diff options
| -rw-r--r-- | arch/arm/dts/sun8i-r40-bananapi-m2-ultra.dts | 168 | ||||
| -rw-r--r-- | arch/arm/dts/sun8i-r40.dtsi | 303 | ||||
| -rw-r--r-- | arch/arm/dts/sun8i-v40-bananapi-m2-berry.dts | 50 |
3 files changed, 486 insertions, 35 deletions
diff --git a/arch/arm/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/dts/sun8i-r40-bananapi-m2-ultra.dts index 28c9158302..25fb048c7d 100644 --- a/arch/arm/dts/sun8i-r40-bananapi-m2-ultra.dts +++ b/arch/arm/dts/sun8i-r40-bananapi-m2-ultra.dts @@ -1,5 +1,6 @@ /* - * Copyright (C) 2016 Chen-Yu Tsai <wens@csie.org> + * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org> + * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io> * * This file is dual-licensed: you can use it either under the terms * of the GPL or the X11 license, at your option. Note that this dual @@ -43,6 +44,8 @@ /dts-v1/; #include "sun8i-r40.dtsi" +#include <dt-bindings/gpio/gpio.h> + / { model = "Banana Pi BPI-M2-Ultra"; compatible = "sinovoip,bpi-m2-ultra", "allwinner,sun8i-r40"; @@ -55,17 +58,47 @@ chosen { stdout-path = "serial0:115200n8"; }; + + leds { + compatible = "gpio-leds"; + + pwr-led { + label = "bananapi:red:pwr"; + gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + user-led-green { + label = "bananapi:green:user"; + gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; + }; + + user-led-blue { + label = "bananapi:blue:user"; + gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>; + }; + }; + + reg_vcc5v0: vcc5v0 { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>; /* PH23 */ + enable-active-high; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */ + }; }; -&i2c0 { - pinctrl-names = "default"; - pinctrl-0 = <&i2c0_pins>; +&ehci1 { status = "okay"; }; -&uart0 { - pinctrl-names = "default"; - pinctrl-0 = <&uart0_pb_pins>; +&ehci2 { status = "okay"; }; @@ -74,6 +107,7 @@ pinctrl-0 = <&gmac_rgmii_pins>; phy-handle = <&phy1>; phy-mode = "rgmii"; + phy-supply = <®_dc1sw>; status = "okay"; }; @@ -83,3 +117,123 @@ reg = <1>; }; }; + +&i2c0 { + status = "okay"; + + axp22x: pmic@34 { + compatible = "x-powers,axp221"; + reg = <0x34>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + }; +}; + +#include "axp22x.dtsi" + +&mmc0 { + vmmc-supply = <®_dcdc1>; + bus-width = <4>; + cd-gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */ + cd-inverted; + status = "okay"; +}; + +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pg_pins>; + vmmc-supply = <®_dldo2>; + vqmmc-supply = <®_dldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + +&mmc2 { + vmmc-supply = <®_dcdc1>; + vqmmc-supply = <®_dcdc1>; + bus-width = <8>; + non-removable; + status = "okay"; +}; + +&ohci1 { + status = "okay"; +}; + +&ohci2 { + status = "okay"; +}; + +®_aldo2 { + regulator-always-on; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + regulator-name = "vcc-pa"; +}; + +®_aldo3 { + regulator-always-on; + regulator-min-microvolt = <2700000>; + regulator-max-microvolt = <3300000>; + regulator-name = "avcc"; +}; + +®_dc1sw { + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-gmac-phy"; +}; + +®_dcdc1 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "vcc-3v0"; +}; + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd-sys"; +}; + +®_dcdc5 { + regulator-always-on; + regulator-min-microvolt = <1500000>; + regulator-max-microvolt = <1500000>; + regulator-name = "vcc-dram"; +}; + +®_dldo1 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi-io"; +}; + +®_dldo2 { + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-name = "vcc-wifi"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pb_pins>; + status = "okay"; +}; + +&usbphy { + usb1_vbus-supply = <®_vcc5v0>; + usb2_vbus-supply = <®_vcc5v0>; + status = "okay"; +}; diff --git a/arch/arm/dts/sun8i-r40.dtsi b/arch/arm/dts/sun8i-r40.dtsi index 2cdfb54282..bd97ca3dc2 100644 --- a/arch/arm/dts/sun8i-r40.dtsi +++ b/arch/arm/dts/sun8i-r40.dtsi @@ -1,7 +1,6 @@ /* - * Copyright 2016 Chen-Yu Tsai - * - * Chen-Yu Tsai <wens@csie.org> + * Copyright 2017 Chen-Yu Tsai <wens@csie.org> + * Copyright 2017 Icenowy Zheng <icenowy@aosc.io> * * This file is dual-licensed: you can use it either under the terms * of the GPL or the X11 license, at your option. Note that this dual @@ -51,24 +50,19 @@ #size-cells = <1>; interrupt-parent = <&gic>; - aliases { - }; - - chosen { - }; - clocks { #address-cells = <1>; #size-cells = <1>; ranges; - osc24M: osc24M_clk { + osc24M: osc24M { #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <24000000>; + clock-output-names = "osc24M"; }; - osc32k: osc32k_clk { + osc32k: osc32k { #clock-cells = <0>; compatible = "fixed-clock"; clock-frequency = <32768>; @@ -80,7 +74,7 @@ #address-cells = <1>; #size-cells = <0>; - cpu0: cpu@0 { + cpu@0 { compatible = "arm,cortex-a7"; device_type = "cpu"; reg = <0>; @@ -105,11 +99,6 @@ }; }; - memory@40000000 { - device_type = "memory"; - reg = <0x40000000 0x80000000>; - }; - soc { compatible = "simple-bus"; #address-cells = <1>; @@ -140,6 +129,122 @@ #size-cells = <0>; }; + mmc1: mmc@1c10000 { + compatible = "allwinner,sun8i-r40-mmc", + "allwinner,sun50i-a64-mmc"; + reg = <0x01c10000 0x1000>; + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC1>; + reset-names = "ahb"; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc2: mmc@1c11000 { + compatible = "allwinner,sun8i-r40-emmc", + "allwinner,sun50i-a64-emmc"; + reg = <0x01c11000 0x1000>; + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC2>; + reset-names = "ahb"; + pinctrl-0 = <&mmc2_pins>; + pinctrl-names = "default"; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + mmc3: mmc@1c12000 { + compatible = "allwinner,sun8i-r40-mmc", + "allwinner,sun50i-a64-mmc"; + reg = <0x01c12000 0x1000>; + clocks = <&ccu CLK_BUS_MMC3>, <&ccu CLK_MMC3>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC3>; + reset-names = "ahb"; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + usbphy: phy@1c13400 { + compatible = "allwinner,sun8i-r40-usb-phy"; + reg = <0x01c13400 0x14>, + <0x01c14800 0x4>, + <0x01c19800 0x4>, + <0x01c1c800 0x4>; + reg-names = "phy_ctrl", + "pmu0", + "pmu1", + "pmu2"; + clocks = <&ccu CLK_USB_PHY0>, + <&ccu CLK_USB_PHY1>, + <&ccu CLK_USB_PHY2>; + clock-names = "usb0_phy", + "usb1_phy", + "usb2_phy"; + resets = <&ccu RST_USB_PHY0>, + <&ccu RST_USB_PHY1>, + <&ccu RST_USB_PHY2>; + reset-names = "usb0_reset", + "usb1_reset", + "usb2_reset"; + status = "disabled"; + #phy-cells = <1>; + }; + + ehci1: usb@1c19000 { + compatible = "allwinner,sun8i-r40-ehci", "generic-ehci"; + reg = <0x01c19000 0x100>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_EHCI1>; + resets = <&ccu RST_BUS_EHCI1>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + ohci1: usb@1c19400 { + compatible = "allwinner,sun8i-r40-ohci", "generic-ohci"; + reg = <0x01c19400 0x100>; + interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_OHCI1>, + <&ccu CLK_USB_OHCI1>; + resets = <&ccu RST_BUS_OHCI1>; + phys = <&usbphy 1>; + phy-names = "usb"; + status = "disabled"; + }; + + ehci2: usb@1c1c000 { + compatible = "allwinner,sun8i-r40-ehci", "generic-ehci"; + reg = <0x01c1c000 0x100>; + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_EHCI2>; + resets = <&ccu RST_BUS_EHCI2>; + phys = <&usbphy 2>; + phy-names = "usb"; + status = "disabled"; + }; + + ohci2: usb@1c1c400 { + compatible = "allwinner,sun8i-r40-ohci", "generic-ohci"; + reg = <0x01c1c400 0x100>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_OHCI2>, + <&ccu CLK_USB_OHCI2>; + resets = <&ccu RST_BUS_OHCI2>; + phys = <&usbphy 2>; + phy-names = "usb"; + status = "disabled"; + }; + ccu: clock@1c20000 { compatible = "allwinner,sun8i-r40-ccu"; reg = <0x01c20000 0x400>; @@ -153,8 +258,7 @@ compatible = "allwinner,sun8i-r40-pinctrl"; reg = <0x01c20800 0x400>; interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; - /* apb should be replaced once CCU is implemented */ - clocks = <&osc24M>, <&osc24M>, <&osc32k>; + clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>; clock-names = "apb", "hosc", "losc"; gpio-controller; interrupt-controller; @@ -174,10 +278,9 @@ drive-strength = <40>; }; - i2c0_pins: i2c0_pins { + i2c0_pins: i2c0-pins { pins = "PB0", "PB1"; function = "i2c0"; - bias-pull-up; }; mmc0_pins: mmc0-pins { @@ -188,20 +291,119 @@ bias-pull-up; }; - uart0_pb_pins: uart0_pb_pins { + mmc1_pg_pins: mmc1-pg-pins { + pins = "PG0", "PG1", "PG2", + "PG3", "PG4", "PG5"; + function = "mmc1"; + drive-strength = <30>; + bias-pull-up; + }; + + mmc2_pins: mmc2-pins { + pins = "PC5", "PC6", "PC7", "PC8", "PC9", + "PC10", "PC11", "PC12", "PC13", "PC14", + "PC15", "PC24"; + function = "mmc2"; + drive-strength = <30>; + bias-pull-up; + }; + + uart0_pb_pins: uart0-pb-pins { pins = "PB22", "PB23"; function = "uart0"; - bias-pull-up; }; }; + wdt: watchdog@1c20c90 { + compatible = "allwinner,sun4i-a10-wdt"; + reg = <0x01c20c90 0x10>; + }; + uart0: serial@1c28000 { compatible = "snps,dw-apb-uart"; reg = <0x01c28000 0x400>; interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; reg-shift = <2>; reg-io-width = <4>; - clocks = <&osc24M>; + clocks = <&ccu CLK_BUS_UART0>; + resets = <&ccu RST_BUS_UART0>; + status = "disabled"; + }; + + uart1: serial@1c28400 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28400 0x400>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART1>; + resets = <&ccu RST_BUS_UART1>; + status = "disabled"; + }; + + uart2: serial@1c28800 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28800 0x400>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART2>; + resets = <&ccu RST_BUS_UART2>; + status = "disabled"; + }; + + uart3: serial@1c28c00 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c28c00 0x400>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART3>; + resets = <&ccu RST_BUS_UART3>; + status = "disabled"; + }; + + uart4: serial@1c29000 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c29000 0x400>; + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART4>; + resets = <&ccu RST_BUS_UART4>; + status = "disabled"; + }; + + uart5: serial@1c29400 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c29400 0x400>; + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART5>; + resets = <&ccu RST_BUS_UART5>; + status = "disabled"; + }; + + uart6: serial@1c29800 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c29800 0x400>; + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART6>; + resets = <&ccu RST_BUS_UART6>; + status = "disabled"; + }; + + uart7: serial@1c29c00 { + compatible = "snps,dw-apb-uart"; + reg = <0x01c29c00 0x400>; + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART7>; + resets = <&ccu RST_BUS_UART7>; status = "disabled"; }; @@ -209,7 +411,54 @@ compatible = "allwinner,sun6i-a31-i2c"; reg = <0x01c2ac00 0x400>; interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&osc24M>; + clocks = <&ccu CLK_BUS_I2C0>; + resets = <&ccu RST_BUS_I2C0>; + pinctrl-0 = <&i2c0_pins>; + pinctrl-names = "default"; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c1: i2c@1c2b000 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b000 0x400>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C1>; + resets = <&ccu RST_BUS_I2C1>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c2: i2c@1c2b400 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b400 0x400>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C2>; + resets = <&ccu RST_BUS_I2C2>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c3: i2c@1c2b800 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2b800 0x400>; + interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C3>; + resets = <&ccu RST_BUS_I2C3>; + status = "disabled"; + #address-cells = <1>; + #size-cells = <0>; + }; + + i2c4: i2c@1c2c000 { + compatible = "allwinner,sun6i-a31-i2c"; + reg = <0x01c2c000 0x400>; + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&ccu CLK_BUS_I2C4>; + resets = <&ccu RST_BUS_I2C4>; status = "disabled"; #address-cells = <1>; #size-cells = <0>; @@ -237,7 +486,7 @@ }; gic: interrupt-controller@1c81000 { - compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic"; + compatible = "arm,gic-400"; reg = <0x01c81000 0x1000>, <0x01c82000 0x1000>, <0x01c84000 0x2000>, @@ -254,7 +503,5 @@ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; - clock-frequency = <24000000>; - arm,cpu-registers-not-fw-configured; }; }; diff --git a/arch/arm/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/dts/sun8i-v40-bananapi-m2-berry.dts index 193d9b29ec..35859d8f32 100644 --- a/arch/arm/dts/sun8i-v40-bananapi-m2-berry.dts +++ b/arch/arm/dts/sun8i-v40-bananapi-m2-berry.dts @@ -56,6 +56,40 @@ chosen { stdout-path = "serial0:115200n8"; }; + + leds { + compatible = "gpio-leds"; + + pwr-led { + label = "bananapi:red:pwr"; + gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + + user-led { + label = "bananapi:green:user"; + gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>; + }; + }; + + reg_vcc5v0: vcc5v0 { + compatible = "regulator-fixed"; + regulator-name = "vcc5v0"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&pio 7 23 GPIO_ACTIVE_HIGH>; /* PH23 */ + enable-active-high; + }; + + wifi_pwrseq: wifi_pwrseq { + compatible = "mmc-pwrseq-simple"; + reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */ + }; +}; + +&ehci1 { + /* Terminus Tech FE 1.1s 4-port USB 2.0 hub here */ + status = "okay"; }; &i2c0 { @@ -125,8 +159,24 @@ status = "okay"; }; +&mmc1 { + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pg_pins>; + vmmc-supply = <®_dldo2>; + vqmmc-supply = <®_dldo1>; + mmc-pwrseq = <&wifi_pwrseq>; + bus-width = <4>; + non-removable; + status = "okay"; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pb_pins>; status = "okay"; }; + +&usbphy { + usb1_vbus-supply = <®_vcc5v0>; + status = "okay"; +}; |