powerpc/t1024rdb: Add T1024 RDB board support

T1024RDB is a Freescale Reference Design Board that hosts the T1024 SoC.

T1024RDB board Overview
-----------------------
- T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz
- CoreNet fabric supporting coherent and noncoherent transactions with
  prioritization and bandwidth allocation
- 32-/64-bit DDR3L SDRAM memory controller with ECC and interleaving support
- Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC
- Ethernet interfaces:
  - Two 10M/100M/1G RGMII ports on-board
  - one 10Gbps XFI interface
- PCIe: Three PCIe controllers: one PCIe Slot and two Mini-PCIe connectors.
- SerDes: 4 lanes up to 10.3125GHz
- IFC: 128MB NOR Flash, 512MB NAND Flash and CPLD
- eSPI: 64MB N25Q512 SPI flash.
- Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB)
- USB: Two  Type-A USB2.0 ports with internal PHY
- eSDHC: Support SD, SDHC, SDXC and MMC/eMMC
- I2C: Four I2C controllers
- UART: Two UART serial ports

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
[York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT
	   Fix Kconfig by adding SUPPORT_SPL]
Reviewed-by: York Sun <yorksun@freescale.com>

1 files changed, 107 insertions, 0 deletions

diff --git a/board/freescale/t102xrdb/spl.c b/board/freescale/t102xrdb/spl.c
new file mode 100644
index 0000000000..dd2dec4412
--- /dev/null
+++ b/board/freescale/t102xrdb/spl.c
@@ -0,0 +1,107 @@
+/* Copyright 2014 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ */
+
+#include <common.h>
+#include <malloc.h>
+#include <ns16550.h>
+#include <nand.h>
+#include <i2c.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <spi_flash.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+phys_size_t get_effective_memsize(void)
+{
+	return CONFIG_SYS_L3_SIZE;
+}
+
+unsigned long get_board_sys_clk(void)
+{
+	return CONFIG_SYS_CLK_FREQ;
+}
+
+unsigned long get_board_ddr_clk(void)
+{
+	return CONFIG_DDR_CLK_FREQ;
+}
+
+void board_init_f(ulong bootflag)
+{
+	u32 plat_ratio, sys_clk, ccb_clk;
+	ccsr_gur_t *gur = (void *)CONFIG_SYS_MPC85xx_GUTS_ADDR;
+
+	/* Memcpy existing GD at CONFIG_SPL_GD_ADDR */
+	memcpy((void *)CONFIG_SPL_GD_ADDR, (void *)gd, sizeof(gd_t));
+
+	/* Update GD pointer */
+	gd = (gd_t *)(CONFIG_SPL_GD_ADDR);
+
+	console_init_f();
+
+	/* initialize selected port with appropriate baud rate */
+	sys_clk = get_board_sys_clk();
+	plat_ratio = (in_be32(&gur->rcwsr[0]) >> 25) & 0x1f;
+	ccb_clk = sys_clk * plat_ratio / 2;
+
+	NS16550_init((NS16550_t)CONFIG_SYS_NS16550_COM1,
+		     ccb_clk / 16 / CONFIG_BAUDRATE);
+
+#if defined(CONFIG_SPL_MMC_BOOT)
+	puts("\nSD boot...\n");
+#elif defined(CONFIG_SPL_SPI_BOOT)
+	puts("\nSPI boot...\n");
+#elif defined(CONFIG_SPL_NAND_BOOT)
+	puts("\nNAND boot...\n");
+#endif
+
+	relocate_code(CONFIG_SPL_RELOC_STACK, (gd_t *)CONFIG_SPL_GD_ADDR, 0x0);
+}
+
+void board_init_r(gd_t *gd, ulong dest_addr)
+{
+	bd_t *bd;
+
+	bd = (bd_t *)(gd + sizeof(gd_t));
+	memset(bd, 0, sizeof(bd_t));
+	gd->bd = bd;
+	bd->bi_memstart = CONFIG_SYS_INIT_L3_ADDR;
+	bd->bi_memsize = CONFIG_SYS_L3_SIZE;
+
+	probecpu();
+	get_clocks();
+	mem_malloc_init(CONFIG_SPL_RELOC_MALLOC_ADDR,
+			CONFIG_SPL_RELOC_MALLOC_SIZE);
+
+#ifdef CONFIG_SPL_NAND_BOOT
+	nand_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			    (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_initialize(bd);
+	mmc_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			   (uchar *)CONFIG_ENV_ADDR);
+#endif
+#ifdef CONFIG_SPL_SPI_BOOT
+	spi_spl_load_image(CONFIG_ENV_OFFSET, CONFIG_ENV_SIZE,
+			   (uchar *)CONFIG_ENV_ADDR);
+#endif
+
+	gd->env_addr  = (ulong)(CONFIG_ENV_ADDR);
+	gd->env_valid = 1;
+
+	i2c_init_all();
+
+	gd->ram_size = initdram(0);
+
+#ifdef CONFIG_SPL_MMC_BOOT
+	mmc_boot();
+#elif defined(CONFIG_SPL_SPI_BOOT)
+	spi_boot();
+#elif defined(CONFIG_SPL_NAND_BOOT)
+	nand_boot();
+#endif
+}