diff options
Diffstat (limited to 'board/nvidia')
| -rw-r--r-- | board/nvidia/common/uart-spi-switch.c | 29 | ||||
| -rw-r--r-- | board/nvidia/dts/tegra2-harmony.dts | 57 | ||||
| -rw-r--r-- | board/nvidia/dts/tegra2-ventana.dts | 57 | ||||
| -rw-r--r-- | board/nvidia/dts/tegra2-whistler.dts | 67 | ||||
| -rw-r--r-- | board/nvidia/harmony/harmony.c | 4 | ||||
| -rw-r--r-- | board/nvidia/seaboard/seaboard.c | 4 | ||||
| -rw-r--r-- | board/nvidia/whistler/Makefile | 48 | ||||
| -rw-r--r-- | board/nvidia/whistler/whistler.c | 116 |
8 files changed, 357 insertions, 25 deletions
diff --git a/board/nvidia/common/uart-spi-switch.c b/board/nvidia/common/uart-spi-switch.c index 23aa0b9d19..307937a836 100644 --- a/board/nvidia/common/uart-spi-switch.c +++ b/board/nvidia/common/uart-spi-switch.c @@ -21,12 +21,11 @@ */ #include <common.h> -#include <ns16550.h> #include <asm/gpio.h> #include <asm/arch/pinmux.h> #include <asm/arch/uart-spi-switch.h> #include <asm/arch/tegra2.h> -#include <asm/arch/tegra2_spi.h> +#include <asm/arch/tegra_spi.h> /* position of the UART/SPI select switch */ @@ -40,7 +39,6 @@ enum spi_uart_switch { /* Information about the spi/uart switch */ struct spi_uart { int gpio; /* GPIO to control switch */ - NS16550_t regs; /* Address of UART affected */ u32 port; /* Port number of UART affected */ }; @@ -52,7 +50,6 @@ static void get_config(struct spi_uart *config) { #if defined CONFIG_SPI_CORRUPTS_UART config->gpio = CONFIG_UART_DISABLE_GPIO; - config->regs = (NS16550_t)CONFIG_SPI_CORRUPTS_UART; config->port = CONFIG_SPI_CORRUPTS_UART_NR; #else config->gpio = -1; @@ -101,34 +98,24 @@ static void spi_uart_switch(struct spi_uart *config, if (switch_pos == SWITCH_BOTH || new_pos == switch_pos) return; - /* if the UART was selected, allow it to drain */ - if (switch_pos == SWITCH_UART) - NS16550_drain(config->regs, config->port); + /* pre-delay, allow SPI/UART to settle, FIFO to empty, etc. */ + udelay(CONFIG_SPI_CORRUPTS_UART_DLY); /* We need to dynamically change the pinmux, shared w/UART RXD/CTS */ pinmux_set_func(PINGRP_GMC, new_pos == SWITCH_SPI ? PMUX_FUNC_SFLASH : PMUX_FUNC_UARTD); /* - * On Seaboard, MOSI/MISO are shared w/UART. - * Use GPIO I3 (UART_DISABLE) to tristate UART during SPI activity. - * Enable UART later (cs_deactivate) so we can use it for U-Boot comms. - */ + * On Seaboard, MOSI/MISO are shared w/UART. + * Use GPIO I3 (UART_DISABLE) to tristate UART during SPI activity. + * Enable UART later (cs_deactivate) so we can use it for U-Boot comms. + */ gpio_direction_output(config->gpio, new_pos == SWITCH_SPI); switch_pos = new_pos; - - /* if the SPI was selected, clear any junk bytes in the UART */ - if (switch_pos == SWITCH_UART) { - /* TODO: What if it is part-way through clocking in junk? */ - udelay(100); - NS16550_clear(config->regs, config->port); - } } -void pinmux_select_uart(NS16550_t regs) +void pinmux_select_uart(void) { - /* Also prevents calling spi_uart_switch() before relocation */ - if (regs == local.regs) spi_uart_switch(&local, SWITCH_UART); } diff --git a/board/nvidia/dts/tegra2-harmony.dts b/board/nvidia/dts/tegra2-harmony.dts new file mode 100644 index 0000000000..4f60a05f33 --- /dev/null +++ b/board/nvidia/dts/tegra2-harmony.dts @@ -0,0 +1,57 @@ +/dts-v1/; + +/include/ ARCH_CPU_DTS + +/ { + model = "NVIDIA Tegra2 Harmony evaluation board"; + compatible = "nvidia,harmony", "nvidia,tegra20"; + + aliases { + usb0 = "/usb@c5008000"; + }; + + memory { + reg = <0x00000000 0x40000000>; + }; + + clocks { + clk_32k: clk_32k { + clock-frequency = <32000>; + }; + osc { + clock-frequency = <12000000>; + }; + }; + + clock@60006000 { + clocks = <&clk_32k &osc>; + }; + + serial@70006300 { + clock-frequency = < 216000000 >; + }; + + i2c@7000c000 { + status = "disabled"; + }; + + i2c@7000c400 { + status = "disabled"; + }; + + i2c@7000c500 { + status = "disabled"; + }; + + i2c@7000d000 { + status = "disabled"; + }; + + usb@c5000000 { + status = "disabled"; + }; + + usb@c5004000 { + status = "disabled"; + }; +}; diff --git a/board/nvidia/dts/tegra2-ventana.dts b/board/nvidia/dts/tegra2-ventana.dts new file mode 100644 index 0000000000..900e871d74 --- /dev/null +++ b/board/nvidia/dts/tegra2-ventana.dts @@ -0,0 +1,57 @@ +/dts-v1/; + +/include/ ARCH_CPU_DTS + +/ { + model = "NVIDIA Tegra2 Ventana evaluation board"; + compatible = "nvidia,ventana", "nvidia,tegra20"; + + aliases { + usb0 = "/usb@c5008000"; + }; + + memory { + reg = <0x00000000 0x40000000>; + }; + + clocks { + clk_32k: clk_32k { + clock-frequency = <32000>; + }; + osc { + clock-frequency = <12000000>; + }; + }; + + clock@60006000 { + clocks = <&clk_32k &osc>; + }; + + serial@70006300 { + clock-frequency = < 216000000 >; + }; + + i2c@7000c000 { + status = "disabled"; + }; + + i2c@7000c400 { + status = "disabled"; + }; + + i2c@7000c500 { + status = "disabled"; + }; + + i2c@7000d000 { + status = "disabled"; + }; + + usb@c5000000 { + status = "disabled"; + }; + + usb@c5004000 { + status = "disabled"; + }; +}; diff --git a/board/nvidia/dts/tegra2-whistler.dts b/board/nvidia/dts/tegra2-whistler.dts new file mode 100644 index 0000000000..b22d4073f6 --- /dev/null +++ b/board/nvidia/dts/tegra2-whistler.dts @@ -0,0 +1,67 @@ +/dts-v1/; + +/include/ ARCH_CPU_DTS + +/ { + model = "NVIDIA Tegra2 Whistler evaluation board"; + compatible = "nvidia,whistler", "nvidia,tegra20"; + + aliases { + i2c0 = "/i2c@7000d000"; + usb0 = "/usb@c5008000"; + usb1 = "/usb@c5000000"; + }; + + memory { + device_type = "memory"; + reg = < 0x00000000 0x20000000 >; + }; + + clocks { + osc { + clock-frequency = <12000000>; + }; + }; + + clock@60006000 { + clocks = <&clk_32k &osc>; + }; + + serial@70006000 { + clock-frequency = < 216000000 >; + }; + + i2c@7000c000 { + status = "disabled"; + }; + + i2c@7000c400 { + status = "disabled"; + }; + + i2c@7000c500 { + status = "disabled"; + }; + + i2c@7000d000 { + clock-frequency = <100000>; + + pmic@3c { + compatible = "maxim,max8907b"; + reg = <0x3c>; + + clk_32k: clock { + compatible = "fixed-clock"; + /* + * leave out for now due to CPP: + * #clock-cells = <0>; + */ + clock-frequency = <32768>; + }; + }; + }; + + usb@c5004000 { + status = "disabled"; + }; +}; diff --git a/board/nvidia/harmony/harmony.c b/board/nvidia/harmony/harmony.c index 8f8e7bf3fe..f27ad37b70 100644 --- a/board/nvidia/harmony/harmony.c +++ b/board/nvidia/harmony/harmony.c @@ -29,7 +29,7 @@ #include <asm/arch/pinmux.h> #include <asm/arch/mmc.h> #include <asm/gpio.h> -#ifdef CONFIG_TEGRA2_MMC +#ifdef CONFIG_TEGRA_MMC #include <mmc.h> #endif @@ -41,7 +41,7 @@ void gpio_config_uart(void) { } -#ifdef CONFIG_TEGRA2_MMC +#ifdef CONFIG_TEGRA_MMC /* * Routine: pin_mux_mmc * Description: setup the pin muxes/tristate values for the SDMMC(s) diff --git a/board/nvidia/seaboard/seaboard.c b/board/nvidia/seaboard/seaboard.c index 94efb1e83d..36039c4ed8 100644 --- a/board/nvidia/seaboard/seaboard.c +++ b/board/nvidia/seaboard/seaboard.c @@ -29,7 +29,7 @@ #include <asm/arch/pinmux.h> #include <asm/arch/mmc.h> #include <asm/gpio.h> -#ifdef CONFIG_TEGRA2_MMC +#ifdef CONFIG_TEGRA_MMC #include <mmc.h> #endif @@ -54,7 +54,7 @@ void gpio_config_uart(void) } #endif -#ifdef CONFIG_TEGRA2_MMC +#ifdef CONFIG_TEGRA_MMC /* * Routine: pin_mux_mmc * Description: setup the pin muxes/tristate values for the SDMMC(s) diff --git a/board/nvidia/whistler/Makefile b/board/nvidia/whistler/Makefile new file mode 100644 index 0000000000..a910577f21 --- /dev/null +++ b/board/nvidia/whistler/Makefile @@ -0,0 +1,48 @@ +# +# (C) Copyright 2010-2012 +# NVIDIA Corporation <www.nvidia.com> +# +# +# See file CREDITS for list of people who contributed to this +# project. +# +# This program is free software; you can redistribute it and/or +# modify it under the terms of the GNU General Public License as +# published by the Free Software Foundation; either version 2 of +# the License, or (at your option) any later version. +# +# This program is distributed in the hope that it will be useful, +# but WITHOUT ANY WARRANTY; without even the implied warranty of +# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +# GNU General Public License for more details. +# +# You should have received a copy of the GNU General Public License +# along with this program; if not, write to the Free Software +# Foundation, Inc., 59 Temple Place, Suite 330, Boston, +# MA 02111-1307 USA +# + +include $(TOPDIR)/config.mk + +ifneq ($(OBJTREE),$(SRCTREE)) +$(shell mkdir -p $(obj)../common) +endif + +LIB = $(obj)lib$(BOARD).o + +COBJS := $(BOARD).o + +SRCS := $(COBJS:.o=.c) +OBJS := $(addprefix $(obj),$(COBJS)) + +$(LIB): $(obj).depend $(OBJS) + $(call cmd_link_o_target, $(OBJS)) + +######################################################################### + +# defines $(obj).depend target +include $(SRCTREE)/rules.mk + +sinclude $(obj).depend + +######################################################################### diff --git a/board/nvidia/whistler/whistler.c b/board/nvidia/whistler/whistler.c new file mode 100644 index 0000000000..3ec24df2e7 --- /dev/null +++ b/board/nvidia/whistler/whistler.c @@ -0,0 +1,116 @@ +/* + * (C) Copyright 2010-2012 + * NVIDIA Corporation <www.nvidia.com> + * + * See file CREDITS for list of people who contributed to this + * project. + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of + * the License, or (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 59 Temple Place, Suite 330, Boston, + * MA 02111-1307 USA + */ + +#include <common.h> +#include <i2c.h> +#include <asm/io.h> +#include <asm/arch/tegra2.h> +#include <asm/arch/clock.h> +#include <asm/arch/funcmux.h> +#include <asm/arch/pinmux.h> +#include <asm/arch/mmc.h> +#include <asm/gpio.h> +#ifdef CONFIG_TEGRA_MMC +#include <mmc.h> +#endif + +/* + * Routine: gpio_config_uart + * Description: Does nothing on Whistler - no UART-related GPIOs. + */ +void gpio_config_uart(void) +{ +} + +/* + * Routine: pin_mux_mmc + * Description: setup the pin muxes/tristate values for the SDMMC(s) + */ +static void pin_mux_mmc(void) +{ + funcmux_select(PERIPH_ID_SDMMC3, FUNCMUX_SDMMC3_SDB_SLXA_8BIT); + funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATC_ATD_8BIT); +} + +/* this is a weak define that we are overriding */ +int board_mmc_init(bd_t *bd) +{ + uchar val; + int ret; + + debug("board_mmc_init called\n"); + + /* Turn on MAX8907B LDO12 to 2.8V for J40 power */ + ret = i2c_set_bus_num(0); + if (ret) + printf("i2c_set_bus_num failed: %d\n", ret); + val = 0x29; + ret = i2c_write(0x3c, 0x46, 1, &val, 1); + if (ret) + printf("i2c_write 0 0x3c 0x46 failed: %d\n", ret); + val = 0x00; + ret = i2c_write(0x3c, 0x45, 1, &val, 1); + if (ret) + printf("i2c_write 0 0x3c 0x45 failed: %d\n", ret); + val = 0x1f; + ret = i2c_write(0x3c, 0x44, 1, &val, 1); + if (ret) + printf("i2c_write 0 0x3c 0x44 failed: %d\n", ret); + + /* Enable muxes, etc. for SDMMC controllers */ + pin_mux_mmc(); + + /* init dev 0 (SDMMC4), (J29 "HSMMC") with 8-bit bus */ + tegra2_mmc_init(0, 8, -1, -1); + + /* init dev 1 (SDMMC3), (J40 "SDIO3") with 8-bit bus */ + tegra2_mmc_init(1, 8, -1, -1); + + return 0; +} + +/* this is a weak define that we are overriding */ +void pin_mux_usb(void) +{ + uchar val; + int ret; + + /* + * This is a hack. This should be represented in DT using the + * vbus-gpio property. However, U-Boot's DT support doesn't + * support any GPIO controller other than the Tegra's yet. + */ + + /* Turn on TAC6416's GPIO 0+1 for USB1/3's VBUS */ + ret = i2c_set_bus_num(0); + if (ret) + printf("i2c_set_bus_num failed: %d\n", ret); + val = 0x03; + ret = i2c_write(0x20, 2, 1, &val, 1); + if (ret) + printf("i2c_write 0 0x20 2 failed: %d\n", ret); + val = 0xfc; + ret = i2c_write(0x20, 6, 1, &val, 1); + if (ret) + printf("i2c_write 0 0x20 6 failed: %d\n", ret); +} |