diff options
26 files changed, 757 insertions, 185 deletions
diff --git a/MAINTAINERS b/MAINTAINERS index 1614b913bd..e131f80534 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -663,6 +663,7 @@ Fabio Estevam <fabio.estevam@freescale.com> mx53smd i.MX53 mx6qsabresd i.MX6Q mx6qsabreauto i.MX6Q + wandboard i.MX6DL/S Daniel Gorsulowski <daniel.gorsulowski@esd.eu> diff --git a/arch/arm/cpu/arm926ejs/mxs/spl_mem_init.c b/arch/arm/cpu/arm926ejs/mxs/spl_mem_init.c index fdac73cfaa..bc2d69c857 100644 --- a/arch/arm/cpu/arm926ejs/mxs/spl_mem_init.c +++ b/arch/arm/cpu/arm926ejs/mxs/spl_mem_init.c @@ -46,17 +46,17 @@ static uint32_t dram_vals[] = { 0x00000000, 0x00000000, 0x00010101, 0x01010101, 0x000f0f01, 0x0f02020a, 0x00000000, 0x00010101, 0x00000100, 0x00000100, 0x00000000, 0x00000002, - 0x01010000, 0x05060302, 0x06005003, 0x0a0000c8, - 0x02009c40, 0x0000030c, 0x0036a609, 0x031a0612, + 0x01010000, 0x07080403, 0x06005003, 0x0a0000c8, + 0x02009c40, 0x0002030c, 0x0036a609, 0x031a0612, 0x02030202, 0x00c8001c, 0x00000000, 0x00000000, 0x00012100, 0xffff0303, 0x00012100, 0xffff0303, 0x00012100, 0xffff0303, 0x00012100, 0xffff0303, 0x00000003, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000612, 0x01000F02, - 0x06120612, 0x00000200, 0x00020007, 0xf5014b27, - 0xf5014b27, 0xf5014b27, 0xf5014b27, 0x07000300, - 0x07000300, 0x07000300, 0x07000300, 0x00000006, + 0x06120612, 0x00000200, 0x00020007, 0xf4004a27, + 0xf4004a27, 0xf4004a27, 0xf4004a27, 0x07000300, + 0x07000300, 0x07400300, 0x07400300, 0x00000005, 0x00000000, 0x00000000, 0x01000000, 0x01020408, 0x08040201, 0x000f1133, 0x00000000, 0x00001f04, 0x00001f04, 0x00001f04, 0x00001f04, 0x00001f04, @@ -77,14 +77,14 @@ static uint32_t dram_vals[] = { 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000, - 0x00000000, 0x00000000, 0x00010000, 0x00020304, - 0x00000004, 0x00000000, 0x00000000, 0x00000000, + 0x00000000, 0x00000000, 0x00010000, 0x00030404, + 0x00000003, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x00000000, 0x01010000, 0x01000000, 0x03030000, 0x00010303, 0x01020202, 0x00000000, 0x02040303, 0x21002103, 0x00061200, - 0x06120612, 0x04320432, 0x04320432, 0x00040004, + 0x06120612, 0x04420442, 0x04420442, 0x00040004, 0x00040004, 0x00000000, 0x00000000, 0x00000000, - 0x00000000, 0x00010001 + 0x00000000, 0xffffffff /* * i.MX23 DDR at 133MHz diff --git a/arch/arm/cpu/armv7/mx6/soc.c b/arch/arm/cpu/armv7/mx6/soc.c index 193ba1240f..2ea8ca3bd3 100644 --- a/arch/arm/cpu/armv7/mx6/soc.c +++ b/arch/arm/cpu/armv7/mx6/soc.c @@ -61,6 +61,18 @@ u32 get_cpu_rev(void) return (type << 12) | (reg + 0x10); } +#ifdef CONFIG_REVISION_TAG +u32 __weak get_board_rev(void) +{ + u32 cpurev = get_cpu_rev(); + u32 type = ((cpurev >> 12) & 0xff); + if (type == MXC_CPU_MX6SOLO) + cpurev = (MXC_CPU_MX6DL) << 12 | (cpurev & 0xFFF); + + return cpurev; +} +#endif + void init_aips(void) { struct aipstz_regs *aips1, *aips2; diff --git a/arch/arm/imx-common/Makefile b/arch/arm/imx-common/Makefile index 6309fcdfe6..428a57e1cb 100644 --- a/arch/arm/imx-common/Makefile +++ b/arch/arm/imx-common/Makefile @@ -32,6 +32,7 @@ COBJS-y = iomux-v3.o timer.o cpu.o speed.o COBJS-$(CONFIG_I2C_MXC) += i2c-mxv7.o endif COBJS-$(CONFIG_CMD_BMODE) += cmd_bmode.o +COBJS-$(CONFIG_CMD_HDMIDETECT) += cmd_hdmidet.o COBJS := $(sort $(COBJS-y)) SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c) diff --git a/arch/arm/imx-common/cmd_hdmidet.c b/arch/arm/imx-common/cmd_hdmidet.c new file mode 100644 index 0000000000..794bf50cb6 --- /dev/null +++ b/arch/arm/imx-common/cmd_hdmidet.c @@ -0,0 +1,37 @@ +/* + * Copyright (C) 2012 Boundary Devices Inc. + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ +#include <common.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/mxc_hdmi.h> +#include <asm/io.h> + +static int do_hdmidet(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[]) +{ + struct hdmi_regs *hdmi = (struct hdmi_regs *)HDMI_ARB_BASE_ADDR; + u8 reg = readb(&hdmi->phy_stat0) & HDMI_PHY_HPD; + return (reg&HDMI_PHY_HPD) ? 0 : 1; +} + +U_BOOT_CMD(hdmidet, 1, 1, do_hdmidet, + "detect HDMI monitor", + "" +); diff --git a/arch/arm/imx-common/timer.c b/arch/arm/imx-common/timer.c index ab37d641ec..1dbc413d46 100644 --- a/arch/arm/imx-common/timer.c +++ b/arch/arm/imx-common/timer.c @@ -48,9 +48,6 @@ static struct mxc_gpt *cur_gpt = (struct mxc_gpt *)GPT1_BASE_ADDR; DECLARE_GLOBAL_DATA_PTR; -#define timestamp (gd->arch.tbl) -#define lastinc (gd->arch.lastinc) - static inline unsigned long long tick_to_time(unsigned long long tick) { tick *= CONFIG_SYS_HZ; @@ -70,7 +67,6 @@ static inline unsigned long long us_to_tick(unsigned long long usec) int timer_init(void) { int i; - ulong val; /* setup GP Timer 1 */ __raw_writel(GPTCR_SWR, &cur_gpt->control); @@ -85,9 +81,8 @@ int timer_init(void) i = __raw_readl(&cur_gpt->control); __raw_writel(i | GPTCR_CLKSOURCE_32 | GPTCR_TEN, &cur_gpt->control); - val = __raw_readl(&cur_gpt->counter); - lastinc = val / (MXC_CLK32 / CONFIG_SYS_HZ); - timestamp = 0; + gd->arch.tbl = __raw_readl(&cur_gpt->counter); + gd->arch.tbu = 0; return 0; } @@ -96,18 +91,11 @@ unsigned long long get_ticks(void) { ulong now = __raw_readl(&cur_gpt->counter); /* current tick value */ - if (now >= lastinc) { - /* - * normal mode (non roll) - * move stamp forward with absolut diff ticks - */ - timestamp += (now - lastinc); - } else { - /* we have rollover of incrementer */ - timestamp += (0xFFFFFFFF - lastinc) + now; - } - lastinc = now; - return timestamp; + /* increment tbu if tbl has rolled over */ + if (now < gd->arch.tbl) + gd->arch.tbu++; + gd->arch.tbl = now; + return (((unsigned long long)gd->arch.tbu) << 32) | gd->arch.tbl; } ulong get_timer_masked(void) diff --git a/arch/arm/include/asm/arch-mx6/mx6dl_pins.h b/arch/arm/include/asm/arch-mx6/mx6dl_pins.h index 9494e4126a..9846f1bcb5 100644 --- a/arch/arm/include/asm/arch-mx6/mx6dl_pins.h +++ b/arch/arm/include/asm/arch-mx6/mx6dl_pins.h @@ -50,6 +50,8 @@ #define NO_MUX_I 0 #define NO_PAD_I 0 enum { + MX6_PAD_CSI0_DAT10__UART1_TXD = IOMUX_PAD(0x0360, 0x004C, 3, 0x0000, 0, 0), + MX6_PAD_CSI0_DAT11__UART1_RXD = IOMUX_PAD(0x0364, 0x0050, 3, 0x08FC, 1, 0), MX6_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK = IOMUX_PAD(0x03B0, 0x009C, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), MX6_PAD_DI0_PIN15__IPU1_DI0_PIN15 = IOMUX_PAD(0x03B4, 0x00A0, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), MX6_PAD_DI0_PIN2__IPU1_DI0_PIN2 = IOMUX_PAD(0x03B8, 0x00A4, 0, 0x0000, 0, PAD_CTL_DSE_120ohm), @@ -90,6 +92,7 @@ enum { MX6_PAD_EIM_D27__UART2_RXD = IOMUX_PAD(0x0540, 0x0170, 4, 0x0904, 1, 0), MX6_PAD_EIM_D28__I2C1_SDA = IOMUX_PAD(0x0544, 0x0174, 1 | IOMUX_CONFIG_SION, 0x086C, 1, 0), MX6_PAD_EIM_D28__GPIO_3_28 = IOMUX_PAD(0x0544, 0x0174, 5, 0x0000, 0, 0), + MX6_PAD_EIM_D29__GPIO_3_29 = IOMUX_PAD(0x0548, 0x0178, 5, 0x0000, 0, 0), MX6_PAD_ENET_MDC__ENET_MDC = IOMUX_PAD(0x05B8, 0x01E8, 1, 0x0000, 0, 0), MX6_PAD_ENET_MDIO__ENET_MDIO = IOMUX_PAD(0x05BC, 0x01EC, 1, 0x0810, 0, 0), MX6_PAD_ENET_REF_CLK__ENET_TX_CLK = IOMUX_PAD(0x05C0, 0x01F0, 1, 0x0000, 0, 0), diff --git a/board/boundary/nitrogen6x/nitrogen6x.c b/board/boundary/nitrogen6x/nitrogen6x.c index 229c237839..cc071d6d38 100644 --- a/board/boundary/nitrogen6x/nitrogen6x.c +++ b/board/boundary/nitrogen6x/nitrogen6x.c @@ -304,6 +304,9 @@ int board_mmc_init(bd_t *bis) usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); + usdhc_cfg[0].max_bus_width = 4; + usdhc_cfg[1].max_bus_width = 4; + for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) { switch (index) { case 0: @@ -328,11 +331,6 @@ int board_mmc_init(bd_t *bis) } #endif -u32 get_board_rev(void) -{ - return 0x63000; -} - #ifdef CONFIG_MXC_SPI iomux_v3_cfg_t const ecspi1_pads[] = { /* SS1 */ diff --git a/board/freescale/mx6qsabreauto/mx6qsabreauto.c b/board/freescale/mx6qsabreauto/mx6qsabreauto.c index 91cc0073bd..aec3286e25 100644 --- a/board/freescale/mx6qsabreauto/mx6qsabreauto.c +++ b/board/freescale/mx6qsabreauto/mx6qsabreauto.c @@ -26,6 +26,7 @@ #include <asm/errno.h> #include <asm/gpio.h> #include <asm/imx-common/iomux-v3.h> +#include <asm/imx-common/boot_mode.h> #include <mmc.h> #include <fsl_esdhc.h> #include <miiphy.h> @@ -216,6 +217,23 @@ int board_init(void) return 0; } +#ifdef CONFIG_CMD_BMODE +static const struct boot_mode board_boot_modes[] = { + /* 4 bit bus width */ + {"mmc0", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)}, + {NULL, 0}, +}; +#endif + +int board_late_init(void) +{ +#ifdef CONFIG_CMD_BMODE + add_board_boot_modes(board_boot_modes); +#endif + + return 0; +} + int checkboard(void) { int rev = mx6sabre_rev(); diff --git a/board/freescale/mx6qsabrelite/README b/board/freescale/mx6qsabrelite/README index 6f2f5343de..12a9c856cf 100644 --- a/board/freescale/mx6qsabrelite/README +++ b/board/freescale/mx6qsabrelite/README @@ -40,7 +40,7 @@ enter the following commands: MX6Q SABRELITE U-Boot > mmc dev 0 MX6Q SABRELITE U-Boot > mmc read 0x10800000 0 200 - MX6Q SABRELITE U-Boot > sf probe 1 + MX6Q SABRELITE U-Boot > sf probe MX6Q SABRELITE U-Boot > sf erase 0 0x40000 MX6Q SABRELITE U-Boot > sf write 0x10800000 0 0x40000 @@ -63,7 +63,7 @@ https://wiki.linaro.org/Boards/MX6QSabreLite To build U-Boot for the SabreLite board: make mx6qsabrelite_config - make u-boot.imx + make To copy the resulting u-boot.imx to the SD card: diff --git a/board/freescale/mx6qsabrelite/mx6qsabrelite.c b/board/freescale/mx6qsabrelite/mx6qsabrelite.c index 5b69a6d2de..9f9cac82c4 100644 --- a/board/freescale/mx6qsabrelite/mx6qsabrelite.c +++ b/board/freescale/mx6qsabrelite/mx6qsabrelite.c @@ -274,6 +274,9 @@ int board_mmc_init(bd_t *bis) usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); + usdhc_cfg[0].max_bus_width = 4; + usdhc_cfg[1].max_bus_width = 4; + for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) { switch (index) { case 0: @@ -298,11 +301,6 @@ int board_mmc_init(bd_t *bis) } #endif -u32 get_board_rev(void) -{ - return 0x63000 ; -} - #ifdef CONFIG_MXC_SPI iomux_v3_cfg_t const ecspi1_pads[] = { /* SS1 */ diff --git a/board/freescale/mx6qsabresd/mx6qsabresd.c b/board/freescale/mx6qsabresd/mx6qsabresd.c index 2b3926aaf3..0d7cb9efd0 100644 --- a/board/freescale/mx6qsabresd/mx6qsabresd.c +++ b/board/freescale/mx6qsabresd/mx6qsabresd.c @@ -26,10 +26,12 @@ #include <asm/errno.h> #include <asm/gpio.h> #include <asm/imx-common/iomux-v3.h> +#include <asm/imx-common/boot_mode.h> #include <mmc.h> #include <fsl_esdhc.h> #include <miiphy.h> #include <netdev.h> + DECLARE_GLOBAL_DATA_PTR; #define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ @@ -145,21 +147,34 @@ struct fsl_esdhc_cfg usdhc_cfg[3] = { int board_mmc_getcd(struct mmc *mmc) { struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; + int ret = 0; switch (cfg->esdhc_base) { case USDHC2_BASE_ADDR: - return !gpio_get_value(USDHC2_CD_GPIO); + ret = !gpio_get_value(USDHC2_CD_GPIO); + break; case USDHC3_BASE_ADDR: - return !gpio_get_value(USDHC3_CD_GPIO); - default: - return 1; /* eMMC/uSDHC4 is always present */ + ret = !gpio_get_value(USDHC3_CD_GPIO); + break; + case USDHC4_BASE_ADDR: + ret = 1; /* eMMC/uSDHC4 is always present */ + break; } + + return ret; } int board_mmc_init(bd_t *bis) { int i; + /* + * According to the board_mmc_init() the following map is done: + * (U-boot device node) (Physical Port) + * mmc0 SD2 + * mmc1 SD3 + * mmc2 eMMC + */ for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) { switch (i) { case 0: @@ -239,11 +254,6 @@ int board_eth_init(bd_t *bis) return 0; } -u32 get_board_rev(void) -{ - return 0x63000; -} - int board_early_init_f(void) { setup_iomux_uart(); @@ -259,6 +269,26 @@ int board_init(void) return 0; } +#ifdef CONFIG_CMD_BMODE +static const struct boot_mode board_boot_modes[] = { + /* 4 bit bus width */ + {"sd2", MAKE_CFGVAL(0x40, 0x28, 0x00, 0x00)}, + {"sd3", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)}, + /* 8 bit bus width */ + {"emmc", MAKE_CFGVAL(0x40, 0x38, 0x00, 0x00)}, + {NULL, 0}, +}; +#endif + +int board_late_init(void) +{ +#ifdef CONFIG_CMD_BMODE + add_board_boot_modes(board_boot_modes); +#endif + + return 0; +} + int checkboard(void) { puts("Board: MX6Q-SabreSD\n"); diff --git a/board/wandboard/Makefile b/board/wandboard/Makefile new file mode 100644 index 0000000000..014ea6c1f9 --- /dev/null +++ b/board/wandboard/Makefile @@ -0,0 +1,29 @@ +# +# (C) Copyright 2013 Freescale Semiconductor, Inc. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# + +include $(TOPDIR)/config.mk + +LIB = $(obj)lib$(BOARD).o + +COBJS := wandboard.o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/wandboard/README b/board/wandboard/README new file mode 100644 index 0000000000..e0b0b33020 --- /dev/null +++ b/board/wandboard/README @@ -0,0 +1,40 @@ +U-Boot for Wandboard +-------------------- + +This file contains information for the port of U-Boot to the Wandboard. + +Wandboard is a development board that has two variants: one version based +on mx6 dual lite and another one based on mx6 solo. + +For more details about Wandboard, please refer to: +http://www.wandboard.org/ + +Building U-boot for Wandboard +----------------------------- + +To build U-Boot for the Wandboard Dual Lite version: + +$ make wanboard_dl_config +$ make + +To build U-Boot for the Wandboard Solo version: + +$ make wanboard_solo_config +$ make + +Flashing U-boot into the SD card +-------------------------------- + +- After the 'make' command completes, the generated 'u-boot.imx' binary must be +flashed into the SD card; + +$ sudo dd if=u-boot.imx of=/dev/mmcblk0 bs=512 seek=2; sync + +(Note - the SD card node may vary, so adjust this as needed). + +- Insert the SD card into the slot located in the bottom of the board (same side +as the mx6 processor) + +- Connect the serial cable to the host PC + +- Power up the board and U-boot messages will appear in the serial console. diff --git a/board/wandboard/wandboard.c b/board/wandboard/wandboard.c new file mode 100644 index 0000000000..ac7b89aaec --- /dev/null +++ b/board/wandboard/wandboard.c @@ -0,0 +1,178 @@ +/* + * Copyright (C) 2013 Freescale Semiconductor, Inc. + * + * Author: Fabio Estevam <fabio.estevam@freescale.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +#include <asm/arch/clock.h> +#include <asm/arch/iomux.h> +#include <asm/arch/imx-regs.h> +#include <asm/arch/mx6-pins.h> +#include <asm/arch/sys_proto.h> +#include <asm/gpio.h> +#include <asm/imx-common/iomux-v3.h> +#include <asm/io.h> +#include <asm/sizes.h> +#include <common.h> +#include <fsl_esdhc.h> +#include <mmc.h> +#include <miiphy.h> +#include <netdev.h> + +DECLARE_GLOBAL_DATA_PTR; + +#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \ + PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS) + +#define ENET_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \ + PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \ + PAD_CTL_DSE_40ohm | PAD_CTL_HYS) + +#define ETH_PHY_RESET IMX_GPIO_NR(3, 29) + +int dram_init(void) +{ + gd->ram_size = CONFIG_DDR_MB * SZ_1M; + + return 0; +} + +static iomux_v3_cfg_t const uart1_pads[] = { + MX6_PAD_CSI0_DAT10__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL), + MX6_PAD_CSI0_DAT11__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL), +}; + +static iomux_v3_cfg_t const usdhc3_pads[] = { + MX6_PAD_SD3_CLK__USDHC3_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_CMD__USDHC3_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL), + MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL), +}; + +static iomux_v3_cfg_t const enet_pads[] = { + MX6_PAD_ENET_MDIO__ENET_MDIO | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_ENET_MDC__ENET_MDC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TXC__ENET_RGMII_TXC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD0__ENET_RGMII_TD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD1__ENET_RGMII_TD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD2__ENET_RGMII_TD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TD3__ENET_RGMII_TD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_ENET_REF_CLK__ENET_TX_CLK | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RXC__ENET_RGMII_RXC | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD0__ENET_RGMII_RD0 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD1__ENET_RGMII_RD1 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD2__ENET_RGMII_RD2 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RD3__ENET_RGMII_RD3 | MUX_PAD_CTRL(ENET_PAD_CTRL), + MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL | MUX_PAD_CTRL(ENET_PAD_CTRL), + /* AR8031 PHY Reset */ + MX6_PAD_EIM_D29__GPIO_3_29 | MUX_PAD_CTRL(NO_PAD_CTRL), +}; + +static void setup_iomux_uart(void) +{ + imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads)); +} + +static void setup_iomux_enet(void) +{ + imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads)); + + /* Reset AR8031 PHY */ + gpio_direction_output(ETH_PHY_RESET, 0); + udelay(500); + gpio_set_value(ETH_PHY_RESET, 1); +} + +static struct fsl_esdhc_cfg usdhc_cfg[1] = { + {USDHC3_BASE_ADDR}, +}; + +int board_mmc_init(bd_t *bis) +{ + imx_iomux_v3_setup_multiple_pads(usdhc3_pads, ARRAY_SIZE(usdhc3_pads)); + + usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); + usdhc_cfg[0].max_bus_width = 4; + + return fsl_esdhc_initialize(bis, &usdhc_cfg[0]); +} + +static int mx6_rgmii_rework(struct phy_device *phydev) +{ + unsigned short val; + + /* To enable AR8031 ouput a 125MHz clk from CLK_25M */ + phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7); + phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016); + phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007); + + val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe); + val &= 0xffe3; + val |= 0x18; + phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val); + + /* introduce tx clock delay */ + phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5); + val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e); + val |= 0x0100; + phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val); + + return 0; +} + +int board_phy_config(struct phy_device *phydev) +{ + mx6_rgmii_rework(phydev); + + if (phydev->drv->config) + phydev->drv->config(phydev); + + return 0; +} + +int board_eth_init(bd_t *bis) +{ + int ret; + + setup_iomux_enet(); + + ret = cpu_eth_init(bis); + if (ret) + printf("FEC MXC: %s:failed\n", __func__); + + return 0; +} + +int board_early_init_f(void) +{ + setup_iomux_uart(); + return 0; +} + +int board_init(void) +{ + /* address of boot parameters */ + gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; + + return 0; +} + +int checkboard(void) +{ + puts("Board: Wandboard\n"); + + return 0; +} diff --git a/boards.cfg b/boards.cfg index 5fc70be8f5..d7bda3663c 100644 --- a/boards.cfg +++ b/boards.cfg @@ -196,7 +196,8 @@ mx23_olinuxino arm arm926ejs mx23_olinuxino olimex apx4devkit arm arm926ejs apx4devkit bluegiga mxs apx4devkit mx23evk arm arm926ejs mx23evk freescale mxs mx23evk m28evk arm arm926ejs m28evk denx mxs m28evk -mx28evk arm arm926ejs mx28evk freescale mxs mx28evk +mx28evk arm arm926ejs mx28evk freescale mxs mx28evk:ENV_IS_IN_MMC +mx28evk_nand arm arm926ejs mx28evk freescale mxs mx28evk:ENV_IS_IN_NAND sc_sps_1 arm arm926ejs sc_sps_1 schulercontrol mxs nhk8815 arm arm926ejs nhk8815 st nomadik nhk8815_onenand arm arm926ejs nhk8815 st nomadik nhk8815:BOOT_ONENAND @@ -264,6 +265,8 @@ nitrogen6q arm armv7 nitrogen6x boundar nitrogen6q2g arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6q2g.cfg,MX6Q,DDR_MB=2048 nitrogen6s arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s.cfg,MX6S,DDR_MB=512 nitrogen6s1g arm armv7 nitrogen6x boundary mx6 nitrogen6x:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s1g.cfg,MX6S,DDR_MB=1024 +wandboard_dl arm armv7 wandboard - mx6 wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6dl.cfg,MX6DL,DDR_MB=1024 +wandboard_solo arm armv7 wandboard - mx6 wandboard:IMX_CONFIG=board/boundary/nitrogen6x/nitrogen6s.cfg,MX6S,DDR_MB=512 cm_t35 arm armv7 cm_t35 - omap3 omap3_overo arm armv7 overo - omap3 omap3_pandora arm armv7 pandora - omap3 diff --git a/doc/README.mx28evk b/doc/README.mx28evk index 2fc50696f5..76db474bfb 100644 --- a/doc/README.mx28evk +++ b/doc/README.mx28evk @@ -23,6 +23,24 @@ To boot MX28EVK from an SD card, set the boot mode DIP switches as: * VDD 5V: To the left (off) * Hold Button: Down (off) + +Environment Storage +------------------- + +There are two targets for mx28evk: + +"make mx28evk_config" - store enviroment variables into MMC + +or + +"make mx28evk_nand_config" - store enviroment variables into NAND flash + +Choose the target accordingly. + +Note: The mx28evk board does not come with a NAND flash populated from the +factory. It comes with an empty slot (U23), which allows the insertion of a +48-pin TSOP flash device. + Follow the instructions from doc/README.mx28_common to generate a bootable SD card. diff --git a/drivers/mmc/fsl_esdhc.c b/drivers/mmc/fsl_esdhc.c index 54b5363169..35f879ea6e 100644 --- a/drivers/mmc/fsl_esdhc.c +++ b/drivers/mmc/fsl_esdhc.c @@ -580,6 +580,13 @@ int fsl_esdhc_initialize(bd_t *bis, struct fsl_esdhc_cfg *cfg) mmc->host_caps = MMC_MODE_4BIT | MMC_MODE_8BIT | MMC_MODE_HC; + if (cfg->max_bus_width > 0) { + if (cfg->max_bus_width < 8) + mmc->host_caps &= ~MMC_MODE_8BIT; + if (cfg->max_bus_width < 4) + mmc->host_caps &= ~MMC_MODE_4BIT; + } + if (caps & ESDHC_HOSTCAPBLT_HSS) mmc->host_caps |= MMC_MODE_HS_52MHz | MMC_MODE_HS; diff --git a/drivers/spi/mxc_spi.c b/drivers/spi/mxc_spi.c index d792d8d493..cb48019a42 100644 --- a/drivers/spi/mxc_spi.c +++ b/drivers/spi/mxc_spi.c @@ -137,11 +137,11 @@ static s32 spi_cfg_mxc(struct mxc_spi_slave *mxcs, unsigned int cs, return -1; } - reg_ctrl = reg_read(®s->ctrl); - /* Reset spi */ - reg_write(®s->ctrl, (reg_ctrl & ~MXC_CSPICTRL_EN)); - reg_write(®s->ctrl, (reg_ctrl | MXC_CSPICTRL_EN)); + reg_write(®s->ctrl, 0); + reg_write(®s->ctrl, MXC_CSPICTRL_EN); + + reg_ctrl = reg_read(®s->ctrl); /* * The following computation is taken directly from Freescale's code. diff --git a/include/configs/mx23_olinuxino.h b/include/configs/mx23_olinuxino.h index 03893d744d..38ad7f4d8f 100644 --- a/include/configs/mx23_olinuxino.h +++ b/include/configs/mx23_olinuxino.h @@ -24,57 +24,57 @@ /* * SoC configurations */ -#define CONFIG_MX23 /* i.MX23 SoC */ -#define CONFIG_MXS_GPIO /* GPIO control */ -#define CONFIG_SYS_HZ 1000 /* Ticks per second */ +#define CONFIG_MX23 /* i.MX23 SoC */ +#define CONFIG_MXS_GPIO /* GPIO control */ +#define CONFIG_SYS_HZ 1000 /* Ticks per second */ -#define CONFIG_MACH_TYPE 4105 +#define CONFIG_MACH_TYPE 4105 #include <asm/arch/regs-base.h> -#define CONFIG_SYS_NO_FLASH -#define CONFIG_BOARD_EARLY_INIT_F -#define CONFIG_ARCH_MISC_INIT +#define CONFIG_SYS_NO_FLASH +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_ARCH_MISC_INIT /* * SPL */ -#define CONFIG_SPL -#define CONFIG_SPL_NO_CPU_SUPPORT_CODE -#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" -#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" -#define CONFIG_SPL_LIBCOMMON_SUPPORT -#define CONFIG_SPL_LIBGENERIC_SUPPORT -#define CONFIG_SPL_GPIO_SUPPORT +#define CONFIG_SPL +#define CONFIG_SPL_NO_CPU_SUPPORT_CODE +#define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" +#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/arm926ejs/mxs/u-boot-spl.lds" +#define CONFIG_SPL_LIBCOMMON_SUPPORT +#define CONFIG_SPL_LIBGENERIC_SUPPORT +#define CONFIG_SPL_GPIO_SUPPORT /* * U-Boot Commands */ #include <config_cmd_default.h> -#define CONFIG_DISPLAY_CPUINFO -#define CONFIG_DOS_PARTITION +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DOS_PARTITION -#define CONFIG_CMD_CACHE -#define CONFIG_CMD_DHCP -#define CONFIG_CMD_EXT2 -#define CONFIG_CMD_FAT -#define CONFIG_CMD_GPIO -#define CONFIG_CMD_LED -#define CONFIG_CMD_MMC -#define CONFIG_CMD_NET -#define CONFIG_CMD_USB +#define CONFIG_CMD_CACHE +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_CMD_GPIO +#define CONFIG_CMD_LED +#define CONFIG_CMD_MMC +#define CONFIG_CMD_NET +#define CONFIG_CMD_USB /* * Memory configurations */ -#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ -#define PHYS_SDRAM_1 0x40000000 /* Base address */ -#define PHYS_SDRAM_1_SIZE 0x08000000 /* Max 128 MB RAM */ -#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ -#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Initial data */ -#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ -#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ -#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 +#define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ +#define PHYS_SDRAM_1 0x40000000 /* Base address */ +#define PHYS_SDRAM_1_SIZE 0x08000000 /* Max 128 MB RAM */ +#define CONFIG_SYS_MALLOC_LEN 0x00400000 /* 4 MB for malloc */ +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* Initial data */ +#define CONFIG_SYS_MEMTEST_START 0x40000000 /* Memtest start adr */ +#define CONFIG_SYS_MEMTEST_END 0x40400000 /* 4 MB RAM test */ +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1 /* Point initial SP in SRAM so SPL can use it too. */ #define CONFIG_SYS_INIT_RAM_ADDR 0x00000000 @@ -89,49 +89,49 @@ * strange BUG in ROM corrupting first 4 bytes of RAM when loading U-Boot * binary. In case there was more of this mess, 0x100 bytes are skipped. */ -#define CONFIG_SYS_TEXT_BASE 0x40000100 +#define CONFIG_SYS_TEXT_BASE 0x40000100 /* * U-Boot general configurations */ -#define CONFIG_SYS_LONGHELP -#define CONFIG_SYS_PROMPT "=> " -#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ -#define CONFIG_SYS_PBSIZE \ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_PROMPT "=> " +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ +#define CONFIG_SYS_PBSIZE \ (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) /* Print buffer size */ -#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ -#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE +#define CONFIG_SYS_MAXARGS 32 /* Max number of command args */ +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot argument buffer size */ -#define CONFIG_VERSION_VARIABLE /* U-BOOT version */ -#define CONFIG_AUTO_COMPLETE /* Command auto complete */ -#define CONFIG_CMDLINE_EDITING /* Command history etc */ -#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_VERSION_VARIABLE /* U-BOOT version */ +#define CONFIG_AUTO_COMPLETE /* Command auto complete */ +#define CONFIG_CMDLINE_EDITING /* Command history etc */ +#define CONFIG_SYS_HUSH_PARSER /* * Serial Driver */ -#define CONFIG_PL011_SERIAL -#define CONFIG_PL011_CLOCK 24000000 -#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } -#define CONFIG_CONS_INDEX 0 -#define CONFIG_BAUDRATE 115200 /* Default baud rate */ +#define CONFIG_PL011_SERIAL +#define CONFIG_PL011_CLOCK 24000000 +#define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } +#define CONFIG_CONS_INDEX 0 +#define CONFIG_BAUDRATE 115200 /* Default baud rate */ /* * Status LED */ -#define CONFIG_STATUS_LED -#define CONFIG_GPIO_LED -#define CONFIG_BOARD_SPECIFIC_LED -#define STATUS_LED_BOOT 0 -#define STATUS_LED_BIT MX23_PAD_SSP1_DETECT__GPIO_2_1 -#define STATUS_LED_STATE STATUS_LED_ON -#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) +#define CONFIG_STATUS_LED +#define CONFIG_GPIO_LED +#define CONFIG_BOARD_SPECIFIC_LED +#define STATUS_LED_BOOT 0 +#define STATUS_LED_BIT MX23_PAD_SSP1_DETECT__GPIO_2_1 +#define STATUS_LED_STATE STATUS_LED_ON +#define STATUS_LED_PERIOD (CONFIG_SYS_HZ / 2) /* * MMC Driver */ -#ifdef CONFIG_CMD_MMC +#ifdef CONFIG_CMD_MMC #define CONFIG_MMC #define CONFIG_BOUNCE_BUFFER #define CONFIG_GENERIC_MMC @@ -144,41 +144,41 @@ #define CONFIG_APBH_DMA /* USB */ -#ifdef CONFIG_CMD_USB -#define CONFIG_USB_EHCI -#define CONFIG_USB_EHCI_MXS -#define CONFIG_EHCI_MXS_PORT0 -#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 -#define CONFIG_EHCI_IS_TDI -#define CONFIG_USB_STORAGE +#ifdef CONFIG_CMD_USB +#define CONFIG_USB_EHCI +#define CONFIG_USB_EHCI_MXS +#define CONFIG_EHCI_MXS_PORT0 +#define CONFIG_USB_MAX_CONTROLLER_COUNT 1 +#define CONFIG_EHCI_IS_TDI +#define CONFIG_USB_STORAGE #endif /* Ethernet */ -#ifdef CONFIG_CMD_NET -#define CONFIG_USB_HOST_ETHER -#define CONFIG_USB_ETHER_SMSC95XX +#ifdef CONFIG_CMD_NET +#define CONFIG_USB_HOST_ETHER +#define CONFIG_USB_ETHER_SMSC95XX #endif /* * Boot Linux */ -#define CONFIG_CMDLINE_TAG -#define CONFIG_SETUP_MEMORY_TAGS -#define CONFIG_BOOTDELAY 3 -#define CONFIG_BOOTFILE "uImage" -#define CONFIG_LOADADDR 0x42000000 -#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR -#define CONFIG_OF_LIBFDT +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_BOOTDELAY 3 +#define CONFIG_BOOTFILE "uImage" +#define CONFIG_LOADADDR 0x42000000 +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR +#define CONFIG_OF_LIBFDT /* * Environment */ -#define CONFIG_ENV_IS_IN_MMC -#define CONFIG_ENV_OVERWRITE -#ifdef CONFIG_ENV_IS_IN_MMC -#define CONFIG_ENV_OFFSET (256 * 1024) -#define CONFIG_ENV_SIZE (16 * 1024) -#define CONFIG_SYS_MMC_ENV_DEV 0 +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_OVERWRITE +#ifdef CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_OFFSET (256 * 1024) +#define CONFIG_ENV_SIZE (16 * 1024) +#define CONFIG_SYS_MMC_ENV_DEV 0 #endif /* @@ -227,7 +227,7 @@ "else " \ "bootm; " \ "fi;\0" \ - "netargs=setenv bootargs console=${console_mainline},${baudrate} " \ + "netargs=setenv bootargs console=${console},${baudrate} " \ "root=/dev/nfs " \ "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ "netboot=echo Booting from net ...; " \ diff --git a/include/configs/mx25pdk.h b/include/configs/mx25pdk.h index c10e78b634..4782f68fc4 100644 --- a/include/configs/mx25pdk.h +++ b/include/configs/mx25pdk.h @@ -124,6 +124,10 @@ #define CONFIG_SYS_I2C_BASE IMX_I2C_BASE #define CONFIG_SYS_I2C_SPEED 100000 +/* RTC */ +#define CONFIG_RTC_IMXDI +#define CONFIG_CMD_DATE + /* Ethernet Configs */ #define CONFIG_CMD_PING diff --git a/include/configs/mx28evk.h b/include/configs/mx28evk.h index 0d918a153d..d470b4733e 100644 --- a/include/configs/mx28evk.h +++ b/include/configs/mx28evk.h @@ -19,9 +19,7 @@ #ifndef __MX28EVK_CONFIG_H__ #define __MX28EVK_CONFIG_H__ -/* - * SoC configurations - */ +/* SoC configurations */ #define CONFIG_MX28 /* i.MX28 SoC */ #define CONFIG_MXS_GPIO /* GPIO control */ @@ -35,9 +33,7 @@ #define CONFIG_BOARD_EARLY_INIT_F #define CONFIG_ARCH_MISC_INIT -/* - * SPL - */ +/* SPL */ #define CONFIG_SPL #define CONFIG_SPL_NO_CPU_SUPPORT_CODE #define CONFIG_SPL_START_S_PATH "arch/arm/cpu/arm926ejs/mxs" @@ -46,9 +42,7 @@ #define CONFIG_SPL_LIBGENERIC_SUPPORT #define CONFIG_SPL_GPIO_SUPPORT -/* - * U-Boot Commands - */ +/* U-Boot Commands */ #include <config_cmd_default.h> #define CONFIG_DISPLAY_CPUINFO #define CONFIG_DOS_PARTITION @@ -68,11 +62,9 @@ #define CONFIG_CMD_SPI #define CONFIG_CMD_USB #define CONFIG_CMD_BOOTZ -#define CONFIG_CMD_I2C +#define CONFIG_CMD_NAND -/* - * Memory configurations - */ +/* Memory configurations */ #define CONFIG_NR_DRAM_BANKS 1 /* 1 bank of DRAM */ #define PHYS_SDRAM_1 0x40000000 /* Base address */ #define PHYS_SDRAM_1_SIZE 0x40000000 /* Max 1 GB RAM */ @@ -98,9 +90,7 @@ #define CONFIG_SYS_TEXT_BASE 0x40000100 #define CONFIG_ENV_OVERWRITE -/* - * U-Boot general configurations - */ +/* U-Boot general configurations */ #define CONFIG_SYS_LONGHELP #define CONFIG_SYS_PROMPT "MX28EVK U-Boot > " #define CONFIG_SYS_CBSIZE 1024 /* Console I/O buffer size */ @@ -115,24 +105,17 @@ #define CONFIG_CMDLINE_EDITING /* Command history etc */ #define CONFIG_SYS_HUSH_PARSER -/* - * Serial Driver - */ +/* Serial Driver */ #define CONFIG_PL011_SERIAL #define CONFIG_PL011_CLOCK 24000000 #define CONFIG_PL01x_PORTS { (void *)MXS_UARTDBG_BASE } #define CONFIG_CONS_INDEX 0 #define CONFIG_BAUDRATE 115200 /* Default baud rate */ -/* - * DMA - */ +/* DMA */ #define CONFIG_APBH_DMA -/* - * MMC Driver - */ -#define CONFIG_ENV_IS_IN_MMC +/* MMC Driver */ #ifdef CONFIG_ENV_IS_IN_MMC #define CONFIG_ENV_OFFSET (256 * 1024) #define CONFIG_ENV_SIZE (16 * 1024) @@ -146,19 +129,44 @@ #define CONFIG_MXS_MMC #endif -/* - * NAND Driver - */ +/* NAND Driver */ +#define CONFIG_ENV_SIZE (16 * 1024) #ifdef CONFIG_CMD_NAND #define CONFIG_NAND_MXS #define CONFIG_SYS_MAX_NAND_DEVICE 1 #define CONFIG_SYS_NAND_BASE 0x60000000 #define CONFIG_SYS_NAND_5_ADDR_CYCLE + +/* Environment is in NAND */ +#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE +#define CONFIG_ENV_SECT_SIZE (128 * 1024) +#define CONFIG_ENV_RANGE (512 * 1024) +#ifndef CONFIG_ENV_OFFSET +#define CONFIG_ENV_OFFSET 0x300000 #endif +#define CONFIG_ENV_OFFSET_REDUND \ + (CONFIG_ENV_OFFSET + CONFIG_ENV_RANGE) -/* - * Ethernet on SOC (FEC) - */ +#define CONFIG_CMD_UBI +#define CONFIG_CMD_UBIFS +#define CONFIG_CMD_MTDPARTS +#define CONFIG_RBTREE +#define CONFIG_LZO +#define CONFIG_MTD_DEVICE +#define CONFIG_MTD_PARTITIONS +#define MTDIDS_DEFAULT "nand0=gpmi-nand" +#define MTDPARTS_DEFAULT \ + "mtdparts=gpmi-nand:" \ + "3m(bootloader)ro," \ + "512k(environment)," \ + "512k(redundant-environment)," \ + "4m(kernel)," \ + "128k(fdt)," \ + "8m(ramdisk)," \ + "-(filesystem)" +#endif + +/* Ethernet on SOC (FEC) */ #ifdef CONFIG_CMD_NET #define CONFIG_NET_MULTI #define CONFIG_ETHPRIME "FEC0" @@ -168,16 +176,12 @@ #define CONFIG_MX28_FEC_MAC_IN_OCOTP #endif -/* - * RTC - */ +/* RTC */ #ifdef CONFIG_CMD_DATE #define CONFIG_RTC_MXS #endif -/* - * USB - */ +/* USB */ #ifdef CONFIG_CMD_USB #define CONFIG_USB_EHCI #define CONFIG_USB_EHCI_MXS @@ -197,9 +201,7 @@ #define CONFIG_SYS_I2C_SPEED 400000 #endif -/* - * SPI - */ +/* SPI */ #ifdef CONFIG_CMD_SPI #define CONFIG_HARD_SPI #define CONFIG_MXS_SPI @@ -232,9 +234,7 @@ #endif #endif -/* - * Boot Linux - */ +/* Boot Linux */ #define CONFIG_CMDLINE_TAG #define CONFIG_SETUP_MEMORY_TAGS #define CONFIG_BOOTDELAY 1 @@ -243,9 +243,7 @@ #define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR #define CONFIG_OF_LIBFDT -/* - * Extra Environments - */ +/* Extra Environments */ #define CONFIG_EXTRA_ENV_SETTINGS \ "update_nand_full_filename=u-boot.nand\0" \ "update_nand_firmware_filename=u-boot.sb\0" \ diff --git a/include/configs/mx6qsabre_common.h b/include/configs/mx6qsabre_common.h index 9eda9ed91a..0965b8f8d6 100644 --- a/include/configs/mx6qsabre_common.h +++ b/include/configs/mx6qsabre_common.h @@ -36,6 +36,7 @@ #define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * 1024 * 1024) #define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_BOARD_LATE_INIT #define CONFIG_MXC_GPIO #define CONFIG_MXC_UART @@ -75,6 +76,7 @@ /* Command definition */ #include <config_cmd_default.h> +#define CONFIG_CMD_BMODE #define CONFIG_CMD_BOOTZ #undef CONFIG_CMD_IMLS diff --git a/include/configs/mx6qsabrelite.h b/include/configs/mx6qsabrelite.h index 5dc8255cec..6d4b837352 100644 --- a/include/configs/mx6qsabrelite.h +++ b/include/configs/mx6qsabrelite.h @@ -216,7 +216,6 @@ "fi;\0" #define CONFIG_BOOTCOMMAND \ - "mmc dev ${mmcdev};" \ "mmc dev ${mmcdev}; if mmc rescan; then " \ "if run loadbootscript; then " \ "run bootscript; " \ @@ -228,8 +227,6 @@ "fi; " \ "else run netboot; fi" -#define CONFIG_ARP_TIMEOUT 200UL - /* Miscellaneous configurable options */ #define CONFIG_SYS_LONGHELP #define CONFIG_SYS_HUSH_PARSER diff --git a/include/configs/wandboard.h b/include/configs/wandboard.h new file mode 100644 index 0000000000..120e3f6ffd --- /dev/null +++ b/include/configs/wandboard.h @@ -0,0 +1,209 @@ +/* + * Copyright (C) 2013 Freescale Semiconductor, Inc. + * + * Configuration settings for the Wandboard. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + */ + +#ifndef __CONFIG_H +#define __CONFIG_H + +#include <asm/arch/imx-regs.h> +#include <asm/imx-common/gpio.h> +#include <asm/sizes.h> + +#define CONFIG_MX6 +#define CONFIG_DISPLAY_CPUINFO +#define CONFIG_DISPLAY_BOARDINFO + +#define MACH_TYPE_WANDBOARD 4412 +#define CONFIG_MACH_TYPE MACH_TYPE_WANDBOARD + +#define CONFIG_CMDLINE_TAG +#define CONFIG_SETUP_MEMORY_TAGS +#define CONFIG_INITRD_TAG +#define CONFIG_REVISION_TAG + +/* Size of malloc() pool */ +#define CONFIG_SYS_MALLOC_LEN (3 * SZ_1M) + +#define CONFIG_BOARD_EARLY_INIT_F +#define CONFIG_MXC_GPIO + +#define CONFIG_MXC_UART +#define CONFIG_MXC_UART_BASE UART1_BASE + +/* allow to overwrite serial and ethaddr */ +#define CONFIG_ENV_OVERWRITE +#define CONFIG_CONS_INDEX 1 +#define CONFIG_BAUDRATE 115200 + +/* Command definition */ +#include <config_cmd_default.h> + +#undef CONFIG_CMD_IMLS + +#define CONFIG_BOOTDELAY 5 + +#define CONFIG_SYS_MEMTEST_START 0x10000000 +#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + 500 * SZ_1M) +#define CONFIG_LOADADDR 0x12000000 +#define CONFIG_SYS_TEXT_BASE 0x17800000 + +/* MMC Configuration */ +#define CONFIG_FSL_ESDHC +#define CONFIG_FSL_USDHC +#define CONFIG_SYS_FSL_ESDHC_ADDR 0 + +#define CONFIG_MMC +#define CONFIG_CMD_MMC +#define CONFIG_GENERIC_MMC +#define CONFIG_BOUNCE_BUFFER +#define CONFIG_CMD_EXT2 +#define CONFIG_CMD_FAT +#define CONFIG_DOS_PARTITION + +/* Ethernet Configuration */ +#define CONFIG_CMD_PING +#define CONFIG_CMD_DHCP +#define CONFIG_CMD_MII +#define CONFIG_CMD_NET +#define CONFIG_FEC_MXC +#define CONFIG_MII +#define IMX_FEC_BASE ENET_BASE_ADDR +#define CONFIG_FEC_XCV_TYPE RGMII +#define CONFIG_ETHPRIME "FEC" +#define CONFIG_FEC_MXC_PHYADDR 1 +#define CONFIG_PHYLIB +#define CONFIG_PHY_ATHEROS + +#if defined(CONFIG_MX6DL) +#define CONFIG_DEFAULT_FDT_FILE "imx6dl-wandboard.dtb" +#elif defined(CONFIG_MX6S) +#define CONFIG_DEFAULT_FDT_FILE "imx6s-wandboard.dtb" +#endif + +#define CONFIG_EXTRA_ENV_SETTINGS \ + "script=boot.scr\0" \ + "uimage=uImage\0" \ + "console=ttymxc0\0" \ + "fdt_high=0xffffffff\0" \ + "initrd_high=0xffffffff\0" \ + "fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \ + "fdt_addr=0x11000000\0" \ + "boot_fdt=try\0" \ + "ip_dyn=yes\0" \ + "mmcdev=0\0" \ + "mmcpart=2\0" \ + "mmcroot=/dev/mmcblk0p3 rootwait rw\0" \ + "mmcargs=setenv bootargs console=${console},${baudrate} " \ + "root=${mmcroot}\0" \ + "loadbootscript=" \ + "fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \ + "bootscript=echo Running bootscript from mmc ...; " \ + "source\0" \ + "loaduimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${uimage}\0" \ + "loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \ + "mmcboot=echo Booting from mmc ...; " \ + "run mmcargs; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if run loadfdt; then " \ + "bootm ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootm; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootm; " \ + "fi;\0" \ + "netargs=setenv bootargs console=${console},${baudrate} " \ + "root=/dev/nfs " \ + "ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \ + "netboot=echo Booting from net ...; " \ + "run netargs; " \ + "if test ${ip_dyn} = yes; then " \ + "setenv get_cmd dhcp; " \ + "else " \ + "setenv get_cmd tftp; " \ + "fi; " \ + "${get_cmd} ${uimage}; " \ + "if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \ + "if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \ + "bootm ${loadaddr} - ${fdt_addr}; " \ + "else " \ + "if test ${boot_fdt} = try; then " \ + "bootm; " \ + "else " \ + "echo WARN: Cannot load the DT; " \ + "fi; " \ + "fi; " \ + "else " \ + "bootm; " \ + "fi;\0" + +#define CONFIG_BOOTCOMMAND \ + "mmc dev ${mmcdev}; if mmc rescan; then " \ + "if run loadbootscript; then " \ + "run bootscript; " \ + "else " \ + "if run loaduimage; then " \ + "run mmcboot; " \ + "else run netboot; " \ + "fi; " \ + "fi; " \ + "else run netboot; fi" + +/* Miscellaneous configurable options */ +#define CONFIG_SYS_LONGHELP +#define CONFIG_SYS_HUSH_PARSER +#define CONFIG_SYS_PROMPT "=> " +#define CONFIG_AUTO_COMPLETE +#define CONFIG_SYS_CBSIZE 256 + +/* Print Buffer Size */ +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16) +#define CONFIG_SYS_MAXARGS 16 +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE + +#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR +#define CONFIG_SYS_HZ 1000 + +#define CONFIG_CMDLINE_EDITING + +/* Physical Memory Map */ +#define CONFIG_NR_DRAM_BANKS 1 +#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR + +#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM +#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR +#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE + +#define CONFIG_SYS_INIT_SP_OFFSET \ + (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) +#define CONFIG_SYS_INIT_SP_ADDR \ + (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET) + +/* FLASH and environment organization */ +#define CONFIG_SYS_NO_FLASH + +#define CONFIG_ENV_SIZE (8 * 1024) + +#define CONFIG_ENV_IS_IN_MMC +#define CONFIG_ENV_OFFSET (6 * 64 * 1024) +#define CONFIG_SYS_MMC_ENV_DEV 0 + +#define CONFIG_OF_LIBFDT +#define CONFIG_CMD_BOOTZ + +#ifndef CONFIG_SYS_DCACHE_OFF +#define CONFIG_CMD_CACHE +#endif + +#endif /* __CONFIG_H * */ diff --git a/include/fsl_esdhc.h b/include/fsl_esdhc.h index 47d2fe4f18..0a1a0715e9 100644 --- a/include/fsl_esdhc.h +++ b/include/fsl_esdhc.h @@ -168,6 +168,7 @@ struct fsl_esdhc_cfg { u32 esdhc_base; u32 sdhc_clk; + u8 max_bus_width; }; /* Select the correct accessors depending on endianess */ |