ifdef CONFIG_DRIVER_NETARMETH
-
-#define SET_EADDR(ad,val) *(volatile unsigned int*)(ad + NETARM_ETH_MODULE_BASE) = val
-#define GET_EADDR(ad) (*(volatile unsigned int*)(ad + NETARM_ETH_MODULE_BASE))
-
-#define NA_MII_POLL_BUSY_DELAY 900
-
-/* MII negotiation timeout value
-   500 jiffies = 5 seconds */
-#define NA_MII_NEGOTIATE_DELAY 30
-
-/* Registers in the physical layer chip */
-#define MII_PHY_CONTROL		0
-#define MII_PHY_STATUS		1
-#define MII_PHY_ID              2
-#define MII_PHY_AUTONEGADV	4
-
-#endif /* CONFIG_DRIVER_NETARMETH */
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 8151d2e0f4..b6d20f8446 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -45,7 +45,6 @@ COBJS-$(CONFIG_IXP_SERIAL) += serial_ixp.o
 COBJS-$(CONFIG_KS8695_SERIAL) += serial_ks8695.o
 COBJS-$(CONFIG_MAX3100_SERIAL) += serial_max3100.o
 COBJS-$(CONFIG_MXC_UART) += serial_mxc.o
-COBJS-$(CONFIG_NETARM_SERIAL) += serial_netarm.o
 COBJS-$(CONFIG_PL010_SERIAL) += serial_pl01x.o
 COBJS-$(CONFIG_PL011_SERIAL) += serial_pl01x.o
 COBJS-$(CONFIG_PXA_SERIAL) += serial_pxa.o
diff --git a/drivers/serial/serial.c b/drivers/serial/serial.c
index 44bb089dee..f5f43a6ddc 100644
--- a/drivers/serial/serial.c
+++ b/drivers/serial/serial.c
@@ -105,7 +105,6 @@ serial_initfunc(ks8695_serial_initialize);
 serial_initfunc(lh7a40x_serial_initialize);
 serial_initfunc(max3100_serial_initialize);
 serial_initfunc(mxc_serial_initialize);
-serial_initfunc(netarm_serial_initialize);
 serial_initfunc(pl01x_serial_initialize);
 serial_initfunc(s3c44b0_serial_initialize);
 serial_initfunc(sa1100_serial_initialize);
@@ -201,7 +200,6 @@ void serial_initialize(void)
 	lh7a40x_serial_initialize();
 	max3100_serial_initialize();
 	mxc_serial_initialize();
-	netarm_serial_initialize();
 	pl01x_serial_initialize();
 	s3c44b0_serial_initialize();
 	sa1100_serial_initialize();
diff --git a/drivers/serial/serial_netarm.c b/drivers/serial/serial_netarm.c
deleted file mode 100644
index 44d7c500c7..0000000000
--- a/drivers/serial/serial_netarm.c
+++ /dev/null
@@ -1,204 +0,0 @@
-/*
- * Serial Port stuff - taken from Linux
- *
- * (C) Copyright 2002
- * MAZeT GmbH <www.mazet.de>
- * Stephan Linz <linz@mazet.de>, <linz@li-pro.net>
- *
- * (c) 2004
- * IMMS gGmbH <www.imms.de>
- * Thomas Elste <info@elste.org>
- *
- * See file CREDITS for list of people who contributed to this
- * project.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- * GNU General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
- *
- */
-
-#include <common.h>
-#include <asm/hardware.h>
-
-DECLARE_GLOBAL_DATA_PTR;
-
-#define PORTA	(*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_PORTA))
-#if !defined(CONFIG_NETARM_NS7520)
-#define PORTB	(*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_PORTB))
-#else
-#define PORTC	(*(volatile unsigned int *)(NETARM_GEN_MODULE_BASE + NETARM_GEN_PORTC))
-#endif
-
-/* wait until transmitter is ready for another character */
-#define TXWAITRDY(registers)							\
-{										\
-	ulong tmo = get_timer(0) + 1 * CONFIG_SYS_HZ;					\
-	while (((registers)->status_a & NETARM_SER_STATA_TX_RDY) == 0 )	{	\
-		if (get_timer(0) > tmo)						\
-			break;							\
-	}									\
-}
-
-
-volatile netarm_serial_channel_t *serial_reg_ch1 = get_serial_channel(0);
-volatile netarm_serial_channel_t *serial_reg_ch2 = get_serial_channel(1);
-
-extern void _netarm_led_FAIL1(void);
-
-/*
- * Setup both serial i/f with given baudrate
- */
-static void netarm_serial_setbrg(void)
-{
-	/* set 0 ... make sure pins are configured for serial */
-#if !defined(CONFIG_NETARM_NS7520)
-	PORTA = PORTB =
-		NETARM_GEN_PORT_MODE (0xef) | NETARM_GEN_PORT_DIR (0xe0);
-#else
-	PORTA = NETARM_GEN_PORT_MODE (0xef) | NETARM_GEN_PORT_DIR (0xe0);
-	PORTC = NETARM_GEN_PORT_CSF (0xef) | NETARM_GEN_PORT_MODE (0xef) | NETARM_GEN_PORT_DIR (0xe0);
-#endif
-
-	/* first turn em off */
-	serial_reg_ch1->ctrl_a = serial_reg_ch2->ctrl_a = 0;
-
-	/* clear match register, we don't need it */
-	serial_reg_ch1->rx_match = serial_reg_ch2->rx_match = 0;
-
-	/* setup bit rate generator and rx buffer gap timer (1 byte only) */
-	if ((gd->baudrate >= MIN_BAUD_RATE)
-	    && (gd->baudrate <= MAX_BAUD_RATE)) {
-		serial_reg_ch1->bitrate = serial_reg_ch2->bitrate =
-			NETARM_SER_BR_X16 (gd->baudrate);
-		serial_reg_ch1->rx_buf_timer = serial_reg_ch2->rx_buf_timer =
-			0;
-		serial_reg_ch1->rx_char_timer = serial_reg_ch2->rx_char_timer =
-			NETARM_SER_RXGAP (gd->baudrate);
-	} else {
-		hang ();
-	}
-
-	/* setup port mode */
-	serial_reg_ch1->ctrl_b = serial_reg_ch2->ctrl_b =
-		( NETARM_SER_CTLB_RCGT_EN |
-		  NETARM_SER_CTLB_UART_MODE);
-	serial_reg_ch1->ctrl_a = serial_reg_ch2->ctrl_a =
-		( NETARM_SER_CTLA_ENABLE |
-		  NETARM_SER_CTLA_P_NONE |
-		  /* see errata */
-		  NETARM_SER_CTLA_2STOP |
-		  NETARM_SER_CTLA_8BITS |
-		  NETARM_SER_CTLA_DTR_EN |
-		  NETARM_SER_CTLA_RTS_EN);
-}
-
-
-/*
- * Initialise the serial port with the given baudrate. The settings
- * are always 8 data bits, no parity, 1 stop bit, no start bits.
- */
-static int netarm_serial_init(void)
-{
-	serial_setbrg ();
-	return 0;
-}
-
-
-/*
- * Output a single byte to the serial port.
- */
-static void netarm_serial_putc(const char c)
-{
-	volatile unsigned char *fifo;
-
-	/* If \n, also do \r */
-	if (c == '\n')
-		serial_putc ('\r');
-
-	fifo = (volatile unsigned char *) &(serial_reg_ch1->fifo);
-	TXWAITRDY (serial_reg_ch1);
-	*fifo = c;
-}
-
-/*
- * Test of a single byte from the serial port. Returns 1 on success, 0
- * otherwise.
- */
-static int netarm_serial_tstc(void)
-{
-	return serial_reg_ch1->status_a & NETARM_SER_STATA_RX_RDY;
-}
-
-/*
- * Read a single byte from the serial port. Returns 1 on success, 0
- * otherwise.
- */
-static int netarm_serial_getc(void)
-{
-	unsigned int ch_uint;
-	volatile unsigned int *fifo;
-	volatile unsigned char *fifo_char = NULL;
-	int buf_count = 0;
-
-	while (!(serial_reg_ch1->status_a & NETARM_SER_STATA_RX_RDY))
-		/* NOP */ ;
-
-	fifo = (volatile unsigned int *) &(serial_reg_ch1->fifo);
-	fifo_char = (unsigned char *) &ch_uint;
-	ch_uint = *fifo;
-
-	buf_count = NETARM_SER_STATA_RXFDB (serial_reg_ch1->status_a);
-	switch (buf_count) {
-	case NETARM_SER_STATA_RXFDB_4BYTES:
-		buf_count = 4;
-		break;
-	case NETARM_SER_STATA_RXFDB_3BYTES:
-		buf_count = 3;
-		break;
-	case NETARM_SER_STATA_RXFDB_2BYTES:
-		buf_count = 2;
-		break;
-	case NETARM_SER_STATA_RXFDB_1BYTES:
-		buf_count = 1;
-		break;
-	default:
-		/* panic, be never here */
-		break;
-	}
-
-	serial_reg_ch1->status_a |= NETARM_SER_STATA_RX_CLOSED;
-
-	return ch_uint & 0xff;
-}
-
-static struct serial_device netarm_serial_drv = {
-	.name	= "netarm_serial",
-	.start	= netarm_serial_init,
-	.stop	= NULL,
-	.setbrg	= netarm_serial_setbrg,
-	.putc	= netarm_serial_putc,
-	.puts	= default_serial_puts,
-	.getc	= netarm_serial_getc,
-	.tstc	= netarm_serial_tstc,
-};
-
-void netarm_serial_initialize(void)
-{
-	serial_register(&netarm_serial_drv);
-}
-
-__weak struct serial_device *default_serial_console(void)
-{
-	return &netarm_serial_drv;
-}