arm: imx: Add support for GE Bx50v3 boards

Add support for GE B450v3, B650v3 and B850v3 boards. The boards
are based on Advantech BA16 module which has a i.MX6D processor.
The boards support:
 - FEC Ethernet
 - USB Ports
 - SDHC and MMC boot
 - SPI NOR
 - LVDS and HDMI display

Basic information about the module:
 - Module manufacturer: Advantech
 - CPU: Freescale ARM Cortex-A9 i.MX6D
 - SPECS:
     Up to 2GB Onboard DDR3 Memory;
     Up to 16GB Onboard eMMC NAND Flash
     Supports OpenGL ES 2.0 and OpenVG 1.1
     HDMI, 24-bit LVDS
     1x UART, 2x I2C, 8x GPIO,
     4x Host USB 2.0 port, 1x USB OTG port,
     1x micro SD (SDHC),1x SDIO, 1x SATA II,
     1x 10/100/1000 Mbps Ethernet, 1x PCIe X1 Gen2

Signed-off-by: Akshay Bhat <akshay.bhat@timesys.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>

5 files changed, 718 insertions, 0 deletions

diff --git a/board/ge/bx50v3/Kconfig b/board/ge/bx50v3/Kconfig
new file mode 100644
index 0000000000..d50dece18e
--- /dev/null
+++ b/board/ge/bx50v3/Kconfig
@@ -0,0 +1,18 @@
+if TARGET_GE_B450V3 || TARGET_GE_B650V3 || TARGET_GE_B850V3
+
+config IMX_CONFIG
+	default "board/ge/bx50v3/bx50v3.cfg"
+
+config SYS_BOARD
+	default "bx50v3"
+
+config SYS_VENDOR
+	default "ge"
+
+config SYS_SOC
+	default "mx6"
+
+config SYS_CONFIG_NAME
+	default "ge_bx50v3"
+
+endif
diff --git a/board/ge/bx50v3/MAINTAINERS b/board/ge/bx50v3/MAINTAINERS
new file mode 100644
index 0000000000..8e6079197f
--- /dev/null
+++ b/board/ge/bx50v3/MAINTAINERS
@@ -0,0 +1,8 @@
+GE_BX50V3 BOARD
+M:	Martin Donnelly <martin.donnelly@ge.com>
+S:	Maintained
+F:	board/ge/bx50v3/
+F:	include/configs/ge_bx50v3.h
+F:	configs/ge_b450v3_defconfig
+F:	configs/ge_b650v3_defconfig
+F:	configs/ge_b850v3_defconfig
diff --git a/board/ge/bx50v3/Makefile b/board/ge/bx50v3/Makefile
new file mode 100644
index 0000000000..bcd149f5b0
--- /dev/null
+++ b/board/ge/bx50v3/Makefile
@@ -0,0 +1,8 @@
+#
+# Copyright 2015 Timesys Corporation
+# Copyright 2015 General Electric Company
+#
+# SPDX-License-Identifier:	GPL-2.0+
+#
+
+obj-y  := bx50v3.o
diff --git a/board/ge/bx50v3/bx50v3.c b/board/ge/bx50v3/bx50v3.c
new file mode 100644
index 0000000000..70c298d2d0
--- /dev/null
+++ b/board/ge/bx50v3/bx50v3.c
@@ -0,0 +1,533 @@
+/*
+ * Copyright 2015 Timesys Corporation
+ * Copyright 2015 General Electric Company
+ * Copyright 2012 Freescale Semiconductor, Inc.
+ *
+ * SPDX-License-Identifier:	GPL-2.0+
+ */
+
+#include <asm/arch/clock.h>
+#include <asm/arch/imx-regs.h>
+#include <asm/arch/iomux.h>
+#include <asm/arch/mx6-pins.h>
+#include <asm/errno.h>
+#include <asm/gpio.h>
+#include <asm/imx-common/mxc_i2c.h>
+#include <asm/imx-common/iomux-v3.h>
+#include <asm/imx-common/boot_mode.h>
+#include <asm/imx-common/video.h>
+#include <mmc.h>
+#include <fsl_esdhc.h>
+#include <miiphy.h>
+#include <netdev.h>
+#include <asm/arch/mxc_hdmi.h>
+#include <asm/arch/crm_regs.h>
+#include <asm/io.h>
+#include <asm/arch/sys_proto.h>
+#include <i2c.h>
+DECLARE_GLOBAL_DATA_PTR;
+
+#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
+	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
+	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)
+
+#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE |	\
+	PAD_CTL_SPEED_HIGH | PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST)
+
+#define ENET_CLK_PAD_CTRL (PAD_CTL_SPEED_MED | \
+	PAD_CTL_DSE_120ohm | PAD_CTL_SRE_FAST)
+
+#define ENET_RX_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
+	PAD_CTL_SPEED_HIGH   | PAD_CTL_SRE_FAST)
+
+#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
+		      PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
+
+#define I2C_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
+	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |	\
+	PAD_CTL_ODE | PAD_CTL_SRE_FAST)
+
+#define I2C_PAD MUX_PAD_CTRL(I2C_PAD_CTRL)
+
+int dram_init(void)
+{
+	gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);
+
+	return 0;
+}
+
+static iomux_v3_cfg_t const uart3_pads[] = {
+	MX6_PAD_EIM_D31__UART3_RTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D23__UART3_CTS_B | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D24__UART3_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_EIM_D25__UART3_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const uart4_pads[] = {
+	MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+	MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const enet_pads[] = {
+	MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_MDC__ENET_MDC   | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TXC__RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD0__RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD1__RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD2__RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TD3__RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL),
+	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK  | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
+	MX6_PAD_RGMII_RXC__RGMII_RXC | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII_RD0__RGMII_RD0 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII_RD1__RGMII_RD1 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII_RD2__RGMII_RD2 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII_RD3__RGMII_RD3 | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_RX_PAD_CTRL),
+	/* AR8033 PHY Reset */
+	MX6_PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_iomux_enet(void)
+{
+	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
+
+	/* Reset AR8033 PHY */
+	gpio_direction_output(IMX_GPIO_NR(1, 28), 0);
+	udelay(500);
+	gpio_set_value(IMX_GPIO_NR(1, 28), 1);
+}
+
+static iomux_v3_cfg_t const usdhc2_pads[] = {
+	MX6_PAD_SD2_CLK__SD2_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_CMD__SD2_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT0__SD2_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT1__SD2_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT2__SD2_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD2_DAT3__SD2_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_GPIO_4__GPIO1_IO04	| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc3_pads[] = {
+	MX6_PAD_SD3_CLK__SD3_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_CMD__SD3_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_RST__SD3_RESET | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT0__SD3_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT1__SD3_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT2__SD3_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT3__SD3_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT4__SD3_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT5__SD3_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT6__SD3_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD3_DAT7__SD3_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const usdhc4_pads[] = {
+	MX6_PAD_SD4_CLK__SD4_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_CMD__SD4_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT0__SD4_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT1__SD4_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT2__SD4_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT3__SD4_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT4__SD4_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT5__SD4_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT6__SD4_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_SD4_DAT7__SD4_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
+	MX6_PAD_NANDF_CS0__GPIO6_IO11 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_NANDF_CS1__GPIO6_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static iomux_v3_cfg_t const ecspi1_pads[] = {
+	MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
+	MX6_PAD_EIM_EB2__GPIO2_IO30 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static struct i2c_pads_info i2c_pad_info1 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | I2C_PAD,
+		.gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | I2C_PAD,
+		.gp = IMX_GPIO_NR(5, 27)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | I2C_PAD,
+		.gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | I2C_PAD,
+		.gp = IMX_GPIO_NR(5, 26)
+	}
+};
+
+static struct i2c_pads_info i2c_pad_info2 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | I2C_PAD,
+		.gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | I2C_PAD,
+		.gp = IMX_GPIO_NR(4, 12)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | I2C_PAD,
+		.gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | I2C_PAD,
+		.gp = IMX_GPIO_NR(4, 13)
+	}
+};
+
+static struct i2c_pads_info i2c_pad_info3 = {
+	.scl = {
+		.i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | I2C_PAD,
+		.gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | I2C_PAD,
+		.gp = IMX_GPIO_NR(1, 3)
+	},
+	.sda = {
+		.i2c_mode = MX6_PAD_GPIO_6__I2C3_SDA | I2C_PAD,
+		.gpio_mode = MX6_PAD_GPIO_6__GPIO1_IO06 | I2C_PAD,
+		.gp = IMX_GPIO_NR(1, 6)
+	}
+};
+
+#ifdef CONFIG_MXC_SPI
+int board_spi_cs_gpio(unsigned bus, unsigned cs)
+{
+	return (bus == 0 && cs == 0) ? (IMX_GPIO_NR(2, 30)) : -1;
+}
+
+static void setup_spi(void)
+{
+	imx_iomux_v3_setup_multiple_pads(ecspi1_pads, ARRAY_SIZE(ecspi1_pads));
+}
+#endif
+
+static iomux_v3_cfg_t const pcie_pads[] = {
+	MX6_PAD_GPIO_5__GPIO1_IO05 | MUX_PAD_CTRL(NO_PAD_CTRL),
+	MX6_PAD_GPIO_17__GPIO7_IO12 | MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+
+static void setup_pcie(void)
+{
+	imx_iomux_v3_setup_multiple_pads(pcie_pads, ARRAY_SIZE(pcie_pads));
+}
+
+static void setup_iomux_uart(void)
+{
+	imx_iomux_v3_setup_multiple_pads(uart3_pads, ARRAY_SIZE(uart3_pads));
+	imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
+}
+
+#ifdef CONFIG_FSL_ESDHC
+struct fsl_esdhc_cfg usdhc_cfg[3] = {
+	{USDHC2_BASE_ADDR},
+	{USDHC3_BASE_ADDR},
+	{USDHC4_BASE_ADDR},
+};
+
+#define USDHC2_CD_GPIO	IMX_GPIO_NR(1, 4)
+#define USDHC4_CD_GPIO	IMX_GPIO_NR(6, 11)
+
+int board_mmc_getcd(struct mmc *mmc)
+{
+	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
+	int ret = 0;
+
+	switch (cfg->esdhc_base) {
+	case USDHC2_BASE_ADDR:
+		ret = !gpio_get_value(USDHC2_CD_GPIO);
+		break;
+	case USDHC3_BASE_ADDR:
+		ret = 1; /* eMMC is always present */
+		break;
+	case USDHC4_BASE_ADDR:
+		ret = !gpio_get_value(USDHC4_CD_GPIO);
+		break;
+	}
+
+	return ret;
+}
+
+int board_mmc_init(bd_t *bis)
+{
+	int ret;
+	int i;
+
+	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
+		switch (i) {
+		case 0:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc2_pads, ARRAY_SIZE(usdhc2_pads));
+			gpio_direction_input(USDHC2_CD_GPIO);
+			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC2_CLK);
+			break;
+		case 1:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
+			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
+			break;
+		case 2:
+			imx_iomux_v3_setup_multiple_pads(
+				usdhc4_pads, ARRAY_SIZE(usdhc4_pads));
+			gpio_direction_input(USDHC4_CD_GPIO);
+			usdhc_cfg[2].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK);
+			break;
+		default:
+			printf("Warning: you configured more USDHC controllers\n"
+			       "(%d) then supported by the board (%d)\n",
+			       i + 1, CONFIG_SYS_FSL_USDHC_NUM);
+			return -EINVAL;
+		}
+
+		ret = fsl_esdhc_initialize(bis, &usdhc_cfg[i]);
+		if (ret)
+			return ret;
+	}
+
+	return 0;
+}
+#endif
+
+static int mx6_rgmii_rework(struct phy_device *phydev)
+{
+	/* Configure AR8033 to ouput a 125MHz clk from CLK_25M */
+	/* set device address 0x7 */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
+	/* offset 0x8016: CLK_25M Clock Select */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
+	/* enable register write, no post increment, address 0x7 */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);
+	/* set to 125 MHz from local PLL source */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x18);
+
+	/* rgmii tx clock delay enable */
+	/* set debug port address: SerDes Test and System Mode Control */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x05);
+	/* enable rgmii tx clock delay */
+	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x100);
+
+	return 0;
+}
+
+int board_phy_config(struct phy_device *phydev)
+{
+	mx6_rgmii_rework(phydev);
+
+	if (phydev->drv->config)
+		phydev->drv->config(phydev);
+
+	return 0;
+}
+
+#if defined(CONFIG_VIDEO_IPUV3)
+static iomux_v3_cfg_t const backlight_pads[] = {
+	/* Power for LVDS Display */
+	MX6_PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL),
+#define LVDS_POWER_GP IMX_GPIO_NR(3, 22)
+	/* Backlight enable for LVDS display */
+	MX6_PAD_GPIO_0__GPIO1_IO00 | MUX_PAD_CTRL(NO_PAD_CTRL),
+#define LVDS_BACKLIGHT_GP IMX_GPIO_NR(1, 0)
+};
+
+static void do_enable_hdmi(struct display_info_t const *dev)
+{
+	imx_enable_hdmi_phy();
+}
+
+int board_cfb_skip(void)
+{
+	gpio_direction_output(LVDS_POWER_GP, 1);
+
+	return 0;
+}
+
+static int detect_baseboard(struct display_info_t const *dev)
+{
+	if (IS_ENABLED(CONFIG_TARGET_GE_B450V3) ||
+	    IS_ENABLED(CONFIG_TARGET_GE_B650V3))
+		return 1;
+
+	return 0;
+}
+
+struct display_info_t const displays[] = {{
+	.bus	= -1,
+	.addr	= -1,
+	.pixfmt	= IPU_PIX_FMT_RGB24,
+	.detect	= detect_baseboard,
+	.enable	= NULL,
+	.mode	= {
+		.name           = "G121X1-L03",
+		.refresh        = 60,
+		.xres           = 1024,
+		.yres           = 768,
+		.pixclock       = 15385,
+		.left_margin    = 20,
+		.right_margin   = 300,
+		.upper_margin   = 30,
+		.lower_margin   = 8,
+		.hsync_len      = 1,
+		.vsync_len      = 1,
+		.sync           = FB_SYNC_EXT,
+		.vmode          = FB_VMODE_NONINTERLACED
+} }, {
+	.bus	= -1,
+	.addr	= 3,
+	.pixfmt	= IPU_PIX_FMT_RGB24,
+	.detect	= detect_hdmi,
+	.enable	= do_enable_hdmi,
+	.mode	= {
+		.name           = "HDMI",
+		.refresh        = 60,
+		.xres           = 1024,
+		.yres           = 768,
+		.pixclock       = 15385,
+		.left_margin    = 220,
+		.right_margin   = 40,
+		.upper_margin   = 21,
+		.lower_margin   = 7,
+		.hsync_len      = 60,
+		.vsync_len      = 10,
+		.sync           = FB_SYNC_EXT,
+		.vmode          = FB_VMODE_NONINTERLACED
+} } };
+size_t display_count = ARRAY_SIZE(displays);
+
+static void setup_display(void)
+{
+	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
+	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
+	int reg;
+
+	enable_ipu_clock();
+	imx_setup_hdmi();
+
+	reg = readl(&mxc_ccm->CCGR3);
+	reg |=  MXC_CCM_CCGR3_LDB_DI0_MASK;
+	writel(reg, &mxc_ccm->CCGR3);
+
+	reg = readl(&mxc_ccm->cs2cdr);
+	reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK |
+		 MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
+	reg |= (3 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) |
+	       (3 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
+	writel(reg, &mxc_ccm->cs2cdr);
+
+	reg = readl(&mxc_ccm->cscmr2);
+	reg |= (MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV);
+	writel(reg, &mxc_ccm->cscmr2);
+
+	reg = readl(&mxc_ccm->chsccdr);
+	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
+		<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
+	writel(reg, &mxc_ccm->chsccdr);
+
+	reg = IOMUXC_GPR2_BGREF_RRMODE_EXTERNAL_RES
+	     | IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_HIGH
+	     | IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW
+	     | IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG
+	     | IOMUXC_GPR2_DATA_WIDTH_CH1_24BIT
+	     | IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG
+	     | IOMUXC_GPR2_DATA_WIDTH_CH0_24BIT
+	     | IOMUXC_GPR2_LVDS_CH1_MODE_ENABLED_DI0
+	     | IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0;
+	writel(reg, &iomux->gpr[2]);
+
+	reg = readl(&iomux->gpr[3]);
+	reg = (reg & ~(IOMUXC_GPR3_LVDS0_MUX_CTL_MASK |
+		       IOMUXC_GPR3_LVDS1_MUX_CTL_MASK |
+		       IOMUXC_GPR3_HDMI_MUX_CTL_MASK))
+	    | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
+	       << IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET)
+	    | (IOMUXC_GPR3_MUX_SRC_IPU1_DI0
+	       << IOMUXC_GPR3_LVDS1_MUX_CTL_OFFSET);
+	writel(reg, &iomux->gpr[3]);
+
+	/* backlights off until needed */
+	imx_iomux_v3_setup_multiple_pads(backlight_pads,
+					 ARRAY_SIZE(backlight_pads));
+	gpio_direction_input(LVDS_POWER_GP);
+	gpio_direction_input(LVDS_BACKLIGHT_GP);
+}
+#endif /* CONFIG_VIDEO_IPUV3 */
+
+/*
+ * Do not overwrite the console
+ * Use always serial for U-Boot console
+ */
+int overwrite_console(void)
+{
+	return 1;
+}
+
+int board_eth_init(bd_t *bis)
+{
+	setup_iomux_enet();
+	setup_pcie();
+
+	return cpu_eth_init(bis);
+}
+
+static iomux_v3_cfg_t const misc_pads[] = {
+	MX6_PAD_KEY_ROW2__GPIO4_IO11	| MUX_PAD_CTRL(NO_PAD_CTRL),
+};
+#define SUS_S3_OUT	IMX_GPIO_NR(4, 11)
+#define WIFI_EN	IMX_GPIO_NR(6, 14)
+
+int board_early_init_f(void)
+{
+	imx_iomux_v3_setup_multiple_pads(misc_pads,
+					 ARRAY_SIZE(misc_pads));
+
+	setup_iomux_uart();
+
+
+	return 0;
+}
+
+int board_init(void)
+{
+	gpio_direction_output(SUS_S3_OUT, 1);
+	gpio_direction_output(WIFI_EN, 1);
+#if defined(CONFIG_VIDEO_IPUV3)
+	setup_display();
+#endif
+	/* address of boot parameters */
+	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
+
+#ifdef CONFIG_MXC_SPI
+	setup_spi();
+#endif
+	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
+	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
+	setup_i2c(3, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info3);
+
+	return 0;
+}
+
+#ifdef CONFIG_CMD_BMODE
+static const struct boot_mode board_boot_modes[] = {
+	/* 4 bit bus width */
+	{"sd2",	 MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)},
+	{"sd3",	 MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
+	{NULL,	 0},
+};
+#endif
+
+int board_late_init(void)
+{
+#ifdef CONFIG_CMD_BMODE
+	add_board_boot_modes(board_boot_modes);
+#endif
+	/* We need at least 200ms between power on and backlight on
+	 * as per specifications from CHI MEI */
+	mdelay(250);
+
+	/* Backlight Power */
+	gpio_direction_output(LVDS_BACKLIGHT_GP, 1);
+
+	return 0;
+}
+
+int checkboard(void)
+{
+	printf("BOARD: %s\n", CONFIG_BOARD_NAME);
+	return 0;
+}
diff --git a/board/ge/bx50v3/bx50v3.cfg b/board/ge/bx50v3/bx50v3.cfg
new file mode 100644
index 0000000000..de88769067
--- /dev/null
+++ b/board/ge/bx50v3/bx50v3.cfg
@@ -0,0 +1,151 @@
+/*
+ *
+ * Copyright 2015 Timesys Corporation.
+ * Copyright 2015 General Electric Company
+ *
+ * SPDX-License-Identifier:    GPL-2.0+
+ *
+ * Refer doc/README.imximage for more details about how-to configure
+ * and create imximage boot image
+ *
+ * The syntax is taken as close as possible with the kwbimage
+ */
+
+IMAGE_VERSION 2
+BOOT_FROM sd
+
+#define __ASSEMBLY__
+#include <config.h>
+#include "asm/arch/mx6-ddr.h"
+#include "asm/arch/iomux.h"
+#include "asm/arch/crm_regs.h"
+
+/* DDR IO */
+DATA 4, MX6_IOM_GRP_DDR_TYPE,	0x000c0000
+DATA 4, MX6_IOM_GRP_DDRPKE,	0x00000000
+DATA 4, MX6_IOM_DRAM_SDCLK_0,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDCLK_1,	0x00000030
+DATA 4, MX6_IOM_DRAM_CAS,	0x00000030
+DATA 4, MX6_IOM_DRAM_RAS,	0x00000030
+DATA 4, MX6_IOM_GRP_ADDDS,	0x00000030
+DATA 4, MX6_IOM_DRAM_RESET,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDBA2,	0x00000000
+DATA 4, MX6_IOM_DRAM_SDODT0,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDODT1,	0x00000030
+DATA 4, MX6_IOM_GRP_CTLDS,	0x00000030
+DATA 4, MX6_IOM_DDRMODE_CTL,	0x00020000
+DATA 4, MX6_IOM_DRAM_SDQS0,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS1,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS2,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS3,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS4,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS5,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS6,	0x00000030
+DATA 4, MX6_IOM_DRAM_SDQS7,	0x00000030
+DATA 4, MX6_IOM_GRP_DDRMODE,	0x00020000
+DATA 4, MX6_IOM_GRP_B0DS,	0x00000030
+DATA 4, MX6_IOM_GRP_B1DS,	0x00000030
+DATA 4, MX6_IOM_GRP_B2DS,	0x00000030
+DATA 4, MX6_IOM_GRP_B3DS,	0x00000030
+DATA 4, MX6_IOM_GRP_B4DS,	0x00000030
+DATA 4, MX6_IOM_GRP_B5DS,	0x00000030
+DATA 4, MX6_IOM_GRP_B6DS,	0x00000030
+DATA 4, MX6_IOM_GRP_B7DS,	0x00000030
+DATA 4, MX6_IOM_DRAM_DQM0,	0x00000030
+DATA 4, MX6_IOM_DRAM_DQM1,	0x00000030
+DATA 4, MX6_IOM_DRAM_DQM2,	0x00000030
+DATA 4, MX6_IOM_DRAM_DQM3,	0x00000030
+DATA 4, MX6_IOM_DRAM_DQM4,	0x00000030
+DATA 4, MX6_IOM_DRAM_DQM5,	0x00000030
+DATA 4, MX6_IOM_DRAM_DQM6,	0x00000030
+DATA 4, MX6_IOM_DRAM_DQM7,	0x00000030
+
+/* Calibrations */
+/* ZQ */
+DATA 4, MX6_MMDC_P0_MPZQHWCTRL,  0xa1390003
+/* write leveling */
+DATA 4, MX6_MMDC_P0_MPWLDECTRL0, 0x001F001F
+DATA 4, MX6_MMDC_P0_MPWLDECTRL1, 0x001F001F
+DATA 4, MX6_MMDC_P1_MPWLDECTRL0, 0x001F001F
+DATA 4, MX6_MMDC_P1_MPWLDECTRL1, 0x001F001F
+/* Read DQS Gating calibration */
+DATA 4, MX6_MMDC_P0_MPDGCTRL0,	0x45380544
+DATA 4, MX6_MMDC_P0_MPDGCTRL1,	0x05280530
+DATA 4, MX6_MMDC_P1_MPDGCTRL0,	0x4530053C
+DATA 4, MX6_MMDC_P1_MPDGCTRL1,	0x0530050C
+/* Read calibration */
+DATA 4, MX6_MMDC_P0_MPRDDLCTL,	0x36303032
+DATA 4, MX6_MMDC_P1_MPRDDLCTL,	0x38363042
+/* Write calibration */
+DATA 4, MX6_MMDC_P0_MPWRDLCTL,	0x3A3A423E
+DATA 4, MX6_MMDC_P1_MPWRDLCTL,	0x4A38483E
+/* read data bit delay */
+DATA 4, MX6_MMDC_P0_MPRDDQBY0DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY1DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY2DL, 0x33333333
+DATA 4, MX6_MMDC_P0_MPRDDQBY3DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY0DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY1DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY2DL, 0x33333333
+DATA 4, MX6_MMDC_P1_MPRDDQBY3DL, 0x33333333
+
+/* Complete calibration by forced measurment */
+DATA 4, MX6_MMDC_P0_MPMUR0,	0x00000800
+DATA 4, MX6_MMDC_P1_MPMUR0,	0x00000800
+
+/* MMDC init */
+DATA 4, MX6_MMDC_P0_MDPDC,	0x00020036
+DATA 4, MX6_MMDC_P0_MDOTC,	0x09444040
+DATA 4, MX6_MMDC_P0_MDCFG0,	0x8A8F79A4
+DATA 4, MX6_MMDC_P0_MDCFG1,	0xDB538E64
+DATA 4, MX6_MMDC_P0_MDCFG2,	0x01ff00db
+DATA 4, MX6_MMDC_P0_MDMISC,	0x00001740
+DATA 4, MX6_MMDC_P0_MDSCR,	0x00008000
+DATA 4, MX6_MMDC_P0_MDRWD,	0x000026d2
+DATA 4, MX6_MMDC_P0_MDOR,	0x008F1023
+DATA 4, MX6_MMDC_P0_MDASP,	0x00000047
+DATA 4, MX6_MMDC_P0_MDCTL,	0x841a0000
+
+/* Initialize Micron MT41J128M */
+DATA 4, MX6_MMDC_P0_MDSCR,	0x04088032
+DATA 4, MX6_MMDC_P0_MDSCR,	0x0408803a
+DATA 4, MX6_MMDC_P0_MDSCR,	0x00008033
+DATA 4, MX6_MMDC_P0_MDSCR,	0x0000803b
+DATA 4, MX6_MMDC_P0_MDSCR,	0x00408031
+DATA 4, MX6_MMDC_P0_MDSCR,	0x00408039
+DATA 4, MX6_MMDC_P0_MDSCR,	0x09408030
+DATA 4, MX6_MMDC_P0_MDSCR,	0x09408038
+DATA 4, MX6_MMDC_P0_MDSCR,	0x04008040
+DATA 4, MX6_MMDC_P0_MDSCR,	0x04008048
+DATA 4, MX6_MMDC_P0_MDREF,	0x00005800
+DATA 4, MX6_MMDC_P0_MPODTCTRL,	0x00011117
+DATA 4, MX6_MMDC_P1_MPODTCTRL,	0x00011117
+DATA 4, MX6_MMDC_P0_MDPDC,	0x00025576
+DATA 4, MX6_MMDC_P0_MAPSR,	0x00011006
+DATA 4, MX6_MMDC_P0_MDSCR,	0x00000000
+
+/* set the default clock gate to save power */
+DATA 4, CCM_CCGR0, 0x00C03F3F
+DATA 4, CCM_CCGR1, 0x0030FC03
+DATA 4, CCM_CCGR2, 0x0FFFC000
+DATA 4, CCM_CCGR3, 0x3FF00000
+DATA 4, CCM_CCGR4, 0x00FFF300
+DATA 4, CCM_CCGR5, 0x0F0000C3
+DATA 4, CCM_CCGR6, 0x000003FF
+
+/* enable AXI cache for VDOA/VPU/IPU */
+DATA 4, MX6_IOMUXC_GPR4, 0xF00000CF
+/* set IPU AXI-id0 Qos=0xf(bypass) AXI-id1 Qos=0x7 */
+DATA 4, MX6_IOMUXC_GPR6, 0x007F007F
+DATA 4, MX6_IOMUXC_GPR7, 0x007F007F
+
+/*
+ * Setup CCM_CCOSR register as follows:
+ *
+ * cko1_en  1	   --> CKO1 enabled
+ * cko1_div 111  --> divide by 8
+ * cko1_sel 1011 --> ahb_clk_root
+ *
+ * This sets CKO1 at ahb_clk_root/8 132/8 16.5 MHz
+ */
+DATA 4, CCM_CCOSR, 0x000000fb