| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
| |
Update patch with version submitted upstream.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The MT-3000 is a pocket-sized Wi-Fi 6 router based on MediaTek MT7981.
Specification:
- SoC: MediaTek MT7981B
- CPU: 2x 1.3 GHz Cortex-A53
- Flash: 256 MiB Macronix SPI NAND
- RAM: 512 MiB Nanya DDR4
- WLAN: 2.4 GHz, 5 GHz (MediaTek MT7976CN)
- Ethernet:
- 1x 10/100/1000 Mbps built-in PHY (LAN)
- 1x 10/100/1000/2500 Mbps MaxLinear GPY211 PHY (WAN)
- USB 3.0 port
- Buttons: 1 button, 1 switch
- LEDs: 1x light-blue, 1x warm-white
- Serial console: internal 4-pin header, 115200 8n1
- PWM controlled fan with tacho
- Power: 5 VDC, 3 A (USB Type-C)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
| |
|
|
|
|
|
| |
Import patch fixing the updated firmware path of mt7601u.bin.
Refresh patches while at it.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Hardware
--------
MediaTek MT7981 WiSoC
256MB DDR3 RAM
16MB SPI-NOR (XMC XM25QH128C)
MediaTek MT7981 2x2 DBDC 802.11ax 2T2R (2.4 / 5)
UART: 115200 8N1 3.3V
[LEDS] VCC-GND-RX-TX [ETH]
Header is located below the heatsink
Case
----
Unscrew the 4 bottom screws. Remove the top of the case by inserting a
small screwdriver into the ventilation holes and lift the top cover.
This works best by beginning near the ETH-ports. The top is clipped on
the front near the LEDs with two plastic clips. The back has a single
clip in the middle. Start at one of the back edges.
MAC-Addresses
-------------
80:AF:CA:00:F9:C6 LAN
80:AF:CA:00:F9:C7 WAN
80:AF:CA:00:F9:C6 W2
82:AF:CA:30:F9:C6 W5
Installation
------------
1. Connect to the serial port as described in the "Hardware" section.
2. Power on the device. Keep pressing the "0" key to enter the U-Boot
shell.
3. Download the OpenWrt initramfs image. Place it on an TFTP server
connected to the Cudy LAN ports. Make sure the server is reachable at
192.168.1.2. Rename the image to "cudy3000.bin"
4. Download and boot the OpenWrt initramfs image.
$ tftpboot 0x46000000 cudy3000.bin; bootm 0x46000000
5. Transfer the OpenWrt sysupgrade image to the device using scp.
Install with sysupgrade.
Note: Cudy does not yet provide a image for disabling their
signature-protection. This has happened in the past. Make sure to check
the wiki for a possible easier installation method.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
| |
|
|
|
|
|
| |
c9f5c3f devices: add MediaTek MT7981 WMAC compatible
b3888b2 devices: add compatible strings for Ralink WiSoCs
Signed-off-by: David Bauer <mail@david-bauer.net>
|
| |
|
|
|
|
| |
Package the firmware required for MT7981 to bring up the radio.
Signed-off-by: David Bauer <mail@david-bauer.net>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
969b7b5e wifi: mt76: mt7915: add support for MT7981
cddbd796 linux-firmware: add firmware for MT7981
c69b0239 linux-firmware: update firmware for MT7921 WiFi device
c85a0f2f mt7921: remove duplicated line
0cbe1376 wifi: mt76: mt7915: drop redundant prefix of mt7915_txpower_puts()
b490c6c7 wifi: mt76: fix 6GHz high channel not be scanned
db5a8f70 wifi: mt76: move shared mac definitions in mt76_connac2_mac.h
3963ab2f wifi: mt76: mt7921: get rid of eeprom.h
c09f943d wifi: mt76: add mt76_connac_gen_ppe_thresh utility routine
28ea992c wifi: mt76: get rid of unused sta_ps callbacks
2936b036 wifi: mt76: add mt76_connac_irq_enable utility routine
482d2a76 wifi: mt76: move irq_tasklet in mt76_dev struct
88d1b002 wifi: mt76: mt7996: enable mesh HW amsdu/de-amsdu support
577fbd47 linux-firmware: update firmware for MT7916
32be54b5 linux-firmware: update firmware for MT7921 WiFi device
4e2fad04 linux-firmware: update firmware for MT7922 WiFi device
f8793b1a linux-firmware: update firmware for MT7921 WiFi device
91e6ad2a linux-firmware: update firmware for MT7921 WiFi device
b7a538a3 linux-firmware: update firmware for MT7922 WiFi device
e3b5a8cc wifi: mt76: mt7996: enable configured beacon tx rate
a18bf481 wifi: mt76: mt7996: enable BSS_CHANGED_MCAST_RATE support
f863beed wifi: mt76: mt7996: enable BSS_CHANGED_BASIC_RATES support
aedc10d5 wifi: mt76: connac: add nss calculation into mt76_connac2_mac_tx_rate_val()
84a227e5 wifi: mt76: connac: fix txd multicast rate setting
a0657180 wifi: mt76: mt7921e: stop chip reset worker in unregister hook
fd895347 wifi: mt76: mt7921e: improve reliability of dma reset
c9fa8d64 wifi: mt76: mt7921: fix missing unwind goto in `mt7921u_probe`
c1baa812 mt76: mt7921: fix kernel panic by accessing unallocated eeprom.data
ca180889 wifi: mt76: move mcu_uni_event and mcu_reg_event in common code
98fbca7a wifi: mt76: mt7996: enable coredump support
be1ff24e wifi: mt76: mt7996: add full system reset knobs into debugfs
b7a6c0ef wifi: mt76: mt7996: enable full system reset support
46f28e75 wifi: mt76: mt7921: enable p2p support
6a7e41c3 wifi: mt76: mt7921e: Set memory space enable in PCI_COMMAND if unset
084e6de7 wifi: mt76: mt7921: use driver flags rather than mac80211 flags to mcu
c66e7a1a wifi: mt76: mt7921: introduce mt7921_get_mac80211_ops utility routine
821caac5 wifi: mt76: mt7996: fix eeprom tx path bitfields
9ae2569b wifi: mt76: mt7996: remove mt7996_mcu_set_pm()
3244d176 wifi: mt76: mt7996: init mpdu density cap
210a558a wifi: mt76: mt7996: fix pointer calculation in ie countdown event
207c92bb wifi: mt76: mt7996: remove unused eeprom band selection
16a24667 wifi: mt76: mt7996: let non-bufferable MMPDUs use correct hw queue
d39bb7c8 wifi: mt76: mt7996: remove mt7996_mcu_beacon_check_caps()
4046b591 wifi: mt76: mt7915: remove mt7915_mcu_beacon_check_caps()
d63cb85c wifi: mt76: add missing locking to protect against concurrent rx/status calls
22f1b777 mt76: adjust for ieee80211_is_bufferable_mmpdu API change
8ecf551c wifi: mt76: set NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 on supported drivers
efa44cb5 wifi: mt76: ignore key disable commands
56f0cd4d wifi: mt76: mt7915 add tc offloading support
021ded36 tools: Fix compile error with glibc
Signed-off-by: David Bauer <mail@david-bauer.net>
|
| |
|
|
| |
Signed-off-by: David Bauer <mail@david-bauer.net>
|
| |
|
|
|
|
|
| |
Add missing patch headers and regenerate the ones that contain an obsolete
patch header.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
_LARGEFILE64_SOURCE has to be defined in the source, or CFLAGS can be used
to pass -D_LARGEFILE64_SOURCE to allow to keep using LFS64 definitions.
Fixes error in the form of:
restripe.c: In function 'restore_stripes':
restripe.c:758:43: error: 'off64_t' undeclared (first use in this function); did you mean 'off_t'?
758 | (off64_t)read_offset) {
| ^~~~~~~
| off_t
restripe.c:758:43: note: each undeclared identifier is reported only once for each function it appears in
restripe.c:758:51: error: expected ')' before 'read_offset'
758 | (off64_t)read_offset) {
| ^~~~~~~~~~~
| )
restripe.c:757:36: note: to match this '('
757 | if (lseek64(source, read_offset, 0) !=
| ^
make[3]: *** [Makefile:193: restripe.o] Error 1
Fixes: fff878c5bcda ("toolchain/musl: update to 1.2.4")
Signed-off-by: Nick Hainke <vincent@systemli.org>
|
| |
|
|
|
|
|
|
|
| |
musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces and
autotools failed to check the lseek64 function.
Force enable ac_cv_func_lseek64 to workaround it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
|
| |
|
|
|
|
|
|
|
| |
musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces and
autotools failed to check the lseek64 function.
Force enable ac_cv_func_lseek64 to workaround it.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
MikroTik RB951Ui-2HnD is a wireless SOHO router that was previously
supported by the ar71xx target, see commit d19b868b12 ("ar71xx: Add
support for MikroTik RB951Ui-2HnD").
Specifications
--------------
- SoC: Atheros AR9344 (600 MHz)
- RAM: 128 MB (2x 64 MB)
- Storage: 128 MB NAND flash (various manufacturers)
- Ethernet: Atheros AR8229 switch, 5x 10/100 Mbit/s
- 1x PoE in (port 1, 8-30 V input)
- 1x PoE out (port 5, 500 mA output)
- Wireless: Atheros AR9340 (802.11b/g/n)
- USB: 2.0 (1A)
- 9x LED:
- 1x power (green, not configurable)
- 1x user (green)
- 5x FE ports (green)
- 1x wireless (green)
- 1x PoE out (red)
- 1x button (restart)
See https://mikrotik.com/product/RB951Ui-2HnD for more details.
Flashing
--------
TFTP boot initramfs image and then perform sysupgrade. Follow
common MikroTik procedures at https://openwrt.org/toh/mikrotik/common.
Signed-off-by: Michał Kępień <openwrt@kempniu.pl>
|
| |
|
|
|
|
|
|
|
|
|
| |
musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces so
just having _GNU_SOURCE defined is not enough anymore.
_LARGEFILE64_SOURCE has to be defined in the source, or CFLAGS can be used
to pass -D_LARGEFILE64_SOURCE to allow to keep using LFS64 definitions.
Fixes: fff878c5bcda ("toolchain/musl: update to 1.2.4")
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The firmware file for mt7601u (MediaTek MT7601U Wireless MACs) has
been moved to the mediatek/ folder by commit
8451c2b1 mt76xx: Move the old Mediatek WiFi firmware to mediatek
Address this by updating the location of the firmware file in our
linux-firmware Makefile generating the mt7601u-firmware package.
All other MediaTek Wi-Fi firmware files are supplied by OpenWrt's
own repository rather than being taken from linux-firmware.
Fixes: d53fe5d9ce ("linux-firmware: update to 20230515")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Package offloading firmware for MT7981 which has been added to
linux-firmware recently and became available in this release.
Changes since 20230515:
51290942 Merge branch 'main' of https://github.com/CirrusLogic/linux-firmware
cc628d65 cirrus: Add firmware and tuning files for HP G10 series laptops
905d3265 linux-firmware: update firmware for mediatek bluetooth chip (MT7922)
d1962891 WHENCE: Cleanup Realtek BT firmware provenance
6569484e linux-firmware: update firmware for MT7922 WiFi device
7d639e80 cnm: update chips&media wave521c firmware.
b8a56bf2 cirrus: Add firmware and tuning files for Lenovo ThinkPad P1 Gen 6
6c9e0ed5 check_whence: error on directory listed as File
05183b7b check_whence: error on duplicate file entries
c4423c91 WHENCE: comment out duplicate MediaTek firmware
2bc50f50 Merge branch 'mtl_guc_70.6.6' of git://anongit.freedesktop.org/drm/drm-firmware
192ee6d1 i915: Add GuC v70.6.6 for MTL
312c61f5 amdgpu: update DCN 3.1.6 DMCUB firmware
0061a2dd rtl_bt: Update RTL8852B BT USB firmware to 0xDBC6_B20F
1de22a39 rtl_bt: Update RTL8761B BT USB firmware to 0xDFC6_D922
dee0d4cd rtl_bt: Update RTL8761B BT UART firmware to 0x9DC6_D922
fab14965 Group all Conexant V4L devices together
e88bdbe4 rtl_nic: update firmware of USB devices
6536a964 linux-firmware: Update firmware file for Intel Bluetooth AX200
2ca17876 linux-firmware: Update firmware file for Intel Bluetooth AX201
7610656f linux-firmware: Update firmware file for Intel Bluetooth AX203
209ba083 linux-firmware: Update firmware file for Intel Bluetooth AX203
a2739f05 linux-firmware: Update firmware file for Intel Bluetooth AX211
1ee587d5 linux-firmware: Update firmware file for Intel Bluetooth AX211
40ba7eee linux-firmware: Update firmware file for Intel Bluetooth AX210
bcbbf6bf linux-firmware: update firmware for MT7981
507ee862 Merge branch 'main' of github.com:sampathnimmmala/bt_firmware
2c6be1a4 qca: Update firmware files for BT chip WCN6750
8451c2b1 mt76xx: Move the old Mediatek WiFi firmware to mediatek
53e48f93 rtl_bt: Add firmware and config files for RTL8851B
69143e8e linux-firmware: Update AMD cpu microcode
1c942e46 Merge branch 'for-upstream' of https://github.com/CirrusLogic/linux-firmware
45530bcb linux-firmware: add firmware for MT7981
0d02ce69 linux-firmware: update firmware for MT7921 WiFi device
2deb2d30 linux-firmware: update firmware for mediatek bluetooth chip (MT7921)
9fdb844b linux-firmware: update qat firmware
74afc00d linux-firmware: Add firmware for Cirrus CS35L41 on Lenovo Laptops
86da2ac9 Merge https://github.com/pkshih/linux-firmware
5d0d24b3 linux-firmware: update firmware for MT7916
0aea9cdf Merge branch 'ath10k-20230405' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/linux-firmware
9f7502f1 rtw89: 8852b: update format-1 fw to v0.29.29.1
b9c8e9f7 rtw89: 8852c: update fw to v0.27.56.13
d1dc3048 ath11k: WCN6855 hw2.0: update board-2.bin
8115bd84 ath11k: WCN6750 hw1.0: update to WLAN.MSL.1.0.1-01160-QCAMSLSWPLZ-1
7d2ab030 ath11k: QCN9074 hw1.0: update to WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
b58b0869 ath11k: IPQ8074 hw2.0: update to WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
0747362d ath11k: IPQ8074 hw2.0: update board-2.bin
7262bd5d ath11k: IPQ6018 hw1.0: update to WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
aa98ffa3 ath11k: IPQ6018 hw1.0: update board-2.bin
2c67adc9 ath10k: QCA99X0 hw2.0: update board-2.bin
a5dcb441 ath10k: QCA9984 hw1.0: update board-2.bin
d0731d40 ath10k: QCA9888 hw2.0: update board-2.bin
e13fedda ath10k: QCA6174 hw3.0: update board-2.bin
465dc284 ath10k: QCA4019 hw1.0: update board-2.bin
2e92a49f nvidia: update Tu10x and Tu11x signed firmware to support newer Turing HW
00258371 linux-firmware: update firmware for MT7922 WiFi device
33d8bf79 linux-firmware: update firmware for mediatek bluetooth chip (MT7922)
87bb6c9a Merge tag 'iwlwifi-fw-2023-03-30' of http://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware
956c1163 Merge branch 'mlimonci/update-dcn-3-1-4' of https://gitlab.freedesktop.org/superm1/linux-firmware
717e62eb linux-firmware: Amphion: Update vpu firmware
7bce2920 Merge https://github.com/pkshih/linux-firmware
78a8782a iwlwifi: add new FWs from core78-32 release
a91d0e78 iwlwifi: update 9000-family firmwares to core78-32
9ee24ce0 amdgpu: Update SDMA 6.0.1 firmware
7df2a1ae amdgpu: Add PSP 13.0.11 firmware
f098803d amdgpu: Update PSP 13.0.4 firmware
2cc9a4d0 amdgpu: Update GC 11.0.1 firmware
eb13e669 amdgpu: Update DCN 3.1.4 firmware
898b7def amdgpu: Add GC 11.0.4 firmware
e40a5b63 rtw88: 8822c: Update normal firmware to v9.9.15
bcdcfbcf linux-firmware: Update firmware file for Intel Bluetooth AX101
b422cdd6 linux-firmware: Update firmware file for Intel Bluetooth 9462
3e4c3b8d linux-firmware: Update firmware file for Intel Bluetooth 9462
6fcdb8e7 linux-firmware: Update firmware file for Intel Bluetooth 9560
46384d1c linux-firmware: Update firmware file for Intel Bluetooth 9560
1d797f86 linux-firmware: Update firmware file for Intel Bluetooth AX203
53c086b3 linux-firmware: Update firmware file for Intel Bluetooth AX203
9cc9745d linux-firmware: Update firmware file for Intel Bluetooth AX211
45319be8 linux-firmware: Update firmware file for Intel Bluetooth AX211
61d58194 linux-firmware: Update firmware file for Intel Bluetooth AX210
7f490a9a Merge branch 'dmc-adlp_2.19-mtl_2.12' of git://anongit.freedesktop.org/drm/drm-firmware
dcac1477 Merge branch 'mtk-20230315' of https://github.com/tinghan-shen/linux_fw_scp
1f82dd25 linux-firmware: add firmware files for NXP BT chipsets
49ad74b3 Merge https://github.com/pkshih/linux-firmware
2c07f017 rtw89: 8852b: update format-1 fw to v0.29.29.0
b50cf920 rtw89: 8852b: add format-1 fw v0.29.26.0
416a66ca rtw89: 8852b: rollback firmware to v0.27.32.1
a18a444b i915: Update MTL DMC to v2.12
4ee236db i915: Update ADLP DMC to v2.19
d0997ff6 mediatek: Update mt8192/mt8195 SCP firmware to support MM21 and MT21
c761dbe8 Merge tag 'iwlwifi-fw-2023-03-13' of http://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/linux-firmware
5bc279fb iwlwifi: update core69 and core72 firmwares for So device
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
| |
|
|
|
|
|
| |
Import patch to prevent crashes in case WO firmware is missing on devices
with only a single frontend (eg. MT7981+MT7976).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
| |
|
|
|
|
| |
Load appropriate firmware for wireless offloading on MT7981.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
| |
|
|
|
|
|
|
|
| |
Debian 10 LTS support ends on 6/2024, so it makes no sense to use it as
a base for 23.05 release, so lets switch to Debian 11 which should've
LTS support till 6/2026.
References: https://github.com/openwrt/buildbot/commit/f2744543fa8027117b254ba2f4fa4366149d5bfb
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
| |
|
|
|
|
|
|
|
|
| |
musl 1.2.4 deprecated legacy "LFS64" ("large file support") interfaces so
just having _GNU_SOURCE defined is not enough anymore.
_LARGEFILE64_SOURCE has to be defined in the source, or CFLAGS can be used
to pass -D_LARGEFILE64_SOURCE to allow to keep using LFS64 definitions.
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Release notes:
new features:
- large dns record lookups via tcp fallback
- new getaddrinfo EAI_NODATA result to distinguish NODATA/NxDomain
- support for new RELR compressed format for relative relocations
- sysconf keys for querying signal stack size requirements
- real vfork on riscv64
performance:
- mallocng no longer uses MADV_FREE (high performance cost, little gain)
- vdso clock_gettime is supported once again on 32-bit arm
compatibility:
- gethostbyname family now distinguishes NO_DATA from HOST_NOT_FOUND
- res_send now works with caller-provided edns0 queries
- arpa/nameser.h RR types list is now up-to-date
- previously-missing POSIX confstr keys have been added
- mntent interfaces now accept missing fields
- alt signal stack, if any, is now used for internal signals
- the LFS64 macros are no longer exposed without _LARGEFILE64_SOURCE
- memmem (POSIX-future) is now exposed in default feature profile
- pthread_atfork now admits calls from an application-provided malloc
- debugger tracking of shared libraries now works on MIPS PIE binaries
- sendmsg now supports up to SCM_MAX_FD fds in SCM_RIGHTS messages
bugs fixed:
- gethostbyname[2]_r wrongly returned nonzero (error) on negative result
- parallel v4/v6 address queries could fail on query id collisions
- spurious getaddrinfo/AI_ADDRCONFIG failures due to errno clobbering
- dns search domains ending in dot (including lone dot) broke lookups
- ipv6 servers in resolv.conf broke lookups on systems with v6 disabled
- systems with bindv6only failed to query both v4 and v6 nameservers
- res_mkquery mishandled consecutive final dots in name
- res_send could malfunction for very small answer buffer sizes
- resolver dns backend accepted answers with wrong (A vs AAAA) RR type
- getservbyport_r returned junk or ENOENT (vs ERANGE) on buffer size errors
- dns result parsing of malformed responses could process uninitialized data
- freopen didn't reset stream orientation (byte/wide) & encoding rule
- fwprintf didn't print most fields on open_wmemstream FILEs
- wide printf %lc ignored field width
- wide printf erroneously processed %n after encoding errors
- use of wide printf %9$ argument slot overflowed undersized buffer
- swprintf malfunctioned on nul character in output
- strverscmp ordered digit sequences vs nondigits incorrectly
- timer_create/SIGEV_THREAD failure leaked the thread
- semaphores were subject to missed-wake under certain usage patterns
- several possible rare deadlocks with lock handling at thread exit
- several possible rare deadlocks with aio and multithreaded fork
- dynamic linker relro processing was broken on archs w/variable pagesize
- async cancellation could run cancellation handlers in invalid context
- pthread_detach was wrongly a cancellation point in rare race code path
- use-after-close/double-close errors in mq_notify error paths
- mq_notify event thread wrongly ran with signals unmasked
- wcs{,n}cmp, wmemcmp returned wrong results when difference overflowed
- accept4, pipe2, and dup3 handled unknown flags wrong in fallback cases
- CPU_SETSIZE macro had wrong unit
- select fallback for pre-time64 kernels truncated timeout (vs clamping)
arch-specific bugs fixed:
- x32 new socketcalls took fallback path due to pointer sign extension
- x32 wait4 didn't fill rusage structure (time64 regression)
- x32 semtimedop mismatched timespec ABI with kernel (time64 regression)
- sigaction signal mask was bogus on or1k, microblaze, mips, and riscv
- powerpc-sf longjmp asm clobbered value argument
- or1k poll function passed timeout to syscall in wrong form
Removed upstreamed:
- 800-mips_pie_debug.patch
Manually rebased:
- 600-nftw-support-common-gnu-extension.patch
Signed-off-by: Linhui Liu <liulinhui36@gmail.com>
|
| |
|
|
|
|
|
| |
Configure gettext to require and link
to our local libunistring explicitly.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Running autoreconf or autogen.sh is causing
the gettext-runtime subdirectory to have a configure script
that looks for and attempts to link to an external libunistring.
However, the macros and symbols for supporting that configuration
are not present in this subdirectory yet.
This results in some host machines to not build the
included libunistring objects for libgrt,
but at the same time, also not input the proper flag to the linker
for linking to an external library when it is found or even when
explicitly setting configuration to use a prefix for libunistring,
resulting in the common linking failure "undefined reference".
Some similar (and old...) upstream commits do the same thing,
but only for gettext-tools and libgettextpo.
Ref: ae943bcc1 ("Link with libunistring, if it exists.") # gettext.git
Ref: 61e21a72f ("Avoid link error in programs that use libgettextpo.") # gettext.git
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
| |
|
|
|
|
|
|
| |
Add libunistring in order to link to gettext
and other packages directly
instead of the built-in substitute for it.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Following 5264296, Mirotik NAND devices now use yafut to flash the
kernel on devices. This method is incompatible with the old-style
"kernel2minor" flash mechanism.
Even though NAND images were disabled in default build since 21.02, a
user flashing a new-style image onto an old-style image would result in
in a soft-brick[1]. In order to prevent such accidental mishap,
especially as these device images will be reenabled in the upcoming
release, bump the compat version.
After the new image is flashed, the compat version can be updated:
uci set system.@system[0].compat_version='1.1'
uci commit
[1] https://github.com/openwrt/openwrt/pull/12225#issuecomment-1517529262
Cc: Michał Kępień <openwrt@kempniu.pl>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Reviewed-by: Robert Marko <robimarko@gmail.com>
|
| |
|
|
|
|
|
| |
Release Notes:
https://lore.kernel.org/netdev/20230508213111.z4vjg6gyrm7nwz4r@lion.mk-sys.cz/
Signed-off-by: Nick Hainke <vincent@systemli.org>
|
| |
|
|
|
|
|
| |
Release Notes:
https://github.com/strace/strace/releases/tag/v6.3
Signed-off-by: Nick Hainke <vincent@systemli.org>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Fix compilation warning for unused variable for vr9.
Fix compilation warning:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/ltq-ptm-vr9/ltq-ptm/ifxmips_ptm_vdsl.c: In function 'mailbox_irq_handler':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/ltq-ptm-vr9/ltq-ptm/ifxmips_ptm_vdsl.c:560:9: error: unused variable 'i' [-Werror=unused-variable]
560 | int i;
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
| |
|
|
|
|
|
|
| |
Refresh patches to make them cleanly apply.
This problem was found by the github CI.
Fixes: ecd9abc8c082 ("kernel: use upstream firmware patch for Broadcom's NVRAM")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
| |
|
|
|
|
|
| |
It has just been queued for the v6.5. It allows Ethernet drivers to read
MACs from NVRAM using NVMEM interface.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
| |
|
|
|
|
| |
This replaces our 2 downstream patches.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fix multiple compilation warning for fallthrough and unused functions.
Fix compilation warning:
home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_device_vrx.c: In function 'DSL_DRV_VRX_TestParametersFeUpdate':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_device_vrx.c:3359:17: error: unused variable 'nMsgId' [-Werror=unused-variable]
3359 | DSL_uint16_t nMsgId = EVT_PMD_TESTPARAMSGET;
| ^~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_device_vrx.c: In function 'DSL_DRV_DEV_AutobootHandleTraining':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_device_vrx.c:8310:19: error: this statement may fall through [-Werror=implicit-fallthrough=]
8310 | bPreFail = DSL_TRUE;
| ~~~~~~~~~^~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_device_vrx.c:8316:7: note: here
8316 | case DSL_LINESTATE_EXCEPTION:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/pm/drv_dsl_cpe_pm_core.c: In function 'DSL_DRV_PM_CountersReset':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/pm/drv_dsl_cpe_pm_core.c:2328:7: error: this statement may fall through [-Werror=implicit-fallthrough=]
2328 | if (ResetType == DSL_PM_RESET_HISTORY)
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/pm/drv_dsl_cpe_pm_core.c:2331:4: note: here
2331 | case DSL_PM_RESET_TOTAL:
| ^~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/common/drv_dsl_cpe_os_linux.c: In function 'DSL_ModuleCleanup':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/common/drv_dsl_cpe_os_linux.c:1266:13: error: assignment to 'dev_t' {aka 'unsigned int'} from 'void *' makes integer from pointer without a cast [-Werror=int-conversion]
1266 | dsl_devt = NULL;
| ^
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/common/drv_dsl_cpe_os_linux.c: At top level:
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/common/drv_dsl_cpe_os_linux.c:1178:13: error: 'DSL_DRV_NlSendMsg' defined but not used [-Werror=unused-function]
1178 | static void DSL_DRV_NlSendMsg(DSL_char_t* pMsg)
| ^~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_dsl_cpe_api-4.17.18.6/src/device/drv_dsl_cpe_msg_vrx.c:2459:20: error: 'DSL_DRV_VRX_SpreadArray' defined but not used [-Werror=unused-function]
2459 | static DSL_Error_t DSL_DRV_VRX_SpreadArray(
| ^~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fix simple compilation warning due to cast and wrong include.
Fix compilation warning:
In file included from ./include/linux/compat.h:18,
from ./include/linux/filter.h:10,
from ./include/net/sock.h:59,
from /home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_mei_cpe-1.5.17.6/src/drv_mei_cpe_linux.c:70:
./include/uapi/linux/aio_abi.h:77:45: error: "__LITTLE_ENDIAN" is not defined, evaluates to 0 [-Werror=undef]
77 | #if defined(__BYTE_ORDER) ? __BYTE_ORDER == __LITTLE_ENDIAN : defined(__LITTLE_ENDIAN)
| ^~~~~~~~~~~~~~~
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_mei_cpe-1.5.17.6/src/drv_mei_cpe_linux.c: In function 'MEI_MeminfoProcPerDevGet':
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_mei_cpe-1.5.17.6/src/drv_mei_cpe_linux.c:1715:56: error: format '%X' expects argument of type 'unsigned int', but argument 4 has type 'IFX_uint8_t *' {aka 'unsigned char *'} [-Werror=format=]
1715 | seq_printf(s, "chunk[%02d]: addr = 0x%08X (0x%08X), "
| ~~~^
| |
| unsigned int
| %08hhn
......
1721 | chunkIdx, pChunk[chunkIdx].pImageChunk_aligned,
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| |
| IFX_uint8_t * {aka unsigned char *}
/home/ansuel/openwrt-ansuel/openwrt/build_dir/target-mips-openwrt-linux-musl_musl/linux-lantiq_xrx200/drv_mei_cpe-1.5.17.6/src/drv_mei_cpe_linux.c:1715:64: error: format '%X' expects argument of type 'unsigned int', but argument 5 has type 'IFX_uint8_t *' {aka 'unsigned char *'} [-Werror=format=]
1715 | seq_printf(s, "chunk[%02d]: addr = 0x%08X (0x%08X), "
| ~~~^
| |
| unsigned int
| %08hhn
......
1722 | pChunk[chunkIdx].pImageChunk_allocated,
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| |
| IFX_uint8_t * {aka unsigned char *}
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
Add patch fixing compilation warning related to stack limit.
Fix compilation warning:
/builder/shared-workdir/build/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/ltq-vectoring-2019-05-20-4fa7ac30/src/vectoring/ifxmips_vectoring.c: In function 'proc_write_dbg':
/builder/shared-workdir/build/build_dir/target-mips_24kc_musl/linux-lantiq_xrx200/ltq-vectoring-2019-05-20-4fa7ac30/src/vectoring/ifxmips_vectoring.c:369:1: error: the frame size of 2088 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
369 | }
| ^
cc1: all warnings being treated as errors
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The following adds the Aerohive BR200-WP router to OpenWrt under
the mpc85xx/p1010 subtarget.
Hardware:
- SoC: Freescale P1011
- NOR: Intel JS28F512M29EWH 64MB
- Memory: 2x Nanya NT5TU64M16GG-AC 128MB (Total of 256MB)
- 2.4GHz WiFi: Atheros AR9390-AL1A
- Eth1: Atheros AR8035-A PoE
- 2x LEDs
- 1x Button
- PoE PSE
Flashing:
1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a
password of administrator or AhNf?d@ta06 if prompted.
2. Once in U-Boot, tftp boot the initramfs image:
dhcp; setenv serverip 192.168.1.3;
tftpboot 0x2004000 openwrt-mpc85xx-p1010-aerohive_br200-wp-initramfs-kernel.bin;
bootm 0x2004000;
3. Once booted, scp over the sysupgrade file and sysupgrade the device
to flash LEDE to the NOR.
Note:
MAC assigns are taken from stock firmware:
Name MAC addr Mode State Chan(Width) VLAN Radio Hive SSID
-------- -------------- -------- ----- ----------- ---- ---------- ---------- ---------
Mgt0 08ea:44XX:XXc0 - U - 1 - hive0 -
Eth0 08ea:44XX:XXc0 wan U - - - - -
Eth1 08ea:44XX:XXc2 access D - - - hive0 -
Eth2 08ea:44XX:XXc3 access D - - - hive0 -
Eth3 08ea:44XX:XXc4 access D - - - hive0 -
Eth4 08ea:44XX:XXc5 access D - - - hive0 -
Wifi0 08ea:44XX:XXd0 access U 1(20MHz) - radio_ng0 - -
Wifi0.1 08ea:44XX:XXd4 access D 1(20MHz) - radio_ng0 hive0 -
Note2:
PoE PSE could be managed with `realtek-poe` package. Example port
config:
config port
option enable '1'
option id '4'
option name 'lan2'
option poe_plus '0'
option priority '2'
config port
option enable '1'
option id '3'
option name 'lan1'
option poe_plus '0'
option priority '1'
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(switch@0 -> switch@10, Device's quickstart says LEDs are
amber and white => add function+color properties but keep
labels around, use pr_info)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
DTSes from of three boards was sent and accpeted upstream. Let's use
backport patches with small OpenWrt tweak like other upstream stuff.
List of boards:
- Zyxel NSA310S
- Endian 4i Edge 200
- Ctera C-200 V1
Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Specifications:
SOC: Atheros/Qualcomm QCA9557-AT4A @ 720MHz
RAM: 2x Winbond W9751G6KB-25 (128 MiB)
FLASH: Hynix H27U1G8F2BTR-BC TSOP48 ONFI NAND (128 MiB)
WIFI1: Atheros AR9550 5.0GHz (SoC)
WIFI2: Atheros AR9582-AR1A 2.4GHz
WIFI2: Atheros AR9582-AR1A 2.4GHz + 5GHz
PHYETH: Atheros AR8035-A, 802.3af PoE capable Atheros (1x Gigabit LAN)
LED: 1x Power-LED, 1 x RGB Tricolor-LED
INPUT: One Reset Button
UART: JP1 on PCB (Labeled UART), 3.3v-Level, 115200n8
(VCC, RX, TX, GND - VCC is closest to the boot set jumper
under the console pins.)
Flashing instructions:
Depending on the installed firmware, there are vastly different
methods to flash a MR18. These have been documented on:
<https://openwrt.org/toh/meraki/mr18>
Tip:
Use an initramfs from a previous release and then use sysupgrade
to get to the later releases. This is because the initramfs can
no longer be built by the build-bots due to its size (>8 MiB).
Note on that:
Upgrades from AR71XX releases are possible, but they will
require the force sysupgrade option ( -F ).
Please backup your MR18's configuration before starting the
update. The reason here is that a lot of development happend
since AR71XX got removed, so I do advise to use the ( -n )
option for sysupgrade as well. This will cause the device
to drop the old AR71xx configuration and make a new
configurations from scratch.
Note on LEDs:
The LEDs has changed since AR71XX. The white LED is now used during
the boot and when upgrading instead of the green tricolor LED. The
technical reason is that currently the RGB-LED is brought up later
by a userspace daemon.
(added warning note about odm-caldata partition. remove initramfs -
it's too big to be built by the bots. MerakiNAND -> meraki-header.
sort nu801's targets)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
| |
|
|
|
|
|
|
|
|
| |
This sort of reverts Koen Vandeputte's commit
6561ca1fa51 ("ath79: ar934x: fix mounting issues if subpage is not supported")
since it does not work on the MR18 as the UBI is coming from
Meraki in that way and it used to work with AR71XX before.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
| |
|
|
|
|
|
| |
This is necessary to support the Meraki MR18 and likely Z1
as well.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
| |
Two Mikrotik board families (SXT 5nD R2 and Routerboard 92x are using
software ECC on NAND. Some of them use chips capable of subpage write,
others do not - within the same family, and a common block size is
required for UBI, to avoid mounting errors. Set the ECC step size
explicitly for them to 2048B, so UBI can mount existing volumes without
problems, at the same time allowing to unlocking subpage write functionality,
reuqired for Meraki MR18.
Fixes: 6561ca1fa51 ("ath79: ar934x: fix mounting issues if subpage is not supported")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
|
| |
|
|
|
|
|
| |
specify that this functions adds a Cisco Meraki
special-sauce header for their custom loader/uboot.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Removed upstreamed:
01. backport-5.15/424-v6.4-0001-mtd-core-provide-unique-name-for-nvmem-device-take-t.patch
02. backport-5.15/424-v6.4-0002-mtd-core-fix-nvmem-error-reporting.patch
03. generic-backport/424-v6.4-0003-mtd-core-fix-error-path-for-nvmem-provider.patch
04. generic-backport/828-v6.4-0001-of-Fix-modalias-string-generation.patch
05. bcm4908/patches-5.15/031-v5.17-0002-arm64-dts-broadcom-bcm4908-add-DT-for-Netgear-RAXE50.patch
06. bcm4908/patches-5.15/033-v6.0-0001-arm64-dts-Add-DTS-files-for-bcmbca-SoC-BCM63158.patchgit
07. bcm4908/patches-5.15/033-v6.0-0002-arm64-dts-Add-DTS-files-for-bcmbca-SoC-BCM4912.patchgita
08. bcm4908/patches-5.15/033-v6.0-0010-arm64-dts-Add-base-DTS-file-for-bcmbca-device-Asus-G.patchgit
09. bcm4908/patches-5.15/034-v6.1-0005-arm64-dts-Move-BCM4908-dts-to-bcmbca-folder.patch
10. bcm4908/patches-5.15/036-v6.4-0002-arm64-dts-broadcom-bcmbca-bcm4908-fix-NAND-interrupt.patch
11. bcm4908/patches-5.15/036-v6.4-0004-arm64-dts-broadcom-bcmbca-bcm4908-fix-procmon-nodena.patch
12. ipq806x/patches-5.15/104-v6.0-06-ARM-dts-qcom-ipq8064-reduce-pci-IO-size-to-64K.patch
Manually rebased:
bcm27xx/patches-5.15/950-0078-BCM2708-Add-core-Device-Tree-support.patch
bcm27xx/patches-5.15/950-0547-ARM-dts-Add-Pi-Zero-2-support.patch
bcm4908/patches-5.15/033-v6.0-0001-arm64-dts-Add-DTS-files-for-bcmbca-SoC-BCM63158.patchgit
bcm4908/patches-5.15/033-v6.0-0002-arm64-dts-Add-DTS-files-for-bcmbca-SoC-BCM4912.patchgit
bcm4908/patches-5.15/030-v5.16-0001-arm64-dts-broadcom-bcm4908-Fix-NAND-node-name.patch
bcm4908/patches-5.15/032-v5.18-0002-arm64-dts-broadcom-bcm4908-add-pinctrl-binding.patch
bcm4908/patches-5.15/032-v5.18-0003-arm64-dts-broadcom-bcm4908-add-watchdog-block.patch
bcm4908/patches-5.15/032-v5.18-0004-arm64-dts-broadcom-bcm4908-add-I2C-block.patch
bcm4908/patches-5.15/033-v6.0-0003-ARM64-dts-Add-DTS-files-for-bcmbca-SoC-BCM6858.patchgit
bcm4908/patches-5.15/033-v6.0-0008-arm64-dts-broadcom-bcm4908-Fix-timer-node-for-BCM490.patchgit
bcm4908/patches-5.15/034-v6.1-0001-arm64-dts-broadcom-bcm4908-add-remaining-LED-pins.patch
bcm4908/patches-5.15/034-v6.1-0002-arm64-dts-broadcom-bcm4908-add-LEDs-controller-block.patch
bcm4908/patches-5.15/034-v6.1-0003-arm64-dts-broadcom-bcm4908-add-Asus-GT-AC5300-LEDs.patch
bcm4908/patches-5.15/034-v6.1-0004-arm64-dts-bcmbca-update-BCM4908-board-dts-files.patch
All other patches automatically rebased.
Build system: x86_64
Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod
01. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=77112d23a671697f0f70695ab901f807e15d2093
02. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=fe07b3b5af01f42b291f5da0da09d047f50b33a6
03. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=273be36e420924237f6c9d43cdad96718c13dd52
04. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=fe8ab85ed4958e58e991bba0aa0a655b552b0273
05. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=6ae67829fa5e9e71f458f69db42f0e216225616a
06. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=1994284cb9226b65ca3a6744ce3320218b584f26
07. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=a46878476c5549a4fde15a31922ce80a50b23492
08. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=112ff0f2530549d50510f116474924f9c4fad590
09. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=7c253e98685e6d884d12e2618ef4d2ad90b4fbd7
10. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=8444b46e163aa9559a0af0381a1d230ec4146eb2
11. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=6d1af517817a760d7af3dee0fc4603645485495c
12. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.111&id=cc4f0e168a5630ad0491ac5328f1a89f3cf3d04e
Signed-off-by: John Audia <therealgraysky@proton.me>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
some targets do not define the _REDIR_TIME64 macro resulting in a
build error regression since ddfe5678a448ac8875e94f2fb4ddca67416fa14a
fix by checking if the macro is defined
[1] https://github.com/openwrt/openwrt/issues/12587
Fixes: #12587
Fixes: ddfe5678a448 ("fortify-headers: fix inconsistent time_t version of ppoll")
Signed-off-by: Georgi Valkov <gvalkov@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
d4f56f0e6971 add support for handling traffic to/from the bridge device
3ea579064c00 nl: add separate socket for netlink commands
4ec5a51c6d01 nl: fetch packet stats for offloaded flows
0319fd080bf5 add support for configuring a fixed output port for a bridge member port
5b730f0c2cf5 bridger-bpf: fix build on older kernels
00af6c6e8350 nl: process IFLA_MASTER in any nl events, but skip wireless events
a2794f95756e bridger-bpf: add bpf_skb_pull_data call
6974093eb036 nl: rework vlan code to use the iflink API
d0f79a16c749 nl: do not attempt to enable flow offload on older kernels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Allowing the (kernel) packet priority to be set through UCI.
This makes it straightforward to set some VLAN priority for DHCP
requests through a simple egress qos map. (Avoiding the need for
firewall matching and marking through iptables, which prevents using
flow offloading).
(Such priority tag is a hard requirement for some ISPs, such as Orange
in France).
Depends on: https://github.com/openwrt/odhcp6c/pull/74
Signed-off-by: Pacien TRAN-GIRARD <pacien.trangirard@pacien.net>
|
| |
|
|
|
|
| |
bcd2836 odhcp6c: add -K option to set packet kernel priority
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
|
| |
|
|
|
|
| |
All package feeds have been refactored to PKG_BUILD_FLAGS:=no-mips16.
Signed-off-by: Andre Heider <a.heider@gmail.com>
|
| |
|
|
|
|
|
| |
We switched to 5.15 kernel, so we don't need to maintain 5.10
compatibility anymore.
Signed-off-by: Nick Hainke <vincent@systemli.org>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
We only use 5.15 kernel. So remove all those unnecessary symbols
referencing 5.10 or 5.15 kernel.
Can be found with:
git grep -E 'LINUX_5_1(0|5)'
Note that we remove the dependency from "sound-soc-chipdip-dac" instead
of removing the complete kernel package. The 5.15 version bump forgot to
delete the "@LINUX_5_10" dependency. The kernel package is still needed
in 5.15 kernel.
Signed-off-by: Nick Hainke <vincent@systemli.org>
|
| |
|
|
|
|
| |
We only use 5.15 kernel. So remove all those unnecessary appearances.
Signed-off-by: Nick Hainke <vincent@systemli.org>
|
